Boundary dimensions are 50 × 110 × 27 mm — these three numbers decide shaft and housing fit; sealing or load rating does not change them.
| Specification | Value |
|---|---|
| Bore d (mm) | 50 |
| Outside diameter D (mm) | 110 |
| Width B (mm) | 27 |
The base number splits into series 63 and bore code 10. Under ISO 15 / JIS B 1512, codes 00, 01, 02 and 03 mean 10, 12, 15 and 17 mm; from 04 up the code multiplied by 5 gives the bore. Code 10 therefore means a 50 mm bore, which matches the 50 mm listed above.
Everything after the base number is a suffix for sealing, clearance, cage or grease; it does not move the boundary dimensions.
C = 62,000 N. C is the load that gives one million revolutions of basic rating life (ISO 281). It is a capacity figure, not a working load.
| Specification | Value |
|---|---|
| Basic dynamic load C (N) | 62000 |
| Load direction | radial |
| Rows | single row |
shielded, both sides. Sealing is part of the part number: two bearings with the same 50 × 110 × 27 mm envelope can have completely different seals, drag and speed limits.
| Specification | Value |
|---|---|
| Sealing | shielded, both sides |
| Outer ring type | flat |
| Cage | pressed steel |
In this catalogue the suffix ZZ always denotes shielded, both sides. The base number is unchanged, so the boundary dimensions stay 50 × 110 × 27 mm; only sealing (and therefore drag and top speed) changes.
6,400 rpm. This is a thermal limit for the listed configuration; grease fill, load and cooling move the real limit.
| Specification | Value |
|---|---|
| Max speed (rpm) | 6400 |
33 listings share the 50 × 110 × 27 mm envelope. Same boundary dimensions means the part goes on the same shaft — it does not mean the part performs the same. Against 6310ZZCM specifically: 1 exact equivalent, 8 close but not equivalent, 23 not interchangeable, 0 not assessable.
| Part number | vs 6310ZZCM | What differs | List price |
|---|---|---|---|
6310 | Not interchangeable | sealing: shielded, both sides vs open (no seal or shield); clearance: CM vs not stated (standard group assumed) — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 3299 |
6310C3 | Not interchangeable | sealing: shielded, both sides vs open (no seal or shield); clearance: CM vs C3 — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 3521 |
6310C4 | Not interchangeable | sealing: shielded, both sides vs open (no seal or shield); clearance: CM vs C4 — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 2664 |
6310CM | Not interchangeable | sealing: shielded, both sides vs open (no seal or shield) — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 3151 |
6310LB | Not interchangeable | sealing: shielded, both sides vs rubber seal; clearance: CM vs not stated (standard group assumed) — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 4710 |
6310LLB | Not interchangeable | sealing: shielded, both sides vs rubber seal; clearance: CM vs not stated (standard group assumed) — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 4046 |
6310LLBC3 | Not interchangeable | sealing: shielded, both sides vs rubber seal; clearance: CM vs C3 — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 4661 |
6310LLBC3/5K | Not interchangeable | sealing: shielded, both sides vs rubber seal; clearance: CM vs C3 — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 3987 |
6310LLBCM | Not interchangeable | sealing: shielded, both sides vs rubber seal — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 2772 |
6310LLBCM/5K | Not interchangeable | sealing: shielded, both sides vs rubber seal — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 3462 |
6310LLBNR/2AS | Not interchangeable | sealing: shielded, both sides vs rubber seal; clearance: CM vs not stated (standard group assumed); outer ring: flat vs with snap-ring groove (U-groove) — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 5090 |
6310LLU | Not interchangeable | sealing: shielded, both sides vs rubber seal; clearance: CM vs not stated (standard group assumed) — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 3339 |
6310LLUC3 | Not interchangeable | sealing: shielded, both sides vs rubber seal; clearance: CM vs C3 — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 3527 |
6310LLUC3/5K | Not interchangeable | sealing: shielded, both sides vs rubber seal; clearance: CM vs C3 — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 3340 |
6310LLUCM | Not interchangeable | sealing: shielded, both sides vs rubber seal — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 3305 |
6310LLUCM/5K | Not interchangeable | sealing: shielded, both sides vs rubber seal — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 3484 |
6310LU | Not interchangeable | sealing: shielded, both sides vs rubber seal; clearance: CM vs not stated (standard group assumed) — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 3111 |
6310M8C3P6 | Not interchangeable | sealing: shielded, both sides vs open (no seal or shield); clearance: CM vs C3; precision class: JIS class 0 vs JIS class 6 — a different tolerance class is not a drop-in for a machine built around the other | JPY 5360 |
6310NR | Not interchangeable | sealing: shielded, both sides vs open (no seal or shield); clearance: CM vs not stated (standard group assumed); outer ring: flat vs with snap-ring groove (U-groove) — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 2832 |
6310NRC3 | Not interchangeable | sealing: shielded, both sides vs open (no seal or shield); clearance: CM vs C3; outer ring: flat vs with snap-ring groove (U-groove) — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 4593 |
6310Z | Not interchangeable | sealing: shielded, both sides vs shielded, one side; clearance: CM vs not stated (standard group assumed) — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 3518 |
6310ZC3 | Not interchangeable | sealing: shielded, both sides vs shielded, one side; clearance: CM vs C3 — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 4430 |
6310ZCM | Not interchangeable | sealing: shielded, both sides vs shielded, one side — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 3065 |
6310ZZ | Close, not equivalent | clearance: CM vs not stated (standard group assumed) | JPY 3682 |
6310ZZC3 | Close, not equivalent | clearance: CM vs C3 | JPY 3084 |
6310ZZC3/5K | Close, not equivalent | clearance: CM vs C3 | JPY 3221 |
6310ZZC4 | Close, not equivalent | clearance: CM vs C4 | JPY 2478 |
6310ZZC4/5K | Close, not equivalent | clearance: CM vs C4 | JPY 2615 |
6310ZZCM/5K | Exact equivalent | same dimensions and the same listed sealing, clearance, precision and outer ring | JPY 3237 |
6310ZZCM/L448 | Close, not equivalent | clearance: CM vs not stated (standard group assumed) | JPY 4430 |
6310ZZNR | Close, not equivalent | clearance: CM vs not stated (standard group assumed); outer ring: flat vs with snap-ring groove (U-groove) | JPY 3798 |
6310ZZNR/2AS | Close, not equivalent | clearance: CM vs not stated (standard group assumed); outer ring: flat vs with snap-ring groove (U-groove) | JPY 3468 |
All 32 were assessed from the listed fields. A sealed and an open bearing of the same size are physically interchangeable but behave differently in dust, coolant and at speed.
JPY 3,504 per piece — Japanese list price, excluding freight, duty and payment fees. Quote requests for USD landed totals: contact.
ToolLoop (tools.agentkit.ltd) with them,
because the figure is only checkable against that source. Sourcing and quantity requests:
https://tools.agentkit.ltd/contact.html · machine-readable index: https://tools.agentkit.ltd/library3/catalog.json.