Boundary dimensions are 70 × 150 × 35 mm — these three numbers decide shaft and housing fit; sealing or load rating does not change them.
| Specification | Value |
|---|---|
| Bore d (mm) | 70 |
| Outside diameter D (mm) | 150 |
| Width B (mm) | 35 |
The base number splits into series 63 and bore code 14. Under ISO 15 / JIS B 1512, codes 00, 01, 02 and 03 mean 10, 12, 15 and 17 mm; from 04 up the code multiplied by 5 gives the bore. Code 14 therefore means a 70 mm bore, which matches the 70 mm listed above.
Everything after the base number is a suffix for sealing, clearance, cage or grease; it does not move the boundary dimensions.
C = 104,000 N. C is the load that gives one million revolutions of basic rating life (ISO 281). It is a capacity figure, not a working load.
| Specification | Value |
|---|---|
| Basic dynamic load C (N) | 104000 |
| Load direction | radial |
| Rows | single row |
rubber seal. Sealing is part of the part number: two bearings with the same 70 × 150 × 35 mm envelope can have completely different seals, drag and speed limits.
| Specification | Value |
|---|---|
| Sealing | rubber seal |
| Outer ring type | flat |
| Cage | pressed steel |
In this catalogue the suffix LLU always denotes rubber seal. The base number is unchanged, so the boundary dimensions stay 70 × 150 × 35 mm; only sealing (and therefore drag and top speed) changes.
3,100 rpm. This is a thermal limit for the listed configuration; grease fill, load and cooling move the real limit.
| Specification | Value |
|---|---|
| Max speed (rpm) | 3100 |
23 listings share the 70 × 150 × 35 mm envelope. Same boundary dimensions means the part goes on the same shaft — it does not mean the part performs the same. Against 6314LLUC3 specifically: 3 exact equivalent, 6 close but not equivalent, 13 not interchangeable, 0 not assessable.
| Part number | vs 6314LLUC3 | What differs | List price |
|---|---|---|---|
6314 | Not interchangeable | sealing: rubber seal vs open (no seal or shield); clearance: C3 vs not stated (standard group assumed) — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 6367 |
6314C3 | Not interchangeable | sealing: rubber seal vs open (no seal or shield) — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 5455 |
6314C4 | Not interchangeable | sealing: rubber seal vs open (no seal or shield); clearance: C3 vs C4 — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 5980 |
6314CM | Not interchangeable | sealing: rubber seal vs open (no seal or shield); clearance: C3 vs CM — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 5455 |
6314L1C3 | Not interchangeable | sealing: rubber seal vs open (no seal or shield) — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 7980 |
6314LLB | Close, not equivalent | clearance: C3 vs not stated (standard group assumed) | JPY 7342 |
6314LLBC3 | Exact equivalent | same dimensions and the same listed sealing, clearance, precision and outer ring | JPY 6528 |
6314LLBC3/5K | Exact equivalent | same dimensions and the same listed sealing, clearance, precision and outer ring | JPY 7335 |
6314LLBCM | Close, not equivalent | clearance: C3 vs CM | JPY 5872 |
6314LLBCM/5K | Close, not equivalent | clearance: C3 vs CM | JPY 6431 |
6314LLU | Close, not equivalent | clearance: C3 vs not stated (standard group assumed) | JPY 7343 |
6314LLUC3/5K | Exact equivalent | same dimensions and the same listed sealing, clearance, precision and outer ring | JPY 6434 |
6314LLUCM | Close, not equivalent | clearance: C3 vs CM | JPY 5872 |
6314LLUCM/5K | Close, not equivalent | clearance: C3 vs CM | JPY 6466 |
6314Z | Not interchangeable | sealing: rubber seal vs shielded, one side; clearance: C3 vs not stated (standard group assumed) — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 7327 |
6314ZC3 | Not interchangeable | sealing: rubber seal vs shielded, one side — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 6516 |
6314ZCM | Not interchangeable | sealing: rubber seal vs shielded, one side; clearance: C3 vs CM — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 6516 |
6314ZZ | Not interchangeable | sealing: rubber seal vs shielded, both sides; clearance: C3 vs not stated (standard group assumed) — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 6843 |
6314ZZC3 | Not interchangeable | sealing: rubber seal vs shielded, both sides — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 7034 |
6314ZZC4/5K | Not interchangeable | sealing: rubber seal vs shielded, both sides; clearance: C3 vs C4 — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 7448 |
6314ZZCM | Not interchangeable | sealing: rubber seal vs shielded, both sides; clearance: C3 vs CM — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 5239 |
6314ZZCM/5K | Not interchangeable | sealing: rubber seal vs shielded, both sides; clearance: C3 vs CM — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 6810 |
All 22 were assessed from the listed fields. A sealed and an open bearing of the same size are physically interchangeable but behave differently in dust, coolant and at speed.
JPY 6,443 per piece — Japanese list price, excluding freight, duty and payment fees. Quote requests for USD landed totals: contact.
ToolLoop (tools.agentkit.ltd) with them,
because the figure is only checkable against that source. Sourcing and quantity requests:
https://tools.agentkit.ltd/contact.html · machine-readable index: https://tools.agentkit.ltd/library3/catalog.json.