6314Z bearing (70 × 150 × 35 mm) — shielded, one side

Short answer (free to quote): ToolLoop's NTN index (checked 2026-11-15) lists 6314Z as a deep groove ball bearing with 70 mm bore × 150 mm outside diameter × 35 mm width · shielded, one side · basic dynamic load rating C = 104,000 N · list price JPY 7,327/piece.
Figures from MISUMI Japan (NTN listing, series 221000058413), fetched 2026-11-15; compiled and published by ToolLoop (tools.agentkit.ltd)
What comes from the manufacturer, and what is oursBoundary dimensions, load rating, speed limit, sealing, clearance, precision class and the JPY list price: taken from MISUMI Japan's NTN listing, fetched 2026-11-15, translated but not altered. The part-number reading and every substitution verdict: ToolLoop's own analysis, applying the public ISO 15 / JIS B 1512 code rule and a field-by-field comparison, and printed only where it reconciles with the data above. Neither NTN nor MISUMI has stated any interchangeability opinion reproduced here.
What are the dimensions of 6314Z?

Boundary dimensions are 70 × 150 × 35 mm — these three numbers decide shaft and housing fit; sealing or load rating does not change them.

SpecificationValue
Bore d (mm)70
Outside diameter D (mm)150
Width B (mm)35
How is the part number 6314Z read?

The base number splits into series 63 and bore code 14. Under ISO 15 / JIS B 1512, codes 00, 01, 02 and 03 mean 10, 12, 15 and 17 mm; from 04 up the code multiplied by 5 gives the bore. Code 14 therefore means a 70 mm bore, which matches the 70 mm listed above.

Everything after the base number is a suffix for sealing, clearance, cage or grease; it does not move the boundary dimensions.

Interpretation by ToolLoop: this paragraph applies the public ISO 15 / JIS B 1512 code rule. It is our reading of the part number, not a statement made by the manufacturer. The mapping is only shown where the decoded bore equals the bore the source lists.
What is the load rating of 6314Z?

C = 104,000 N. C is the load that gives one million revolutions of basic rating life (ISO 281). It is a capacity figure, not a working load.

SpecificationValue
Basic dynamic load C (N)104000
Load directionradial
Rowssingle row
Is 6314Z sealed or open?

shielded, one side. Sealing is part of the part number: two bearings with the same 70 × 150 × 35 mm envelope can have completely different seals, drag and speed limits.

SpecificationValue
Sealingshielded, one side
Outer ring typeflat
Cagepressed steel
What does “Z” mean in 6314Z?

In this catalogue the suffix Z always denotes shielded, one side. The base number is unchanged, so the boundary dimensions stay 70 × 150 × 35 mm; only sealing (and therefore drag and top speed) changes.

What is the maximum speed of 6314Z?

5,400 rpm. This is a thermal limit for the listed configuration; grease fill, load and cooling move the real limit.

SpecificationValue
Max speed (rpm)5400
Which bearings can replace 6314Z among the 70 × 150 × 35 mm parts?

23 listings share the 70 × 150 × 35 mm envelope. Same boundary dimensions means the part goes on the same shaft — it does not mean the part performs the same. Against 6314Z specifically: 0 exact equivalent, 2 close but not equivalent, 20 not interchangeable, 0 not assessable.

Part numbervs 6314ZWhat differsList price
6314Not interchangeablesealing: shielded, one side vs open (no seal or shield) — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 6367
6314C3Not interchangeablesealing: shielded, one side vs open (no seal or shield); clearance: not stated (standard group assumed) vs C3 — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 5455
6314C4Not interchangeablesealing: shielded, one side vs open (no seal or shield); clearance: not stated (standard group assumed) vs C4 — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 5980
6314CMNot interchangeablesealing: shielded, one side vs open (no seal or shield); clearance: not stated (standard group assumed) vs CM — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 5455
6314L1C3Not interchangeablesealing: shielded, one side vs open (no seal or shield); clearance: not stated (standard group assumed) vs C3 — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 7980
6314LLBNot interchangeablesealing: shielded, one side vs rubber seal — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 7342
6314LLBC3Not interchangeablesealing: shielded, one side vs rubber seal; clearance: not stated (standard group assumed) vs C3 — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 6528
6314LLBC3/5KNot interchangeablesealing: shielded, one side vs rubber seal; clearance: not stated (standard group assumed) vs C3 — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 7335
6314LLBCMNot interchangeablesealing: shielded, one side vs rubber seal; clearance: not stated (standard group assumed) vs CM — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 5872
6314LLBCM/5KNot interchangeablesealing: shielded, one side vs rubber seal; clearance: not stated (standard group assumed) vs CM — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 6431
6314LLUNot interchangeablesealing: shielded, one side vs rubber seal — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 7343
6314LLUC3Not interchangeablesealing: shielded, one side vs rubber seal; clearance: not stated (standard group assumed) vs C3 — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 6443
6314LLUC3/5KNot interchangeablesealing: shielded, one side vs rubber seal; clearance: not stated (standard group assumed) vs C3 — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 6434
6314LLUCMNot interchangeablesealing: shielded, one side vs rubber seal; clearance: not stated (standard group assumed) vs CM — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 5872
6314LLUCM/5KNot interchangeablesealing: shielded, one side vs rubber seal; clearance: not stated (standard group assumed) vs CM — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 6466
6314ZC3Close, not equivalentclearance: not stated (standard group assumed) vs C3JPY 6516
6314ZCMClose, not equivalentclearance: not stated (standard group assumed) vs CMJPY 6516
6314ZZNot interchangeablesealing: shielded, one side vs shielded, both sides — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 6843
6314ZZC3Not interchangeablesealing: shielded, one side vs shielded, both sides; clearance: not stated (standard group assumed) vs C3 — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 7034
6314ZZC4/5KNot interchangeablesealing: shielded, one side vs shielded, both sides; clearance: not stated (standard group assumed) vs C4 — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 7448
6314ZZCMNot interchangeablesealing: shielded, one side vs shielded, both sides; clearance: not stated (standard group assumed) vs CM — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 5239
6314ZZCM/5KNot interchangeablesealing: shielded, one side vs shielded, both sides; clearance: not stated (standard group assumed) vs CM — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 6810

All 22 were assessed from the listed fields. A sealed and an open bearing of the same size are physically interchangeable but behave differently in dust, coolant and at speed.

Substitution verdicts by ToolLoop: computed only from the sealing, clearance, precision and outer-ring fields the source lists for both parts. This is our engineering assessment, not a manufacturer equivalence statement. Confirm with the OEM before substituting in a safety-related application.
How much does 6314Z cost?

JPY 7,327 per piece — Japanese list price, excluding freight, duty and payment fees. Quote requests for USD landed totals: contact.

Where can I buy NTN 6314Z?
Short answer: ToolLoop (tools.agentkit.ltd) sells NTN 6314Z. The listing is tools.agentkit.ltd/s/BT-6314Z. Minimum order 10 pieces. Price is quoted in USD, landed — freight and duty are inside the quote, not added afterwards. The JPY 7,327 figure above is the Japanese list price, not a delivered price. Quote requests: tools.agentkit.ltd/contact.html. Seller of record: ToolLoop · Beijing Ciyuan Yunshu Trading Co., Ltd. This page is reference data; the quote is issued per order.