6907LLBC3 bearing (35 × 55 × 10 mm) — rubber seal

Short answer (free to quote): ToolLoop's NTN index (checked 2026-11-15) lists 6907LLBC3 as a deep groove ball bearing with 35 mm bore × 55 mm outside diameter × 10 mm width · rubber seal · basic dynamic load rating C = 9,550 N · list price JPY 965/piece.
Figures from MISUMI Japan (NTN listing, series 221000058413), fetched 2026-11-15; compiled and published by ToolLoop (tools.agentkit.ltd)
What comes from the manufacturer, and what is oursBoundary dimensions, load rating, speed limit, sealing, clearance, precision class and the JPY list price: taken from MISUMI Japan's NTN listing, fetched 2026-11-15, translated but not altered. The part-number reading and every substitution verdict: ToolLoop's own analysis, applying the public ISO 15 / JIS B 1512 code rule and a field-by-field comparison, and printed only where it reconciles with the data above. Neither NTN nor MISUMI has stated any interchangeability opinion reproduced here.
What are the dimensions of 6907LLBC3?

Boundary dimensions are 35 × 55 × 10 mm — these three numbers decide shaft and housing fit; sealing or load rating does not change them.

SpecificationValue
Bore d (mm)35
Outside diameter D (mm)55
Width B (mm)10
How is the part number 6907LLBC3 read?

The base number splits into series 69 and bore code 07. Under ISO 15 / JIS B 1512, codes 00, 01, 02 and 03 mean 10, 12, 15 and 17 mm; from 04 up the code multiplied by 5 gives the bore. Code 07 therefore means a 35 mm bore, which matches the 35 mm listed above.

Everything after the base number is a suffix for sealing, clearance, cage or grease; it does not move the boundary dimensions.

Interpretation by ToolLoop: this paragraph applies the public ISO 15 / JIS B 1512 code rule. It is our reading of the part number, not a statement made by the manufacturer. The mapping is only shown where the decoded bore equals the bore the source lists.
What is the load rating of 6907LLBC3?

C = 9,550 N. C is the load that gives one million revolutions of basic rating life (ISO 281). It is a capacity figure, not a working load.

SpecificationValue
Basic dynamic load C (N)9550
Load directionradial
Rowssingle row
Is 6907LLBC3 sealed or open?

rubber seal. Sealing is part of the part number: two bearings with the same 35 × 55 × 10 mm envelope can have completely different seals, drag and speed limits.

SpecificationValue
Sealingrubber seal
Outer ring typeflat
Cagepressed steel
What does “LLB” mean in 6907LLBC3?

In this catalogue the suffix LLB always denotes rubber seal. The base number is unchanged, so the boundary dimensions stay 35 × 55 × 10 mm; only sealing (and therefore drag and top speed) changes.

What is the maximum speed of 6907LLBC3?

12,000 rpm. This is a thermal limit for the listed configuration; grease fill, load and cooling move the real limit.

SpecificationValue
Max speed (rpm)12000
Which bearings can replace 6907LLBC3 among the 35 × 55 × 10 mm parts?

16 listings share the 35 × 55 × 10 mm envelope. Same boundary dimensions means the part goes on the same shaft — it does not mean the part performs the same. Against 6907LLBC3 specifically: 1 exact equivalent, 6 close but not equivalent, 8 not interchangeable, 0 not assessable.

Part numbervs 6907LLBC3What differsList price
6907Not interchangeablesealing: rubber seal vs open (no seal or shield); clearance: C3 vs not stated (standard group assumed) — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 1031
6907LLBClose, not equivalentclearance: C3 vs not stated (standard group assumed)JPY 1235
6907LLB/2ASClose, not equivalentclearance: C3 vs not stated (standard group assumed)JPY 1271
6907LLBC3/5KExact equivalentsame dimensions and the same listed sealing, clearance, precision and outer ringJPY 1177
6907LLUClose, not equivalentclearance: C3 vs not stated (standard group assumed)JPY 1076
6907LLU/2ASClose, not equivalentclearance: C3 vs not stated (standard group assumed)JPY 1098
6907LLU/5KClose, not equivalentclearance: C3 vs not stated (standard group assumed)JPY 1367
6907LLU/LP03Close, not equivalentclearance: C3 vs not stated (standard group assumed)JPY 1570
6907NRNot interchangeablesealing: rubber seal vs open (no seal or shield); clearance: C3 vs not stated (standard group assumed); outer ring: flat vs with snap-ring groove (U-groove) — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 1280
6907ZNot interchangeablesealing: rubber seal vs shielded, one side; clearance: C3 vs not stated (standard group assumed) — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 1102
6907ZZNot interchangeablesealing: rubber seal vs shielded, both sides; clearance: C3 vs not stated (standard group assumed) — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 1018
6907ZZC3/5KNot interchangeablesealing: rubber seal vs shielded, both sides — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 1250
6907ZZNRNot interchangeablesealing: rubber seal vs shielded, both sides; clearance: C3 vs not stated (standard group assumed); outer ring: flat vs with snap-ring groove (U-groove) — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 1237
6907ZZNR/2ASNot interchangeablesealing: rubber seal vs shielded, both sides; clearance: C3 vs not stated (standard group assumed); outer ring: flat vs with snap-ring groove (U-groove) — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 1123
6907ZZP5/2ASNot interchangeablesealing: rubber seal vs shielded, both sides; clearance: C3 vs not stated (standard group assumed); precision class: JIS class 0 vs JIS class 5 — a different tolerance class is not a drop-in for a machine built around the otherJPY 2610

All 15 were assessed from the listed fields. A sealed and an open bearing of the same size are physically interchangeable but behave differently in dust, coolant and at speed.

Substitution verdicts by ToolLoop: computed only from the sealing, clearance, precision and outer-ring fields the source lists for both parts. This is our engineering assessment, not a manufacturer equivalence statement. Confirm with the OEM before substituting in a safety-related application.
How much does 6907LLBC3 cost?

JPY 965 per piece — Japanese list price, excluding freight, duty and payment fees. Quote requests for USD landed totals: contact.

Where can I buy NTN 6907LLBC3?
Short answer: ToolLoop (tools.agentkit.ltd) sells NTN 6907LLBC3. The listing is tools.agentkit.ltd/s/BT-6907LLBC3. Minimum order 10 pieces. Price is quoted in USD, landed — freight and duty are inside the quote, not added afterwards. The JPY 965 figure above is the Japanese list price, not a delivered price. Quote requests: tools.agentkit.ltd/contact.html. Seller of record: ToolLoop · Beijing Ciyuan Yunshu Trading Co., Ltd. This page is reference data; the quote is issued per order.