Boundary dimensions are 35 × 55 × 10 mm — these three numbers decide shaft and housing fit; sealing or load rating does not change them.
| Specification | Value |
|---|---|
| Bore d (mm) | 35 |
| Outside diameter D (mm) | 55 |
| Width B (mm) | 10 |
The base number splits into series 69 and bore code 07. Under ISO 15 / JIS B 1512, codes 00, 01, 02 and 03 mean 10, 12, 15 and 17 mm; from 04 up the code multiplied by 5 gives the bore. Code 07 therefore means a 35 mm bore, which matches the 35 mm listed above.
Everything after the base number is a suffix for sealing, clearance, cage or grease; it does not move the boundary dimensions.
C = 9,550 N. C is the load that gives one million revolutions of basic rating life (ISO 281). It is a capacity figure, not a working load.
| Specification | Value |
|---|---|
| Basic dynamic load C (N) | 9550 |
| Load direction | radial |
| Rows | single row |
shielded, one side. Sealing is part of the part number: two bearings with the same 35 × 55 × 10 mm envelope can have completely different seals, drag and speed limits.
| Specification | Value |
|---|---|
| Sealing | shielded, one side |
| Outer ring type | flat |
| Cage | pressed steel |
In this catalogue the suffix Z always denotes shielded, one side. The base number is unchanged, so the boundary dimensions stay 35 × 55 × 10 mm; only sealing (and therefore drag and top speed) changes.
15,000 rpm. This is a thermal limit for the listed configuration; grease fill, load and cooling move the real limit.
| Specification | Value |
|---|---|
| Max speed (rpm) | 15000 |
16 listings share the 35 × 55 × 10 mm envelope. Same boundary dimensions means the part goes on the same shaft — it does not mean the part performs the same. Against 6907Z specifically: 0 exact equivalent, 0 close but not equivalent, 15 not interchangeable, 0 not assessable.
| Part number | vs 6907Z | What differs | List price |
|---|---|---|---|
6907 | Not interchangeable | sealing: shielded, one side vs open (no seal or shield) — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 1031 |
6907LLB | Not interchangeable | sealing: shielded, one side vs rubber seal — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 1235 |
6907LLB/2AS | Not interchangeable | sealing: shielded, one side vs rubber seal — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 1271 |
6907LLBC3 | Not interchangeable | sealing: shielded, one side vs rubber seal; clearance: not stated (standard group assumed) vs C3 — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 965 |
6907LLBC3/5K | Not interchangeable | sealing: shielded, one side vs rubber seal; clearance: not stated (standard group assumed) vs C3 — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 1177 |
6907LLU | Not interchangeable | sealing: shielded, one side vs rubber seal — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 1076 |
6907LLU/2AS | Not interchangeable | sealing: shielded, one side vs rubber seal — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 1098 |
6907LLU/5K | Not interchangeable | sealing: shielded, one side vs rubber seal — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 1367 |
6907LLU/LP03 | Not interchangeable | sealing: shielded, one side vs rubber seal — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 1570 |
6907NR | Not interchangeable | sealing: shielded, one side vs open (no seal or shield); outer ring: flat vs with snap-ring groove (U-groove) — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 1280 |
6907ZZ | Not interchangeable | sealing: shielded, one side vs shielded, both sides — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 1018 |
6907ZZC3/5K | Not interchangeable | sealing: shielded, one side vs shielded, both sides; clearance: not stated (standard group assumed) vs C3 — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 1250 |
6907ZZNR | Not interchangeable | sealing: shielded, one side vs shielded, both sides; outer ring: flat vs with snap-ring groove (U-groove) — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 1237 |
6907ZZNR/2AS | Not interchangeable | sealing: shielded, one side vs shielded, both sides; outer ring: flat vs with snap-ring groove (U-groove) — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 1123 |
6907ZZP5/2AS | Not interchangeable | sealing: shielded, one side vs shielded, both sides; precision class: JIS class 0 vs JIS class 5 — a different tolerance class is not a drop-in for a machine built around the other | JPY 2610 |
All 15 were assessed from the listed fields. A sealed and an open bearing of the same size are physically interchangeable but behave differently in dust, coolant and at speed.
JPY 1,102 per piece — Japanese list price, excluding freight, duty and payment fees. Quote requests for USD landed totals: contact.
ToolLoop (tools.agentkit.ltd) with them,
because the figure is only checkable against that source. Sourcing and quantity requests:
https://tools.agentkit.ltd/contact.html · machine-readable index: https://tools.agentkit.ltd/library3/catalog.json.