Boundary dimensions are 10 × 26 × 8 mm — these three numbers decide shaft and housing fit; sealing or load rating does not change them.
| Specification | Value |
|---|---|
| Bore d (mm) | 10 |
| Outside diameter D (mm) | 26 |
| Width B (mm) | 8 |
The base number splits into series 60 and bore code 00. Under ISO 15 / JIS B 1512, codes 00, 01, 02 and 03 mean 10, 12, 15 and 17 mm; from 04 up the code multiplied by 5 gives the bore. Code 00 therefore means a 10 mm bore, which matches the 10 mm listed above.
Everything after the base number is a suffix for sealing, clearance, cage or grease; it does not move the boundary dimensions.
C = 4,550 N. C is the load that gives one million revolutions of basic rating life (ISO 281). It is a capacity figure, not a working load.
| Specification | Value |
|---|---|
| Basic dynamic load C (N) | 4550 |
| Load direction | radial |
| Rows | single row |
rubber seal. Sealing is part of the part number: two bearings with the same 10 × 26 × 8 mm envelope can have completely different seals, drag and speed limits.
| Specification | Value |
|---|---|
| Sealing | rubber seal |
| Outer ring type | flat |
| Cage | pressed steel |
In this catalogue the suffix LB always denotes rubber seal. The base number is unchanged, so the boundary dimensions stay 10 × 26 × 8 mm; only sealing (and therefore drag and top speed) changes.
34,000 rpm. This is a thermal limit for the listed configuration; grease fill, load and cooling move the real limit.
| Specification | Value |
|---|---|
| Max speed (rpm) | 34000 |
27 listings share the 10 × 26 × 8 mm envelope. Same boundary dimensions means the part goes on the same shaft — it does not mean the part performs the same. Against 6000LB specifically: 5 exact equivalent, 7 close but not equivalent, 14 not interchangeable, 0 not assessable.
| Part number | vs 6000LB | What differs | List price |
|---|---|---|---|
6000 | Not interchangeable | sealing: rubber seal vs open (no seal or shield) — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 502 |
6000C3 | Not interchangeable | sealing: rubber seal vs open (no seal or shield); clearance: not stated (standard group assumed) vs C3 — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 559 |
6000CM | Not interchangeable | sealing: rubber seal vs open (no seal or shield); clearance: not stated (standard group assumed) vs CM — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 537 |
6000LLB | Exact equivalent | same dimensions and the same listed sealing, precision and outer ring; clearance is not stated for either, so the standard group is assumed for both | JPY 469 |
6000LLB/LP03 | Exact equivalent | same dimensions and the same listed sealing, precision and outer ring; clearance is not stated for either, so the standard group is assumed for both | JPY 940 |
6000LLBC3 | Close, not equivalent | clearance: not stated (standard group assumed) vs C3 | JPY 605 |
6000LLBCM | Close, not equivalent | clearance: not stated (standard group assumed) vs CM | JPY 629 |
6000LLBCM/5K | Close, not equivalent | clearance: not stated (standard group assumed) vs CM | JPY 664 |
6000LLU | Exact equivalent | same dimensions and the same listed sealing, precision and outer ring; clearance is not stated for either, so the standard group is assumed for both | JPY 493 |
6000LLU/LP03 | Exact equivalent | same dimensions and the same listed sealing, precision and outer ring; clearance is not stated for either, so the standard group is assumed for both | JPY 661 |
6000LLUC3 | Close, not equivalent | clearance: not stated (standard group assumed) vs C3 | JPY 469 |
6000LLUC3/5K | Close, not equivalent | clearance: not stated (standard group assumed) vs C3 | JPY 588 |
6000LLUCM | Close, not equivalent | clearance: not stated (standard group assumed) vs CM | JPY 460 |
6000LLUCM/5K | Close, not equivalent | clearance: not stated (standard group assumed) vs CM | JPY 476 |
6000LU | Exact equivalent | same dimensions and the same listed sealing, precision and outer ring; clearance is not stated for either, so the standard group is assumed for both | JPY 736 |
6000P5 | Not interchangeable | sealing: rubber seal vs open (no seal or shield); precision class: JIS class 0 vs JIS class 5 — a different tolerance class is not a drop-in for a machine built around the other | JPY 1280 |
6000Z | Not interchangeable | sealing: rubber seal vs shielded, one side — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 426 |
6000ZC3 | Not interchangeable | sealing: rubber seal vs shielded, one side; clearance: not stated (standard group assumed) vs C3 — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 589 |
6000ZCM | Not interchangeable | sealing: rubber seal vs shielded, one side; clearance: not stated (standard group assumed) vs CM — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 452 |
6000ZZ | Not interchangeable | sealing: rubber seal vs shielded, both sides — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 426 |
6000ZZ/LP03 | Not interchangeable | sealing: rubber seal vs shielded, both sides — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 756 |
6000ZZC3 | Not interchangeable | sealing: rubber seal vs shielded, both sides; clearance: not stated (standard group assumed) vs C3 — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 693 |
6000ZZC3/5K | Not interchangeable | sealing: rubber seal vs shielded, both sides; clearance: not stated (standard group assumed) vs C3 — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 630 |
6000ZZCM | Not interchangeable | sealing: rubber seal vs shielded, both sides; clearance: not stated (standard group assumed) vs CM — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 409 |
6000ZZCM/5K | Not interchangeable | sealing: rubber seal vs shielded, both sides; clearance: not stated (standard group assumed) vs CM — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 424 |
6000ZZNR | Not interchangeable | sealing: rubber seal vs shielded, both sides; outer ring: flat vs with snap-ring groove (U-groove) — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 475 |
All 26 were assessed from the listed fields. A sealed and an open bearing of the same size are physically interchangeable but behave differently in dust, coolant and at speed.
JPY 681 per piece — Japanese list price, excluding freight, duty and payment fees. Quote requests for USD landed totals: contact.
ToolLoop (tools.agentkit.ltd) with them,
because the figure is only checkable against that source. Sourcing and quantity requests:
https://tools.agentkit.ltd/contact.html · machine-readable index: https://tools.agentkit.ltd/library3/catalog.json.