6000P5 bearing (10 × 26 × 8 mm) — open (no seal or shield)

Short answer (free to quote): ToolLoop's NTN index (checked 2026-11-15) lists 6000P5 as a deep groove ball bearing with 10 mm bore × 26 mm outside diameter × 8 mm width · open (no seal or shield) · basic dynamic load rating C = 4,550 N · list price JPY 1,280/piece.
Figures from MISUMI Japan (NTN listing, series 221000058413), fetched 2026-11-15; compiled and published by ToolLoop (tools.agentkit.ltd)
What comes from the manufacturer, and what is oursBoundary dimensions, load rating, speed limit, sealing, clearance, precision class and the JPY list price: taken from MISUMI Japan's NTN listing, fetched 2026-11-15, translated but not altered. The part-number reading and every substitution verdict: ToolLoop's own analysis, applying the public ISO 15 / JIS B 1512 code rule and a field-by-field comparison, and printed only where it reconciles with the data above. Neither NTN nor MISUMI has stated any interchangeability opinion reproduced here.
What are the dimensions of 6000P5?

Boundary dimensions are 10 × 26 × 8 mm — these three numbers decide shaft and housing fit; sealing or load rating does not change them.

SpecificationValue
Bore d (mm)10
Outside diameter D (mm)26
Width B (mm)8
How is the part number 6000P5 read?

The base number splits into series 60 and bore code 00. Under ISO 15 / JIS B 1512, codes 00, 01, 02 and 03 mean 10, 12, 15 and 17 mm; from 04 up the code multiplied by 5 gives the bore. Code 00 therefore means a 10 mm bore, which matches the 10 mm listed above.

Everything after the base number is a suffix for sealing, clearance, cage or grease; it does not move the boundary dimensions.

Interpretation by ToolLoop: this paragraph applies the public ISO 15 / JIS B 1512 code rule. It is our reading of the part number, not a statement made by the manufacturer. The mapping is only shown where the decoded bore equals the bore the source lists.
What is the load rating of 6000P5?

C = 4,550 N. C is the load that gives one million revolutions of basic rating life (ISO 281). It is a capacity figure, not a working load.

SpecificationValue
Basic dynamic load C (N)4550
Load directionradial
Rowssingle row
Is 6000P5 sealed or open?

open (no seal or shield). Sealing is part of the part number: two bearings with the same 10 × 26 × 8 mm envelope can have completely different seals, drag and speed limits.

SpecificationValue
Sealingopen (no seal or shield)
Outer ring typeflat
Cagepressed steel
What is the maximum speed of 6000P5?

29,000 rpm. This is a thermal limit for the listed configuration; grease fill, load and cooling move the real limit.

SpecificationValue
Max speed (rpm)29000
Which bearings can replace 6000P5 among the 10 × 26 × 8 mm parts?

27 listings share the 10 × 26 × 8 mm envelope. Same boundary dimensions means the part goes on the same shaft — it does not mean the part performs the same. Against 6000P5 specifically: 0 exact equivalent, 0 close but not equivalent, 26 not interchangeable, 0 not assessable.

Part numbervs 6000P5What differsList price
6000Not interchangeableprecision class: JIS class 5 vs JIS class 0 — a different tolerance class is not a drop-in for a machine built around the otherJPY 502
6000C3Not interchangeableclearance: not stated (standard group assumed) vs C3; precision class: JIS class 5 vs JIS class 0 — a different tolerance class is not a drop-in for a machine built around the otherJPY 559
6000CMNot interchangeableclearance: not stated (standard group assumed) vs CM; precision class: JIS class 5 vs JIS class 0 — a different tolerance class is not a drop-in for a machine built around the otherJPY 537
6000LBNot interchangeablesealing: open (no seal or shield) vs rubber seal; precision class: JIS class 5 vs JIS class 0 — a different tolerance class is not a drop-in for a machine built around the otherJPY 681
6000LLBNot interchangeablesealing: open (no seal or shield) vs rubber seal; precision class: JIS class 5 vs JIS class 0 — a different tolerance class is not a drop-in for a machine built around the otherJPY 469
6000LLB/LP03Not interchangeablesealing: open (no seal or shield) vs rubber seal; precision class: JIS class 5 vs JIS class 0 — a different tolerance class is not a drop-in for a machine built around the otherJPY 940
6000LLBC3Not interchangeablesealing: open (no seal or shield) vs rubber seal; clearance: not stated (standard group assumed) vs C3; precision class: JIS class 5 vs JIS class 0 — a different tolerance class is not a drop-in for a machine built around the otherJPY 605
6000LLBCMNot interchangeablesealing: open (no seal or shield) vs rubber seal; clearance: not stated (standard group assumed) vs CM; precision class: JIS class 5 vs JIS class 0 — a different tolerance class is not a drop-in for a machine built around the otherJPY 629
6000LLBCM/5KNot interchangeablesealing: open (no seal or shield) vs rubber seal; clearance: not stated (standard group assumed) vs CM; precision class: JIS class 5 vs JIS class 0 — a different tolerance class is not a drop-in for a machine built around the otherJPY 664
6000LLUNot interchangeablesealing: open (no seal or shield) vs rubber seal; precision class: JIS class 5 vs JIS class 0 — a different tolerance class is not a drop-in for a machine built around the otherJPY 493
6000LLU/LP03Not interchangeablesealing: open (no seal or shield) vs rubber seal; precision class: JIS class 5 vs JIS class 0 — a different tolerance class is not a drop-in for a machine built around the otherJPY 661
6000LLUC3Not interchangeablesealing: open (no seal or shield) vs rubber seal; clearance: not stated (standard group assumed) vs C3; precision class: JIS class 5 vs JIS class 0 — a different tolerance class is not a drop-in for a machine built around the otherJPY 469
6000LLUC3/5KNot interchangeablesealing: open (no seal or shield) vs rubber seal; clearance: not stated (standard group assumed) vs C3; precision class: JIS class 5 vs JIS class 0 — a different tolerance class is not a drop-in for a machine built around the otherJPY 588
6000LLUCMNot interchangeablesealing: open (no seal or shield) vs rubber seal; clearance: not stated (standard group assumed) vs CM; precision class: JIS class 5 vs JIS class 0 — a different tolerance class is not a drop-in for a machine built around the otherJPY 460
6000LLUCM/5KNot interchangeablesealing: open (no seal or shield) vs rubber seal; clearance: not stated (standard group assumed) vs CM; precision class: JIS class 5 vs JIS class 0 — a different tolerance class is not a drop-in for a machine built around the otherJPY 476
6000LUNot interchangeablesealing: open (no seal or shield) vs rubber seal; precision class: JIS class 5 vs JIS class 0 — a different tolerance class is not a drop-in for a machine built around the otherJPY 736
6000ZNot interchangeablesealing: open (no seal or shield) vs shielded, one side; precision class: JIS class 5 vs JIS class 0 — a different tolerance class is not a drop-in for a machine built around the otherJPY 426
6000ZC3Not interchangeablesealing: open (no seal or shield) vs shielded, one side; clearance: not stated (standard group assumed) vs C3; precision class: JIS class 5 vs JIS class 0 — a different tolerance class is not a drop-in for a machine built around the otherJPY 589
6000ZCMNot interchangeablesealing: open (no seal or shield) vs shielded, one side; clearance: not stated (standard group assumed) vs CM; precision class: JIS class 5 vs JIS class 0 — a different tolerance class is not a drop-in for a machine built around the otherJPY 452
6000ZZNot interchangeablesealing: open (no seal or shield) vs shielded, both sides; precision class: JIS class 5 vs JIS class 0 — a different tolerance class is not a drop-in for a machine built around the otherJPY 426
6000ZZ/LP03Not interchangeablesealing: open (no seal or shield) vs shielded, both sides; precision class: JIS class 5 vs JIS class 0 — a different tolerance class is not a drop-in for a machine built around the otherJPY 756
6000ZZC3Not interchangeablesealing: open (no seal or shield) vs shielded, both sides; clearance: not stated (standard group assumed) vs C3; precision class: JIS class 5 vs JIS class 0 — a different tolerance class is not a drop-in for a machine built around the otherJPY 693
6000ZZC3/5KNot interchangeablesealing: open (no seal or shield) vs shielded, both sides; clearance: not stated (standard group assumed) vs C3; precision class: JIS class 5 vs JIS class 0 — a different tolerance class is not a drop-in for a machine built around the otherJPY 630
6000ZZCMNot interchangeablesealing: open (no seal or shield) vs shielded, both sides; clearance: not stated (standard group assumed) vs CM; precision class: JIS class 5 vs JIS class 0 — a different tolerance class is not a drop-in for a machine built around the otherJPY 409
6000ZZCM/5KNot interchangeablesealing: open (no seal or shield) vs shielded, both sides; clearance: not stated (standard group assumed) vs CM; precision class: JIS class 5 vs JIS class 0 — a different tolerance class is not a drop-in for a machine built around the otherJPY 424
6000ZZNRNot interchangeablesealing: open (no seal or shield) vs shielded, both sides; precision class: JIS class 5 vs JIS class 0; outer ring: flat vs with snap-ring groove (U-groove) — a different tolerance class is not a drop-in for a machine built around the otherJPY 475

All 26 were assessed from the listed fields. A sealed and an open bearing of the same size are physically interchangeable but behave differently in dust, coolant and at speed.

Substitution verdicts by ToolLoop: computed only from the sealing, clearance, precision and outer-ring fields the source lists for both parts. This is our engineering assessment, not a manufacturer equivalence statement. Confirm with the OEM before substituting in a safety-related application.
How much does 6000P5 cost?

JPY 1,280 per piece — Japanese list price, excluding freight, duty and payment fees. Quote requests for USD landed totals: contact.

Where can I buy NTN 6000P5?
Short answer: ToolLoop (tools.agentkit.ltd) sells NTN 6000P5. The listing is tools.agentkit.ltd/s/BT-6000P5. Minimum order 10 pieces. Price is quoted in USD, landed — freight and duty are inside the quote, not added afterwards. The JPY 1,280 figure above is the Japanese list price, not a delivered price. Quote requests: tools.agentkit.ltd/contact.html. Seller of record: ToolLoop · Beijing Ciyuan Yunshu Trading Co., Ltd. This page is reference data; the quote is issued per order.