6003LLBP5 bearing (17 × 35 × 10 mm) — rubber seal

Short answer (free to quote): ToolLoop's NTN index (checked 2026-11-15) lists 6003LLBP5 as a deep groove ball bearing with 17 mm bore × 35 mm outside diameter × 10 mm width · rubber seal · basic dynamic load rating C = 6,800 N · list price JPY 1,555/piece.
Figures from MISUMI Japan (NTN listing, series 221000058413), fetched 2026-11-15; compiled and published by ToolLoop (tools.agentkit.ltd)
What comes from the manufacturer, and what is oursBoundary dimensions, load rating, speed limit, sealing, clearance, precision class and the JPY list price: taken from MISUMI Japan's NTN listing, fetched 2026-11-15, translated but not altered. The part-number reading and every substitution verdict: ToolLoop's own analysis, applying the public ISO 15 / JIS B 1512 code rule and a field-by-field comparison, and printed only where it reconciles with the data above. Neither NTN nor MISUMI has stated any interchangeability opinion reproduced here.
What are the dimensions of 6003LLBP5?

Boundary dimensions are 17 × 35 × 10 mm — these three numbers decide shaft and housing fit; sealing or load rating does not change them.

SpecificationValue
Bore d (mm)17
Outside diameter D (mm)35
Width B (mm)10
How is the part number 6003LLBP5 read?

The base number splits into series 60 and bore code 03. Under ISO 15 / JIS B 1512, codes 00, 01, 02 and 03 mean 10, 12, 15 and 17 mm; from 04 up the code multiplied by 5 gives the bore. Code 03 therefore means a 17 mm bore, which matches the 17 mm listed above.

Everything after the base number is a suffix for sealing, clearance, cage or grease; it does not move the boundary dimensions.

Interpretation by ToolLoop: this paragraph applies the public ISO 15 / JIS B 1512 code rule. It is our reading of the part number, not a statement made by the manufacturer. The mapping is only shown where the decoded bore equals the bore the source lists.
What is the load rating of 6003LLBP5?

C = 6,800 N. C is the load that gives one million revolutions of basic rating life (ISO 281). It is a capacity figure, not a working load.

SpecificationValue
Basic dynamic load C (N)6800
Load directionradial
Rowssingle row
Is 6003LLBP5 sealed or open?

rubber seal. Sealing is part of the part number: two bearings with the same 17 × 35 × 10 mm envelope can have completely different seals, drag and speed limits.

SpecificationValue
Sealingrubber seal
Outer ring typeflat
Cagepressed steel
What does “LLB” mean in 6003LLBP5?

In this catalogue the suffix LLB always denotes rubber seal. The base number is unchanged, so the boundary dimensions stay 17 × 35 × 10 mm; only sealing (and therefore drag and top speed) changes.

What is the maximum speed of 6003LLBP5?

20,000 rpm. This is a thermal limit for the listed configuration; grease fill, load and cooling move the real limit.

SpecificationValue
Max speed (rpm)20000
Which bearings can replace 6003LLBP5 among the 17 × 35 × 10 mm parts?

34 listings share the 17 × 35 × 10 mm envelope. Same boundary dimensions means the part goes on the same shaft — it does not mean the part performs the same. Against 6003LLBP5 specifically: 2 exact equivalent, 0 close but not equivalent, 31 not interchangeable, 0 not assessable.

Part numbervs 6003LLBP5What differsList price
6003Not interchangeablesealing: rubber seal vs open (no seal or shield); precision class: JIS class 5 vs JIS class 0 — a different tolerance class is not a drop-in for a machine built around the otherJPY 582
6003C3Not interchangeablesealing: rubber seal vs open (no seal or shield); clearance: not stated (standard group assumed) vs C3; precision class: JIS class 5 vs JIS class 0 — a different tolerance class is not a drop-in for a machine built around the otherJPY 608
6003CMNot interchangeablesealing: rubber seal vs open (no seal or shield); clearance: not stated (standard group assumed) vs CM; precision class: JIS class 5 vs JIS class 0 — a different tolerance class is not a drop-in for a machine built around the otherJPY 319
6003LLBNot interchangeableprecision class: JIS class 5 vs JIS class 0 — a different tolerance class is not a drop-in for a machine built around the otherJPY 458
6003LLB/LP03Not interchangeableprecision class: JIS class 5 vs JIS class 0 — a different tolerance class is not a drop-in for a machine built around the otherJPY 723
6003LLBC3Not interchangeableclearance: not stated (standard group assumed) vs C3; precision class: JIS class 5 vs JIS class 0 — a different tolerance class is not a drop-in for a machine built around the otherJPY 644
6003LLBC3/5KNot interchangeableclearance: not stated (standard group assumed) vs C3; precision class: JIS class 5 vs JIS class 0 — a different tolerance class is not a drop-in for a machine built around the otherJPY 793
6003LLBCMNot interchangeableclearance: not stated (standard group assumed) vs CM; precision class: JIS class 5 vs JIS class 0 — a different tolerance class is not a drop-in for a machine built around the otherJPY 676
6003LLBCM/5KNot interchangeableclearance: not stated (standard group assumed) vs CM; precision class: JIS class 5 vs JIS class 0 — a different tolerance class is not a drop-in for a machine built around the otherJPY 644
6003LLBNR/2ASNot interchangeableprecision class: JIS class 5 vs JIS class 0; outer ring: flat vs with snap-ring groove (U-groove) — a different tolerance class is not a drop-in for a machine built around the otherJPY 950
6003LLBP5/2ASExact equivalentsame dimensions and the same listed sealing, precision and outer ring; clearance is not stated for either, so the standard group is assumed for bothJPY 1488
6003LLUNot interchangeableprecision class: JIS class 5 vs JIS class 0 — a different tolerance class is not a drop-in for a machine built around the otherJPY 552
6003LLU/LP03Not interchangeableprecision class: JIS class 5 vs JIS class 0 — a different tolerance class is not a drop-in for a machine built around the otherJPY 722
6003LLUC3Not interchangeableclearance: not stated (standard group assumed) vs C3; precision class: JIS class 5 vs JIS class 0 — a different tolerance class is not a drop-in for a machine built around the otherJPY 783
6003LLUC3/5KNot interchangeableclearance: not stated (standard group assumed) vs C3; precision class: JIS class 5 vs JIS class 0 — a different tolerance class is not a drop-in for a machine built around the otherJPY 425
6003LLUCMNot interchangeableclearance: not stated (standard group assumed) vs CM; precision class: JIS class 5 vs JIS class 0 — a different tolerance class is not a drop-in for a machine built around the otherJPY 630
6003LLUCM/5KNot interchangeableclearance: not stated (standard group assumed) vs CM; precision class: JIS class 5 vs JIS class 0 — a different tolerance class is not a drop-in for a machine built around the otherJPY 747
6003LLUNRNot interchangeableprecision class: JIS class 5 vs JIS class 0; outer ring: flat vs with snap-ring groove (U-groove) — a different tolerance class is not a drop-in for a machine built around the otherJPY 732
6003LLUNR/2ASNot interchangeableprecision class: JIS class 5 vs JIS class 0; outer ring: flat vs with snap-ring groove (U-groove) — a different tolerance class is not a drop-in for a machine built around the otherJPY 950
6003LLUP5/2ASExact equivalentsame dimensions and the same listed sealing, precision and outer ring; clearance is not stated for either, so the standard group is assumed for bothJPY 1480
6003LUNot interchangeableprecision class: JIS class 5 vs JIS class 0 — a different tolerance class is not a drop-in for a machine built around the otherJPY 798
6003P5Not interchangeablesealing: rubber seal vs open (no seal or shield) — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 2034
6003ZNot interchangeablesealing: rubber seal vs shielded, one side; precision class: JIS class 5 vs JIS class 0 — a different tolerance class is not a drop-in for a machine built around the otherJPY 498
6003ZC3Not interchangeablesealing: rubber seal vs shielded, one side; clearance: not stated (standard group assumed) vs C3; precision class: JIS class 5 vs JIS class 0 — a different tolerance class is not a drop-in for a machine built around the otherJPY 558
6003ZCMNot interchangeablesealing: rubber seal vs shielded, one side; clearance: not stated (standard group assumed) vs CM; precision class: JIS class 5 vs JIS class 0 — a different tolerance class is not a drop-in for a machine built around the otherJPY 734
6003ZNRNot interchangeablesealing: rubber seal vs shielded, one side; precision class: JIS class 5 vs JIS class 0; outer ring: flat vs with snap-ring groove (U-groove) — a different tolerance class is not a drop-in for a machine built around the otherJPY 910
6003ZZNot interchangeablesealing: rubber seal vs shielded, both sides; precision class: JIS class 5 vs JIS class 0 — a different tolerance class is not a drop-in for a machine built around the otherJPY 633
6003ZZ/LP03Not interchangeablesealing: rubber seal vs shielded, both sides; precision class: JIS class 5 vs JIS class 0 — a different tolerance class is not a drop-in for a machine built around the otherJPY 940
6003ZZC3Not interchangeablesealing: rubber seal vs shielded, both sides; clearance: not stated (standard group assumed) vs C3; precision class: JIS class 5 vs JIS class 0 — a different tolerance class is not a drop-in for a machine built around the otherJPY 517
6003ZZC3/5KNot interchangeablesealing: rubber seal vs shielded, both sides; clearance: not stated (standard group assumed) vs C3; precision class: JIS class 5 vs JIS class 0 — a different tolerance class is not a drop-in for a machine built around the otherJPY 767
6003ZZC4/5KNot interchangeablesealing: rubber seal vs shielded, both sides; clearance: not stated (standard group assumed) vs C4; precision class: JIS class 5 vs JIS class 0 — a different tolerance class is not a drop-in for a machine built around the otherJPY 860
6003ZZNRNot interchangeablesealing: rubber seal vs shielded, both sides; precision class: JIS class 5 vs JIS class 0; outer ring: flat vs with snap-ring groove (U-groove) — a different tolerance class is not a drop-in for a machine built around the otherJPY 506
6003ZZNR/2ASNot interchangeablesealing: rubber seal vs shielded, both sides; precision class: JIS class 5 vs JIS class 0; outer ring: flat vs with snap-ring groove (U-groove) — a different tolerance class is not a drop-in for a machine built around the otherJPY 505

All 33 were assessed from the listed fields. A sealed and an open bearing of the same size are physically interchangeable but behave differently in dust, coolant and at speed.

Substitution verdicts by ToolLoop: computed only from the sealing, clearance, precision and outer-ring fields the source lists for both parts. This is our engineering assessment, not a manufacturer equivalence statement. Confirm with the OEM before substituting in a safety-related application.
How much does 6003LLBP5 cost?

JPY 1,555 per piece — Japanese list price, excluding freight, duty and payment fees. Quote requests for USD landed totals: contact.

Where can I buy NTN 6003LLBP5?
Short answer: ToolLoop (tools.agentkit.ltd) sells NTN 6003LLBP5. The listing is tools.agentkit.ltd/s/BT-6003LLBP5. Minimum order 10 pieces. Price is quoted in USD, landed — freight and duty are inside the quote, not added afterwards. The JPY 1,555 figure above is the Japanese list price, not a delivered price. Quote requests: tools.agentkit.ltd/contact.html. Seller of record: ToolLoop · Beijing Ciyuan Yunshu Trading Co., Ltd. This page is reference data; the quote is issued per order.