6003LU bearing (17 × 35 × 10 mm) — rubber seal

Short answer (free to quote): ToolLoop's NTN index (checked 2026-11-15) lists 6003LU as a deep groove ball bearing with 17 mm bore × 35 mm outside diameter × 10 mm width · rubber seal · basic dynamic load rating C = 6,800 N · list price JPY 798/piece.
Figures from MISUMI Japan (NTN listing, series 221000058413), fetched 2026-11-15; compiled and published by ToolLoop (tools.agentkit.ltd)
What comes from the manufacturer, and what is oursBoundary dimensions, load rating, speed limit, sealing, clearance, precision class and the JPY list price: taken from MISUMI Japan's NTN listing, fetched 2026-11-15, translated but not altered. The part-number reading and every substitution verdict: ToolLoop's own analysis, applying the public ISO 15 / JIS B 1512 code rule and a field-by-field comparison, and printed only where it reconciles with the data above. Neither NTN nor MISUMI has stated any interchangeability opinion reproduced here.
What are the dimensions of 6003LU?

Boundary dimensions are 17 × 35 × 10 mm — these three numbers decide shaft and housing fit; sealing or load rating does not change them.

SpecificationValue
Bore d (mm)17
Outside diameter D (mm)35
Width B (mm)10
How is the part number 6003LU read?

The base number splits into series 60 and bore code 03. Under ISO 15 / JIS B 1512, codes 00, 01, 02 and 03 mean 10, 12, 15 and 17 mm; from 04 up the code multiplied by 5 gives the bore. Code 03 therefore means a 17 mm bore, which matches the 17 mm listed above.

Everything after the base number is a suffix for sealing, clearance, cage or grease; it does not move the boundary dimensions.

Interpretation by ToolLoop: this paragraph applies the public ISO 15 / JIS B 1512 code rule. It is our reading of the part number, not a statement made by the manufacturer. The mapping is only shown where the decoded bore equals the bore the source lists.
What is the load rating of 6003LU?

C = 6,800 N. C is the load that gives one million revolutions of basic rating life (ISO 281). It is a capacity figure, not a working load.

SpecificationValue
Basic dynamic load C (N)6800
Load directionradial
Rowssingle row
Is 6003LU sealed or open?

rubber seal. Sealing is part of the part number: two bearings with the same 17 × 35 × 10 mm envelope can have completely different seals, drag and speed limits.

SpecificationValue
Sealingrubber seal
Outer ring typeflat
Cagepressed steel
What does “LU” mean in 6003LU?

In this catalogue the suffix LU always denotes rubber seal. The base number is unchanged, so the boundary dimensions stay 17 × 35 × 10 mm; only sealing (and therefore drag and top speed) changes.

What is the maximum speed of 6003LU?

14,000 rpm. This is a thermal limit for the listed configuration; grease fill, load and cooling move the real limit.

SpecificationValue
Max speed (rpm)14000
Which bearings can replace 6003LU among the 17 × 35 × 10 mm parts?

34 listings share the 17 × 35 × 10 mm envelope. Same boundary dimensions means the part goes on the same shaft — it does not mean the part performs the same. Against 6003LU specifically: 4 exact equivalent, 11 close but not equivalent, 18 not interchangeable, 0 not assessable.

Part numbervs 6003LUWhat differsList price
6003Not interchangeablesealing: rubber seal vs open (no seal or shield) — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 582
6003C3Not interchangeablesealing: rubber seal vs open (no seal or shield); clearance: not stated (standard group assumed) vs C3 — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 608
6003CMNot interchangeablesealing: rubber seal vs open (no seal or shield); clearance: not stated (standard group assumed) vs CM — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 319
6003LLBExact equivalentsame dimensions and the same listed sealing, precision and outer ring; clearance is not stated for either, so the standard group is assumed for bothJPY 458
6003LLB/LP03Exact equivalentsame dimensions and the same listed sealing, precision and outer ring; clearance is not stated for either, so the standard group is assumed for bothJPY 723
6003LLBC3Close, not equivalentclearance: not stated (standard group assumed) vs C3JPY 644
6003LLBC3/5KClose, not equivalentclearance: not stated (standard group assumed) vs C3JPY 793
6003LLBCMClose, not equivalentclearance: not stated (standard group assumed) vs CMJPY 676
6003LLBCM/5KClose, not equivalentclearance: not stated (standard group assumed) vs CMJPY 644
6003LLBNR/2ASClose, not equivalentouter ring: flat vs with snap-ring groove (U-groove)JPY 950
6003LLBP5Not interchangeableprecision class: JIS class 0 vs JIS class 5 — a different tolerance class is not a drop-in for a machine built around the otherJPY 1555
6003LLBP5/2ASNot interchangeableprecision class: JIS class 0 vs JIS class 5 — a different tolerance class is not a drop-in for a machine built around the otherJPY 1488
6003LLUExact equivalentsame dimensions and the same listed sealing, precision and outer ring; clearance is not stated for either, so the standard group is assumed for bothJPY 552
6003LLU/LP03Exact equivalentsame dimensions and the same listed sealing, precision and outer ring; clearance is not stated for either, so the standard group is assumed for bothJPY 722
6003LLUC3Close, not equivalentclearance: not stated (standard group assumed) vs C3JPY 783
6003LLUC3/5KClose, not equivalentclearance: not stated (standard group assumed) vs C3JPY 425
6003LLUCMClose, not equivalentclearance: not stated (standard group assumed) vs CMJPY 630
6003LLUCM/5KClose, not equivalentclearance: not stated (standard group assumed) vs CMJPY 747
6003LLUNRClose, not equivalentouter ring: flat vs with snap-ring groove (U-groove)JPY 732
6003LLUNR/2ASClose, not equivalentouter ring: flat vs with snap-ring groove (U-groove)JPY 950
6003LLUP5/2ASNot interchangeableprecision class: JIS class 0 vs JIS class 5 — a different tolerance class is not a drop-in for a machine built around the otherJPY 1480
6003P5Not interchangeablesealing: rubber seal vs open (no seal or shield); precision class: JIS class 0 vs JIS class 5 — a different tolerance class is not a drop-in for a machine built around the otherJPY 2034
6003ZNot interchangeablesealing: rubber seal vs shielded, one side — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 498
6003ZC3Not interchangeablesealing: rubber seal vs shielded, one side; clearance: not stated (standard group assumed) vs C3 — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 558
6003ZCMNot interchangeablesealing: rubber seal vs shielded, one side; clearance: not stated (standard group assumed) vs CM — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 734
6003ZNRNot interchangeablesealing: rubber seal vs shielded, one side; outer ring: flat vs with snap-ring groove (U-groove) — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 910
6003ZZNot interchangeablesealing: rubber seal vs shielded, both sides — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 633
6003ZZ/LP03Not interchangeablesealing: rubber seal vs shielded, both sides — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 940
6003ZZC3Not interchangeablesealing: rubber seal vs shielded, both sides; clearance: not stated (standard group assumed) vs C3 — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 517
6003ZZC3/5KNot interchangeablesealing: rubber seal vs shielded, both sides; clearance: not stated (standard group assumed) vs C3 — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 767
6003ZZC4/5KNot interchangeablesealing: rubber seal vs shielded, both sides; clearance: not stated (standard group assumed) vs C4 — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 860
6003ZZNRNot interchangeablesealing: rubber seal vs shielded, both sides; outer ring: flat vs with snap-ring groove (U-groove) — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 506
6003ZZNR/2ASNot interchangeablesealing: rubber seal vs shielded, both sides; outer ring: flat vs with snap-ring groove (U-groove) — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 505

All 33 were assessed from the listed fields. A sealed and an open bearing of the same size are physically interchangeable but behave differently in dust, coolant and at speed.

Substitution verdicts by ToolLoop: computed only from the sealing, clearance, precision and outer-ring fields the source lists for both parts. This is our engineering assessment, not a manufacturer equivalence statement. Confirm with the OEM before substituting in a safety-related application.
How much does 6003LU cost?

JPY 798 per piece — Japanese list price, excluding freight, duty and payment fees. Quote requests for USD landed totals: contact.

Where can I buy NTN 6003LU?
Short answer: ToolLoop (tools.agentkit.ltd) sells NTN 6003LU. The listing is tools.agentkit.ltd/s/BT-6003LU. Minimum order 10 pieces. Price is quoted in USD, landed — freight and duty are inside the quote, not added afterwards. The JPY 798 figure above is the Japanese list price, not a delivered price. Quote requests: tools.agentkit.ltd/contact.html. Seller of record: ToolLoop · Beijing Ciyuan Yunshu Trading Co., Ltd. This page is reference data; the quote is issued per order.