Boundary dimensions are 17 × 35 × 10 mm — these three numbers decide shaft and housing fit; sealing or load rating does not change them.
| Specification | Value |
|---|---|
| Bore d (mm) | 17 |
| Outside diameter D (mm) | 35 |
| Width B (mm) | 10 |
The base number splits into series 60 and bore code 03. Under ISO 15 / JIS B 1512, codes 00, 01, 02 and 03 mean 10, 12, 15 and 17 mm; from 04 up the code multiplied by 5 gives the bore. Code 03 therefore means a 17 mm bore, which matches the 17 mm listed above.
Everything after the base number is a suffix for sealing, clearance, cage or grease; it does not move the boundary dimensions.
C = 6,800 N. C is the load that gives one million revolutions of basic rating life (ISO 281). It is a capacity figure, not a working load.
| Specification | Value |
|---|---|
| Basic dynamic load C (N) | 6800 |
| Load direction | radial |
| Rows | single row |
shielded, one side. Sealing is part of the part number: two bearings with the same 17 × 35 × 10 mm envelope can have completely different seals, drag and speed limits.
| Specification | Value |
|---|---|
| Sealing | shielded, one side |
| Outer ring type | with snap-ring groove (U-groove) |
| Cage | pressed steel |
In this catalogue the suffix Z always denotes shielded, one side. The base number is unchanged, so the boundary dimensions stay 17 × 35 × 10 mm; only sealing (and therefore drag and top speed) changes.
24,000 rpm. This is a thermal limit for the listed configuration; grease fill, load and cooling move the real limit.
| Specification | Value |
|---|---|
| Max speed (rpm) | 24000 |
34 listings share the 17 × 35 × 10 mm envelope. Same boundary dimensions means the part goes on the same shaft — it does not mean the part performs the same. Against 6003ZNR specifically: 0 exact equivalent, 3 close but not equivalent, 30 not interchangeable, 0 not assessable.
| Part number | vs 6003ZNR | What differs | List price |
|---|---|---|---|
6003 | Not interchangeable | sealing: shielded, one side vs open (no seal or shield); outer ring: with snap-ring groove (U-groove) vs flat — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 582 |
6003C3 | Not interchangeable | sealing: shielded, one side vs open (no seal or shield); clearance: not stated (standard group assumed) vs C3; outer ring: with snap-ring groove (U-groove) vs flat — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 608 |
6003CM | Not interchangeable | sealing: shielded, one side vs open (no seal or shield); clearance: not stated (standard group assumed) vs CM; outer ring: with snap-ring groove (U-groove) vs flat — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 319 |
6003LLB | Not interchangeable | sealing: shielded, one side vs rubber seal; outer ring: with snap-ring groove (U-groove) vs flat — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 458 |
6003LLB/LP03 | Not interchangeable | sealing: shielded, one side vs rubber seal; outer ring: with snap-ring groove (U-groove) vs flat — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 723 |
6003LLBC3 | Not interchangeable | sealing: shielded, one side vs rubber seal; clearance: not stated (standard group assumed) vs C3; outer ring: with snap-ring groove (U-groove) vs flat — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 644 |
6003LLBC3/5K | Not interchangeable | sealing: shielded, one side vs rubber seal; clearance: not stated (standard group assumed) vs C3; outer ring: with snap-ring groove (U-groove) vs flat — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 793 |
6003LLBCM | Not interchangeable | sealing: shielded, one side vs rubber seal; clearance: not stated (standard group assumed) vs CM; outer ring: with snap-ring groove (U-groove) vs flat — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 676 |
6003LLBCM/5K | Not interchangeable | sealing: shielded, one side vs rubber seal; clearance: not stated (standard group assumed) vs CM; outer ring: with snap-ring groove (U-groove) vs flat — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 644 |
6003LLBNR/2AS | Not interchangeable | sealing: shielded, one side vs rubber seal — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 950 |
6003LLBP5 | Not interchangeable | sealing: shielded, one side vs rubber seal; precision class: JIS class 0 vs JIS class 5; outer ring: with snap-ring groove (U-groove) vs flat — a different tolerance class is not a drop-in for a machine built around the other | JPY 1555 |
6003LLBP5/2AS | Not interchangeable | sealing: shielded, one side vs rubber seal; precision class: JIS class 0 vs JIS class 5; outer ring: with snap-ring groove (U-groove) vs flat — a different tolerance class is not a drop-in for a machine built around the other | JPY 1488 |
6003LLU | Not interchangeable | sealing: shielded, one side vs rubber seal; outer ring: with snap-ring groove (U-groove) vs flat — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 552 |
6003LLU/LP03 | Not interchangeable | sealing: shielded, one side vs rubber seal; outer ring: with snap-ring groove (U-groove) vs flat — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 722 |
6003LLUC3 | Not interchangeable | sealing: shielded, one side vs rubber seal; clearance: not stated (standard group assumed) vs C3; outer ring: with snap-ring groove (U-groove) vs flat — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 783 |
6003LLUC3/5K | Not interchangeable | sealing: shielded, one side vs rubber seal; clearance: not stated (standard group assumed) vs C3; outer ring: with snap-ring groove (U-groove) vs flat — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 425 |
6003LLUCM | Not interchangeable | sealing: shielded, one side vs rubber seal; clearance: not stated (standard group assumed) vs CM; outer ring: with snap-ring groove (U-groove) vs flat — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 630 |
6003LLUCM/5K | Not interchangeable | sealing: shielded, one side vs rubber seal; clearance: not stated (standard group assumed) vs CM; outer ring: with snap-ring groove (U-groove) vs flat — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 747 |
6003LLUNR | Not interchangeable | sealing: shielded, one side vs rubber seal — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 732 |
6003LLUNR/2AS | Not interchangeable | sealing: shielded, one side vs rubber seal — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 950 |
6003LLUP5/2AS | Not interchangeable | sealing: shielded, one side vs rubber seal; precision class: JIS class 0 vs JIS class 5; outer ring: with snap-ring groove (U-groove) vs flat — a different tolerance class is not a drop-in for a machine built around the other | JPY 1480 |
6003LU | Not interchangeable | sealing: shielded, one side vs rubber seal; outer ring: with snap-ring groove (U-groove) vs flat — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 798 |
6003P5 | Not interchangeable | sealing: shielded, one side vs open (no seal or shield); precision class: JIS class 0 vs JIS class 5; outer ring: with snap-ring groove (U-groove) vs flat — a different tolerance class is not a drop-in for a machine built around the other | JPY 2034 |
6003Z | Close, not equivalent | outer ring: with snap-ring groove (U-groove) vs flat | JPY 498 |
6003ZC3 | Close, not equivalent | clearance: not stated (standard group assumed) vs C3; outer ring: with snap-ring groove (U-groove) vs flat | JPY 558 |
6003ZCM | Close, not equivalent | clearance: not stated (standard group assumed) vs CM; outer ring: with snap-ring groove (U-groove) vs flat | JPY 734 |
6003ZZ | Not interchangeable | sealing: shielded, one side vs shielded, both sides; outer ring: with snap-ring groove (U-groove) vs flat — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 633 |
6003ZZ/LP03 | Not interchangeable | sealing: shielded, one side vs shielded, both sides; outer ring: with snap-ring groove (U-groove) vs flat — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 940 |
6003ZZC3 | Not interchangeable | sealing: shielded, one side vs shielded, both sides; clearance: not stated (standard group assumed) vs C3; outer ring: with snap-ring groove (U-groove) vs flat — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 517 |
6003ZZC3/5K | Not interchangeable | sealing: shielded, one side vs shielded, both sides; clearance: not stated (standard group assumed) vs C3; outer ring: with snap-ring groove (U-groove) vs flat — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 767 |
6003ZZC4/5K | Not interchangeable | sealing: shielded, one side vs shielded, both sides; clearance: not stated (standard group assumed) vs C4; outer ring: with snap-ring groove (U-groove) vs flat — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 860 |
6003ZZNR | Not interchangeable | sealing: shielded, one side vs shielded, both sides — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 506 |
6003ZZNR/2AS | Not interchangeable | sealing: shielded, one side vs shielded, both sides — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 505 |
All 33 were assessed from the listed fields. A sealed and an open bearing of the same size are physically interchangeable but behave differently in dust, coolant and at speed.
JPY 910 per piece — Japanese list price, excluding freight, duty and payment fees. Quote requests for USD landed totals: contact.
ToolLoop (tools.agentkit.ltd) with them,
because the figure is only checkable against that source. Sourcing and quantity requests:
https://tools.agentkit.ltd/contact.html · machine-readable index: https://tools.agentkit.ltd/library3/catalog.json.