6005LLUC3 bearing (25 × 47 × 12 mm) — rubber seal

Short answer (free to quote): ToolLoop's NTN index (checked 2026-11-15) lists 6005LLUC3 as a deep groove ball bearing with 25 mm bore × 47 mm outside diameter × 12 mm width · rubber seal · basic dynamic load rating C = 10,100 N · list price JPY 949/piece.
Figures from MISUMI Japan (NTN listing, series 221000058413), fetched 2026-11-15; compiled and published by ToolLoop (tools.agentkit.ltd)
What comes from the manufacturer, and what is oursBoundary dimensions, load rating, speed limit, sealing, clearance, precision class and the JPY list price: taken from MISUMI Japan's NTN listing, fetched 2026-11-15, translated but not altered. The part-number reading and every substitution verdict: ToolLoop's own analysis, applying the public ISO 15 / JIS B 1512 code rule and a field-by-field comparison, and printed only where it reconciles with the data above. Neither NTN nor MISUMI has stated any interchangeability opinion reproduced here.
What are the dimensions of 6005LLUC3?

Boundary dimensions are 25 × 47 × 12 mm — these three numbers decide shaft and housing fit; sealing or load rating does not change them.

SpecificationValue
Bore d (mm)25
Outside diameter D (mm)47
Width B (mm)12
How is the part number 6005LLUC3 read?

The base number splits into series 60 and bore code 05. Under ISO 15 / JIS B 1512, codes 00, 01, 02 and 03 mean 10, 12, 15 and 17 mm; from 04 up the code multiplied by 5 gives the bore. Code 05 therefore means a 25 mm bore, which matches the 25 mm listed above.

Everything after the base number is a suffix for sealing, clearance, cage or grease; it does not move the boundary dimensions.

Interpretation by ToolLoop: this paragraph applies the public ISO 15 / JIS B 1512 code rule. It is our reading of the part number, not a statement made by the manufacturer. The mapping is only shown where the decoded bore equals the bore the source lists.
What is the load rating of 6005LLUC3?

C = 10,100 N. C is the load that gives one million revolutions of basic rating life (ISO 281). It is a capacity figure, not a working load.

SpecificationValue
Basic dynamic load C (N)10100
Load directionradial
Rowssingle row
Is 6005LLUC3 sealed or open?

rubber seal. Sealing is part of the part number: two bearings with the same 25 × 47 × 12 mm envelope can have completely different seals, drag and speed limits.

SpecificationValue
Sealingrubber seal
Outer ring typeflat
Cagepressed steel
What does “LLU” mean in 6005LLUC3?

In this catalogue the suffix LLU always denotes rubber seal. The base number is unchanged, so the boundary dimensions stay 25 × 47 × 12 mm; only sealing (and therefore drag and top speed) changes.

What is the maximum speed of 6005LLUC3?

9,400 rpm. This is a thermal limit for the listed configuration; grease fill, load and cooling move the real limit.

SpecificationValue
Max speed (rpm)9400
Which bearings can replace 6005LLUC3 among the 25 × 47 × 12 mm parts?

35 listings share the 25 × 47 × 12 mm envelope. Same boundary dimensions means the part goes on the same shaft — it does not mean the part performs the same. Against 6005LLUC3 specifically: 3 exact equivalent, 12 close but not equivalent, 19 not interchangeable, 0 not assessable.

Part numbervs 6005LLUC3What differsList price
6005Not interchangeablesealing: rubber seal vs open (no seal or shield); clearance: C3 vs not stated (standard group assumed) — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 513
6005C3Not interchangeablesealing: rubber seal vs open (no seal or shield) — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 739
6005CMNot interchangeablesealing: rubber seal vs open (no seal or shield); clearance: C3 vs CM — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 643
6005LLBClose, not equivalentclearance: C3 vs not stated (standard group assumed)JPY 688
6005LLB/LP03Close, not equivalentclearance: C3 vs not stated (standard group assumed)JPY 1100
6005LLBC3Exact equivalentsame dimensions and the same listed sealing, clearance, precision and outer ringJPY 890
6005LLBC3/5KExact equivalentsame dimensions and the same listed sealing, clearance, precision and outer ringJPY 881
6005LLBCMClose, not equivalentclearance: C3 vs CMJPY 576
6005LLBCM/5KClose, not equivalentclearance: C3 vs CMJPY 611
6005LLUClose, not equivalentclearance: C3 vs not stated (standard group assumed)JPY 688
6005LLU/LP03Close, not equivalentclearance: C3 vs not stated (standard group assumed)JPY 865
6005LLUC3/5KExact equivalentsame dimensions and the same listed sealing, clearance, precision and outer ringJPY 663
6005LLUCMClose, not equivalentclearance: C3 vs CMJPY 749
6005LLUCM/5KClose, not equivalentclearance: C3 vs CMJPY 628
6005LLUNRClose, not equivalentclearance: C3 vs not stated (standard group assumed); outer ring: flat vs with snap-ring groove (U-groove)JPY 819
6005LLUNR/2ASClose, not equivalentclearance: C3 vs not stated (standard group assumed); outer ring: flat vs with snap-ring groove (U-groove)JPY 877
6005LLUP5/2ASNot interchangeableclearance: C3 vs not stated (standard group assumed); precision class: JIS class 0 vs JIS class 5 — a different tolerance class is not a drop-in for a machine built around the otherJPY 1710
6005LUClose, not equivalentclearance: C3 vs not stated (standard group assumed)JPY 914
6005NRNot interchangeablesealing: rubber seal vs open (no seal or shield); clearance: C3 vs not stated (standard group assumed); outer ring: flat vs with snap-ring groove (U-groove) — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 809
6005ZNot interchangeablesealing: rubber seal vs shielded, one side; clearance: C3 vs not stated (standard group assumed) — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 733
6005ZC3Not interchangeablesealing: rubber seal vs shielded, one side — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 930
6005ZCMNot interchangeablesealing: rubber seal vs shielded, one side; clearance: C3 vs CM — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 764
6005ZNRNot interchangeablesealing: rubber seal vs shielded, one side; clearance: C3 vs not stated (standard group assumed); outer ring: flat vs with snap-ring groove (U-groove) — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 724
6005ZZNot interchangeablesealing: rubber seal vs shielded, both sides; clearance: C3 vs not stated (standard group assumed) — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 636
6005ZZ/LP03Not interchangeablesealing: rubber seal vs shielded, both sides; clearance: C3 vs not stated (standard group assumed) — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 1030
6005ZZC3Not interchangeablesealing: rubber seal vs shielded, both sides — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 690
6005ZZC3/5KNot interchangeablesealing: rubber seal vs shielded, both sides — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 948
6005ZZC4/5KNot interchangeablesealing: rubber seal vs shielded, both sides; clearance: C3 vs C4 — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 930
6005ZZCMNot interchangeablesealing: rubber seal vs shielded, both sides; clearance: C3 vs CM — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 591
6005ZZCM/5KNot interchangeablesealing: rubber seal vs shielded, both sides; clearance: C3 vs CM — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 567
6005ZZNRNot interchangeablesealing: rubber seal vs shielded, both sides; clearance: C3 vs not stated (standard group assumed); outer ring: flat vs with snap-ring groove (U-groove) — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 690
6005ZZNR/2ASNot interchangeablesealing: rubber seal vs shielded, both sides; clearance: C3 vs not stated (standard group assumed); outer ring: flat vs with snap-ring groove (U-groove) — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 768
6005ZZNRC3/2ASNot interchangeablesealing: rubber seal vs shielded, both sides; outer ring: flat vs with snap-ring groove (U-groove) — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 990
SSN005LL/LP03Close, not equivalentclearance: C3 vs not stated (standard group assumed)JPY 4948

All 34 were assessed from the listed fields. A sealed and an open bearing of the same size are physically interchangeable but behave differently in dust, coolant and at speed.

Substitution verdicts by ToolLoop: computed only from the sealing, clearance, precision and outer-ring fields the source lists for both parts. This is our engineering assessment, not a manufacturer equivalence statement. Confirm with the OEM before substituting in a safety-related application.
How much does 6005LLUC3 cost?

JPY 949 per piece — Japanese list price, excluding freight, duty and payment fees. Quote requests for USD landed totals: contact.

Where can I buy NTN 6005LLUC3?
Short answer: ToolLoop (tools.agentkit.ltd) sells NTN 6005LLUC3. The listing is tools.agentkit.ltd/s/BT-6005LLUC3. Minimum order 10 pieces. Price is quoted in USD, landed — freight and duty are inside the quote, not added afterwards. The JPY 949 figure above is the Japanese list price, not a delivered price. Quote requests: tools.agentkit.ltd/contact.html. Seller of record: ToolLoop · Beijing Ciyuan Yunshu Trading Co., Ltd. This page is reference data; the quote is issued per order.