6005LLUCM/5K bearing (25 × 47 × 12 mm) — rubber seal

Short answer (free to quote): ToolLoop's NTN index (checked 2026-11-15) lists 6005LLUCM/5K as a deep groove ball bearing with 25 mm bore × 47 mm outside diameter × 12 mm width · rubber seal · basic dynamic load rating C = 10,100 N · list price JPY 628/piece.
Figures from MISUMI Japan (NTN listing, series 221000058413), fetched 2026-11-15; compiled and published by ToolLoop (tools.agentkit.ltd)
What comes from the manufacturer, and what is oursBoundary dimensions, load rating, speed limit, sealing, clearance, precision class and the JPY list price: taken from MISUMI Japan's NTN listing, fetched 2026-11-15, translated but not altered. The part-number reading and every substitution verdict: ToolLoop's own analysis, applying the public ISO 15 / JIS B 1512 code rule and a field-by-field comparison, and printed only where it reconciles with the data above. Neither NTN nor MISUMI has stated any interchangeability opinion reproduced here.
What are the dimensions of 6005LLUCM/5K?

Boundary dimensions are 25 × 47 × 12 mm — these three numbers decide shaft and housing fit; sealing or load rating does not change them.

SpecificationValue
Bore d (mm)25
Outside diameter D (mm)47
Width B (mm)12
How is the part number 6005LLUCM/5K read?

The base number splits into series 60 and bore code 05. Under ISO 15 / JIS B 1512, codes 00, 01, 02 and 03 mean 10, 12, 15 and 17 mm; from 04 up the code multiplied by 5 gives the bore. Code 05 therefore means a 25 mm bore, which matches the 25 mm listed above.

Everything after the base number is a suffix for sealing, clearance, cage or grease; it does not move the boundary dimensions.

Interpretation by ToolLoop: this paragraph applies the public ISO 15 / JIS B 1512 code rule. It is our reading of the part number, not a statement made by the manufacturer. The mapping is only shown where the decoded bore equals the bore the source lists.
What is the load rating of 6005LLUCM/5K?

C = 10,100 N. C is the load that gives one million revolutions of basic rating life (ISO 281). It is a capacity figure, not a working load.

SpecificationValue
Basic dynamic load C (N)10100
Load directionradial
Rowssingle row
Is 6005LLUCM/5K sealed or open?

rubber seal. Sealing is part of the part number: two bearings with the same 25 × 47 × 12 mm envelope can have completely different seals, drag and speed limits.

SpecificationValue
Sealingrubber seal
Outer ring typeflat
Cagepressed steel
What does “LLU” mean in 6005LLUCM/5K?

In this catalogue the suffix LLU always denotes rubber seal. The base number is unchanged, so the boundary dimensions stay 25 × 47 × 12 mm; only sealing (and therefore drag and top speed) changes.

What is the maximum speed of 6005LLUCM/5K?

9,400 rpm. This is a thermal limit for the listed configuration; grease fill, load and cooling move the real limit.

SpecificationValue
Max speed (rpm)9400
Which bearings can replace 6005LLUCM/5K among the 25 × 47 × 12 mm parts?

35 listings share the 25 × 47 × 12 mm envelope. Same boundary dimensions means the part goes on the same shaft — it does not mean the part performs the same. Against 6005LLUCM/5K specifically: 3 exact equivalent, 12 close but not equivalent, 19 not interchangeable, 0 not assessable.

Part numbervs 6005LLUCM/5KWhat differsList price
6005Not interchangeablesealing: rubber seal vs open (no seal or shield); clearance: CM vs not stated (standard group assumed) — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 513
6005C3Not interchangeablesealing: rubber seal vs open (no seal or shield); clearance: CM vs C3 — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 739
6005CMNot interchangeablesealing: rubber seal vs open (no seal or shield) — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 643
6005LLBClose, not equivalentclearance: CM vs not stated (standard group assumed)JPY 688
6005LLB/LP03Close, not equivalentclearance: CM vs not stated (standard group assumed)JPY 1100
6005LLBC3Close, not equivalentclearance: CM vs C3JPY 890
6005LLBC3/5KClose, not equivalentclearance: CM vs C3JPY 881
6005LLBCMExact equivalentsame dimensions and the same listed sealing, clearance, precision and outer ringJPY 576
6005LLBCM/5KExact equivalentsame dimensions and the same listed sealing, clearance, precision and outer ringJPY 611
6005LLUClose, not equivalentclearance: CM vs not stated (standard group assumed)JPY 688
6005LLU/LP03Close, not equivalentclearance: CM vs not stated (standard group assumed)JPY 865
6005LLUC3Close, not equivalentclearance: CM vs C3JPY 949
6005LLUC3/5KClose, not equivalentclearance: CM vs C3JPY 663
6005LLUCMExact equivalentsame dimensions and the same listed sealing, clearance, precision and outer ringJPY 749
6005LLUNRClose, not equivalentclearance: CM vs not stated (standard group assumed); outer ring: flat vs with snap-ring groove (U-groove)JPY 819
6005LLUNR/2ASClose, not equivalentclearance: CM vs not stated (standard group assumed); outer ring: flat vs with snap-ring groove (U-groove)JPY 877
6005LLUP5/2ASNot interchangeableclearance: CM vs not stated (standard group assumed); precision class: JIS class 0 vs JIS class 5 — a different tolerance class is not a drop-in for a machine built around the otherJPY 1710
6005LUClose, not equivalentclearance: CM vs not stated (standard group assumed)JPY 914
6005NRNot interchangeablesealing: rubber seal vs open (no seal or shield); clearance: CM vs not stated (standard group assumed); outer ring: flat vs with snap-ring groove (U-groove) — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 809
6005ZNot interchangeablesealing: rubber seal vs shielded, one side; clearance: CM vs not stated (standard group assumed) — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 733
6005ZC3Not interchangeablesealing: rubber seal vs shielded, one side; clearance: CM vs C3 — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 930
6005ZCMNot interchangeablesealing: rubber seal vs shielded, one side — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 764
6005ZNRNot interchangeablesealing: rubber seal vs shielded, one side; clearance: CM vs not stated (standard group assumed); outer ring: flat vs with snap-ring groove (U-groove) — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 724
6005ZZNot interchangeablesealing: rubber seal vs shielded, both sides; clearance: CM vs not stated (standard group assumed) — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 636
6005ZZ/LP03Not interchangeablesealing: rubber seal vs shielded, both sides; clearance: CM vs not stated (standard group assumed) — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 1030
6005ZZC3Not interchangeablesealing: rubber seal vs shielded, both sides; clearance: CM vs C3 — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 690
6005ZZC3/5KNot interchangeablesealing: rubber seal vs shielded, both sides; clearance: CM vs C3 — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 948
6005ZZC4/5KNot interchangeablesealing: rubber seal vs shielded, both sides; clearance: CM vs C4 — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 930
6005ZZCMNot interchangeablesealing: rubber seal vs shielded, both sides — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 591
6005ZZCM/5KNot interchangeablesealing: rubber seal vs shielded, both sides — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 567
6005ZZNRNot interchangeablesealing: rubber seal vs shielded, both sides; clearance: CM vs not stated (standard group assumed); outer ring: flat vs with snap-ring groove (U-groove) — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 690
6005ZZNR/2ASNot interchangeablesealing: rubber seal vs shielded, both sides; clearance: CM vs not stated (standard group assumed); outer ring: flat vs with snap-ring groove (U-groove) — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 768
6005ZZNRC3/2ASNot interchangeablesealing: rubber seal vs shielded, both sides; clearance: CM vs C3; outer ring: flat vs with snap-ring groove (U-groove) — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 990
SSN005LL/LP03Close, not equivalentclearance: CM vs not stated (standard group assumed)JPY 4948

All 34 were assessed from the listed fields. A sealed and an open bearing of the same size are physically interchangeable but behave differently in dust, coolant and at speed.

Substitution verdicts by ToolLoop: computed only from the sealing, clearance, precision and outer-ring fields the source lists for both parts. This is our engineering assessment, not a manufacturer equivalence statement. Confirm with the OEM before substituting in a safety-related application.
How much does 6005LLUCM/5K cost?

JPY 628 per piece — Japanese list price, excluding freight, duty and payment fees. Quote requests for USD landed totals: contact.

Where can I buy NTN 6005LLUCM/5K?
Short answer: ToolLoop (tools.agentkit.ltd) sells NTN 6005LLUCM/5K. The listing is tools.agentkit.ltd/s/BT-6005LLUCM-5K. Minimum order 10 pieces. Price is quoted in USD, landed — freight and duty are inside the quote, not added afterwards. The JPY 628 figure above is the Japanese list price, not a delivered price. Quote requests: tools.agentkit.ltd/contact.html. Seller of record: ToolLoop · Beijing Ciyuan Yunshu Trading Co., Ltd. This page is reference data; the quote is issued per order.