Boundary dimensions are 35 × 62 × 14 mm — these three numbers decide shaft and housing fit; sealing or load rating does not change them.
| Specification | Value |
|---|---|
| Bore d (mm) | 35 |
| Outside diameter D (mm) | 62 |
| Width B (mm) | 14 |
The base number splits into series 60 and bore code 07. Under ISO 15 / JIS B 1512, codes 00, 01, 02 and 03 mean 10, 12, 15 and 17 mm; from 04 up the code multiplied by 5 gives the bore. Code 07 therefore means a 35 mm bore, which matches the 35 mm listed above.
Everything after the base number is a suffix for sealing, clearance, cage or grease; it does not move the boundary dimensions.
C = 16,000 N. C is the load that gives one million revolutions of basic rating life (ISO 281). It is a capacity figure, not a working load.
| Specification | Value |
|---|---|
| Basic dynamic load C (N) | 16000 |
| Load direction | radial |
| Rows | single row |
rubber seal. Sealing is part of the part number: two bearings with the same 35 × 62 × 14 mm envelope can have completely different seals, drag and speed limits.
| Specification | Value |
|---|---|
| Sealing | rubber seal |
| Outer ring type | flat |
| Cage | pressed steel |
In this catalogue the suffix LLB always denotes rubber seal. The base number is unchanged, so the boundary dimensions stay 35 × 62 × 14 mm; only sealing (and therefore drag and top speed) changes.
12,000 rpm. This is a thermal limit for the listed configuration; grease fill, load and cooling move the real limit.
| Specification | Value |
|---|---|
| Max speed (rpm) | 12000 |
35 listings share the 35 × 62 × 14 mm envelope. Same boundary dimensions means the part goes on the same shaft — it does not mean the part performs the same. Against 6007LLBC3/5K specifically: 2 exact equivalent, 12 close but not equivalent, 20 not interchangeable, 0 not assessable.
| Part number | vs 6007LLBC3/5K | What differs | List price |
|---|---|---|---|
6007C3 | Not interchangeable | sealing: rubber seal vs open (no seal or shield) — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 1048 |
6007CM | Not interchangeable | sealing: rubber seal vs open (no seal or shield); clearance: C3 vs CM — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 844 |
6007LB | Close, not equivalent | clearance: C3 vs not stated (standard group assumed) | JPY 1081 |
6007LLB | Close, not equivalent | clearance: C3 vs not stated (standard group assumed) | JPY 1018 |
6007LLBC3 | Exact equivalent | same dimensions and the same listed sealing, clearance, precision and outer ring | JPY 1123 |
6007LLBCM | Close, not equivalent | clearance: C3 vs CM | JPY 896 |
6007LLBCM/5K | Close, not equivalent | clearance: C3 vs CM | JPY 942 |
6007LLBNR | Close, not equivalent | clearance: C3 vs not stated (standard group assumed); outer ring: flat vs with snap-ring groove (U-groove) | JPY 1034 |
6007LLBNR/2AS | Close, not equivalent | clearance: C3 vs not stated (standard group assumed); outer ring: flat vs with snap-ring groove (U-groove) | JPY 1023 |
6007LLBP5/2AS | Not interchangeable | clearance: C3 vs not stated (standard group assumed); precision class: JIS class 0 vs JIS class 5 — a different tolerance class is not a drop-in for a machine built around the other | JPY 2240 |
6007LLU | Close, not equivalent | clearance: C3 vs not stated (standard group assumed) | JPY 1018 |
6007LLU/LP03 | Close, not equivalent | clearance: C3 vs not stated (standard group assumed) | JPY 1350 |
6007LLUC3/5K | Exact equivalent | same dimensions and the same listed sealing, clearance, precision and outer ring | JPY 1212 |
6007LLUCM | Close, not equivalent | clearance: C3 vs CM | JPY 1011 |
6007LLUCM/5K | Close, not equivalent | clearance: C3 vs CM | JPY 962 |
6007LLUNR/2AS | Close, not equivalent | clearance: C3 vs not stated (standard group assumed); outer ring: flat vs with snap-ring groove (U-groove) | JPY 1260 |
6007LU | Close, not equivalent | clearance: C3 vs not stated (standard group assumed) | JPY 914 |
6007NR | Not interchangeable | sealing: rubber seal vs open (no seal or shield); clearance: C3 vs not stated (standard group assumed); outer ring: flat vs with snap-ring groove (U-groove) — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 860 |
6007P4 | Not interchangeable | sealing: rubber seal vs open (no seal or shield); clearance: C3 vs not stated (standard group assumed); precision class: JIS class 0 vs JIS class 4 — a different tolerance class is not a drop-in for a machine built around the other | JPY 4341 |
6007P5 | Not interchangeable | sealing: rubber seal vs open (no seal or shield); clearance: C3 vs not stated (standard group assumed); precision class: JIS class 0 vs JIS class 5 — a different tolerance class is not a drop-in for a machine built around the other | JPY 3619 |
6007U1 | Not interchangeable | sealing: rubber seal vs open (no seal or shield); clearance: C3 vs not stated (standard group assumed) — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 1030 |
6007Z | Not interchangeable | sealing: rubber seal vs shielded, one side; clearance: C3 vs not stated (standard group assumed) — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 902 |
6007ZC3 | Not interchangeable | sealing: rubber seal vs shielded, one side — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 869 |
6007ZCM | Not interchangeable | sealing: rubber seal vs shielded, one side; clearance: C3 vs CM — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 707 |
6007ZZ | Not interchangeable | sealing: rubber seal vs shielded, both sides; clearance: C3 vs not stated (standard group assumed) — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 901 |
6007ZZ/LP03 | Not interchangeable | sealing: rubber seal vs shielded, both sides; clearance: C3 vs not stated (standard group assumed) — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 1260 |
6007ZZC3 | Not interchangeable | sealing: rubber seal vs shielded, both sides — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 831 |
6007ZZC3/5K | Not interchangeable | sealing: rubber seal vs shielded, both sides — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 935 |
6007ZZC4/5K | Not interchangeable | sealing: rubber seal vs shielded, both sides; clearance: C3 vs C4 — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 1100 |
6007ZZCM | Not interchangeable | sealing: rubber seal vs shielded, both sides; clearance: C3 vs CM — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 796 |
6007ZZCM/5K | Not interchangeable | sealing: rubber seal vs shielded, both sides; clearance: C3 vs CM — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 898 |
6007ZZNR | Not interchangeable | sealing: rubber seal vs shielded, both sides; clearance: C3 vs not stated (standard group assumed); outer ring: flat vs with snap-ring groove (U-groove) — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 1094 |
6007ZZNR/2AS | Not interchangeable | sealing: rubber seal vs shielded, both sides; clearance: C3 vs not stated (standard group assumed); outer ring: flat vs with snap-ring groove (U-groove) — sealing sets what the bearing survives, so this is a change of duty, not just a fit | JPY 1032 |
6007ZZP5/2AS | Not interchangeable | sealing: rubber seal vs shielded, both sides; clearance: C3 vs not stated (standard group assumed); precision class: JIS class 0 vs JIS class 5 — a different tolerance class is not a drop-in for a machine built around the other | JPY 2160 |
All 34 were assessed from the listed fields. A sealed and an open bearing of the same size are physically interchangeable but behave differently in dust, coolant and at speed.
JPY 1,246 per piece — Japanese list price, excluding freight, duty and payment fees. Quote requests for USD landed totals: contact.
ToolLoop (tools.agentkit.ltd) with them,
because the figure is only checkable against that source. Sourcing and quantity requests:
https://tools.agentkit.ltd/contact.html · machine-readable index: https://tools.agentkit.ltd/library3/catalog.json.