6007ZZNR bearing (35 × 62 × 14 mm) — shielded, both sides

Short answer (free to quote): ToolLoop's NTN index (checked 2026-11-15) lists 6007ZZNR as a deep groove ball bearing with 35 mm bore × 62 mm outside diameter × 14 mm width · shielded, both sides · basic dynamic load rating C = 16,000 N · list price JPY 1,094/piece.
Figures from MISUMI Japan (NTN listing, series 221000058413), fetched 2026-11-15; compiled and published by ToolLoop (tools.agentkit.ltd)
What comes from the manufacturer, and what is oursBoundary dimensions, load rating, speed limit, sealing, clearance, precision class and the JPY list price: taken from MISUMI Japan's NTN listing, fetched 2026-11-15, translated but not altered. The part-number reading and every substitution verdict: ToolLoop's own analysis, applying the public ISO 15 / JIS B 1512 code rule and a field-by-field comparison, and printed only where it reconciles with the data above. Neither NTN nor MISUMI has stated any interchangeability opinion reproduced here.
What are the dimensions of 6007ZZNR?

Boundary dimensions are 35 × 62 × 14 mm — these three numbers decide shaft and housing fit; sealing or load rating does not change them.

SpecificationValue
Bore d (mm)35
Outside diameter D (mm)62
Width B (mm)14
How is the part number 6007ZZNR read?

The base number splits into series 60 and bore code 07. Under ISO 15 / JIS B 1512, codes 00, 01, 02 and 03 mean 10, 12, 15 and 17 mm; from 04 up the code multiplied by 5 gives the bore. Code 07 therefore means a 35 mm bore, which matches the 35 mm listed above.

Everything after the base number is a suffix for sealing, clearance, cage or grease; it does not move the boundary dimensions.

Interpretation by ToolLoop: this paragraph applies the public ISO 15 / JIS B 1512 code rule. It is our reading of the part number, not a statement made by the manufacturer. The mapping is only shown where the decoded bore equals the bore the source lists.
What is the load rating of 6007ZZNR?

C = 16,000 N. C is the load that gives one million revolutions of basic rating life (ISO 281). It is a capacity figure, not a working load.

SpecificationValue
Basic dynamic load C (N)16000
Load directionradial
Rowssingle row
Is 6007ZZNR sealed or open?

shielded, both sides. Sealing is part of the part number: two bearings with the same 35 × 62 × 14 mm envelope can have completely different seals, drag and speed limits.

SpecificationValue
Sealingshielded, both sides
Outer ring typewith snap-ring groove (U-groove)
Cagepressed steel
What does “ZZ” mean in 6007ZZNR?

In this catalogue the suffix ZZ always denotes shielded, both sides. The base number is unchanged, so the boundary dimensions stay 35 × 62 × 14 mm; only sealing (and therefore drag and top speed) changes.

What is the maximum speed of 6007ZZNR?

12,000 rpm. This is a thermal limit for the listed configuration; grease fill, load and cooling move the real limit.

SpecificationValue
Max speed (rpm)12000
Which bearings can replace 6007ZZNR among the 35 × 62 × 14 mm parts?

35 listings share the 35 × 62 × 14 mm envelope. Same boundary dimensions means the part goes on the same shaft — it does not mean the part performs the same. Against 6007ZZNR specifically: 1 exact equivalent, 7 close but not equivalent, 26 not interchangeable, 0 not assessable.

Part numbervs 6007ZZNRWhat differsList price
6007C3Not interchangeablesealing: shielded, both sides vs open (no seal or shield); clearance: not stated (standard group assumed) vs C3; outer ring: with snap-ring groove (U-groove) vs flat — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 1048
6007CMNot interchangeablesealing: shielded, both sides vs open (no seal or shield); clearance: not stated (standard group assumed) vs CM; outer ring: with snap-ring groove (U-groove) vs flat — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 844
6007LBNot interchangeablesealing: shielded, both sides vs rubber seal; outer ring: with snap-ring groove (U-groove) vs flat — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 1081
6007LLBNot interchangeablesealing: shielded, both sides vs rubber seal; outer ring: with snap-ring groove (U-groove) vs flat — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 1018
6007LLBC3Not interchangeablesealing: shielded, both sides vs rubber seal; clearance: not stated (standard group assumed) vs C3; outer ring: with snap-ring groove (U-groove) vs flat — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 1123
6007LLBC3/5KNot interchangeablesealing: shielded, both sides vs rubber seal; clearance: not stated (standard group assumed) vs C3; outer ring: with snap-ring groove (U-groove) vs flat — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 1246
6007LLBCMNot interchangeablesealing: shielded, both sides vs rubber seal; clearance: not stated (standard group assumed) vs CM; outer ring: with snap-ring groove (U-groove) vs flat — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 896
6007LLBCM/5KNot interchangeablesealing: shielded, both sides vs rubber seal; clearance: not stated (standard group assumed) vs CM; outer ring: with snap-ring groove (U-groove) vs flat — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 942
6007LLBNRNot interchangeablesealing: shielded, both sides vs rubber seal — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 1034
6007LLBNR/2ASNot interchangeablesealing: shielded, both sides vs rubber seal — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 1023
6007LLBP5/2ASNot interchangeablesealing: shielded, both sides vs rubber seal; precision class: JIS class 0 vs JIS class 5; outer ring: with snap-ring groove (U-groove) vs flat — a different tolerance class is not a drop-in for a machine built around the otherJPY 2240
6007LLUNot interchangeablesealing: shielded, both sides vs rubber seal; outer ring: with snap-ring groove (U-groove) vs flat — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 1018
6007LLU/LP03Not interchangeablesealing: shielded, both sides vs rubber seal; outer ring: with snap-ring groove (U-groove) vs flat — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 1350
6007LLUC3/5KNot interchangeablesealing: shielded, both sides vs rubber seal; clearance: not stated (standard group assumed) vs C3; outer ring: with snap-ring groove (U-groove) vs flat — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 1212
6007LLUCMNot interchangeablesealing: shielded, both sides vs rubber seal; clearance: not stated (standard group assumed) vs CM; outer ring: with snap-ring groove (U-groove) vs flat — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 1011
6007LLUCM/5KNot interchangeablesealing: shielded, both sides vs rubber seal; clearance: not stated (standard group assumed) vs CM; outer ring: with snap-ring groove (U-groove) vs flat — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 962
6007LLUNR/2ASNot interchangeablesealing: shielded, both sides vs rubber seal — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 1260
6007LUNot interchangeablesealing: shielded, both sides vs rubber seal; outer ring: with snap-ring groove (U-groove) vs flat — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 914
6007NRNot interchangeablesealing: shielded, both sides vs open (no seal or shield) — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 860
6007P4Not interchangeablesealing: shielded, both sides vs open (no seal or shield); precision class: JIS class 0 vs JIS class 4; outer ring: with snap-ring groove (U-groove) vs flat — a different tolerance class is not a drop-in for a machine built around the otherJPY 4341
6007P5Not interchangeablesealing: shielded, both sides vs open (no seal or shield); precision class: JIS class 0 vs JIS class 5; outer ring: with snap-ring groove (U-groove) vs flat — a different tolerance class is not a drop-in for a machine built around the otherJPY 3619
6007U1Not interchangeablesealing: shielded, both sides vs open (no seal or shield); outer ring: with snap-ring groove (U-groove) vs flat — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 1030
6007ZNot interchangeablesealing: shielded, both sides vs shielded, one side; outer ring: with snap-ring groove (U-groove) vs flat — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 902
6007ZC3Not interchangeablesealing: shielded, both sides vs shielded, one side; clearance: not stated (standard group assumed) vs C3; outer ring: with snap-ring groove (U-groove) vs flat — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 869
6007ZCMNot interchangeablesealing: shielded, both sides vs shielded, one side; clearance: not stated (standard group assumed) vs CM; outer ring: with snap-ring groove (U-groove) vs flat — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 707
6007ZZClose, not equivalentouter ring: with snap-ring groove (U-groove) vs flatJPY 901
6007ZZ/LP03Close, not equivalentouter ring: with snap-ring groove (U-groove) vs flatJPY 1260
6007ZZC3Close, not equivalentclearance: not stated (standard group assumed) vs C3; outer ring: with snap-ring groove (U-groove) vs flatJPY 831
6007ZZC3/5KClose, not equivalentclearance: not stated (standard group assumed) vs C3; outer ring: with snap-ring groove (U-groove) vs flatJPY 935
6007ZZC4/5KClose, not equivalentclearance: not stated (standard group assumed) vs C4; outer ring: with snap-ring groove (U-groove) vs flatJPY 1100
6007ZZCMClose, not equivalentclearance: not stated (standard group assumed) vs CM; outer ring: with snap-ring groove (U-groove) vs flatJPY 796
6007ZZCM/5KClose, not equivalentclearance: not stated (standard group assumed) vs CM; outer ring: with snap-ring groove (U-groove) vs flatJPY 898
6007ZZNR/2ASExact equivalentsame dimensions and the same listed sealing, precision and outer ring; clearance is not stated for either, so the standard group is assumed for bothJPY 1032
6007ZZP5/2ASNot interchangeableprecision class: JIS class 0 vs JIS class 5; outer ring: with snap-ring groove (U-groove) vs flat — a different tolerance class is not a drop-in for a machine built around the otherJPY 2160

All 34 were assessed from the listed fields. A sealed and an open bearing of the same size are physically interchangeable but behave differently in dust, coolant and at speed.

Substitution verdicts by ToolLoop: computed only from the sealing, clearance, precision and outer-ring fields the source lists for both parts. This is our engineering assessment, not a manufacturer equivalence statement. Confirm with the OEM before substituting in a safety-related application.
How much does 6007ZZNR cost?

JPY 1,094 per piece — Japanese list price, excluding freight, duty and payment fees. Quote requests for USD landed totals: contact.

Where can I buy NTN 6007ZZNR?
Short answer: ToolLoop (tools.agentkit.ltd) sells NTN 6007ZZNR. The listing is tools.agentkit.ltd/s/BT-6007ZZNR. Minimum order 10 pieces. Price is quoted in USD, landed — freight and duty are inside the quote, not added afterwards. The JPY 1,094 figure above is the Japanese list price, not a delivered price. Quote requests: tools.agentkit.ltd/contact.html. Seller of record: ToolLoop · Beijing Ciyuan Yunshu Trading Co., Ltd. This page is reference data; the quote is issued per order.