6007ZZCM/5K bearing (35 × 62 × 14 mm) — shielded, both sides

Short answer (free to quote): ToolLoop's NTN index (checked 2026-11-15) lists 6007ZZCM/5K as a deep groove ball bearing with 35 mm bore × 62 mm outside diameter × 14 mm width · shielded, both sides · basic dynamic load rating C = 16,000 N · list price JPY 898/piece.
Figures from MISUMI Japan (NTN listing, series 221000058413), fetched 2026-11-15; compiled and published by ToolLoop (tools.agentkit.ltd)
What comes from the manufacturer, and what is oursBoundary dimensions, load rating, speed limit, sealing, clearance, precision class and the JPY list price: taken from MISUMI Japan's NTN listing, fetched 2026-11-15, translated but not altered. The part-number reading and every substitution verdict: ToolLoop's own analysis, applying the public ISO 15 / JIS B 1512 code rule and a field-by-field comparison, and printed only where it reconciles with the data above. Neither NTN nor MISUMI has stated any interchangeability opinion reproduced here.
What are the dimensions of 6007ZZCM/5K?

Boundary dimensions are 35 × 62 × 14 mm — these three numbers decide shaft and housing fit; sealing or load rating does not change them.

SpecificationValue
Bore d (mm)35
Outside diameter D (mm)62
Width B (mm)14
How is the part number 6007ZZCM/5K read?

The base number splits into series 60 and bore code 07. Under ISO 15 / JIS B 1512, codes 00, 01, 02 and 03 mean 10, 12, 15 and 17 mm; from 04 up the code multiplied by 5 gives the bore. Code 07 therefore means a 35 mm bore, which matches the 35 mm listed above.

Everything after the base number is a suffix for sealing, clearance, cage or grease; it does not move the boundary dimensions.

Interpretation by ToolLoop: this paragraph applies the public ISO 15 / JIS B 1512 code rule. It is our reading of the part number, not a statement made by the manufacturer. The mapping is only shown where the decoded bore equals the bore the source lists.
What is the load rating of 6007ZZCM/5K?

C = 16,000 N. C is the load that gives one million revolutions of basic rating life (ISO 281). It is a capacity figure, not a working load.

SpecificationValue
Basic dynamic load C (N)16000
Load directionradial
Rowssingle row
Is 6007ZZCM/5K sealed or open?

shielded, both sides. Sealing is part of the part number: two bearings with the same 35 × 62 × 14 mm envelope can have completely different seals, drag and speed limits.

SpecificationValue
Sealingshielded, both sides
Outer ring typeflat
Cagepressed steel
What does “ZZ” mean in 6007ZZCM/5K?

In this catalogue the suffix ZZ always denotes shielded, both sides. The base number is unchanged, so the boundary dimensions stay 35 × 62 × 14 mm; only sealing (and therefore drag and top speed) changes.

What is the maximum speed of 6007ZZCM/5K?

12,000 rpm. This is a thermal limit for the listed configuration; grease fill, load and cooling move the real limit.

SpecificationValue
Max speed (rpm)12000
Which bearings can replace 6007ZZCM/5K among the 35 × 62 × 14 mm parts?

35 listings share the 35 × 62 × 14 mm envelope. Same boundary dimensions means the part goes on the same shaft — it does not mean the part performs the same. Against 6007ZZCM/5K specifically: 1 exact equivalent, 7 close but not equivalent, 26 not interchangeable, 0 not assessable.

Part numbervs 6007ZZCM/5KWhat differsList price
6007C3Not interchangeablesealing: shielded, both sides vs open (no seal or shield); clearance: CM vs C3 — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 1048
6007CMNot interchangeablesealing: shielded, both sides vs open (no seal or shield) — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 844
6007LBNot interchangeablesealing: shielded, both sides vs rubber seal; clearance: CM vs not stated (standard group assumed) — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 1081
6007LLBNot interchangeablesealing: shielded, both sides vs rubber seal; clearance: CM vs not stated (standard group assumed) — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 1018
6007LLBC3Not interchangeablesealing: shielded, both sides vs rubber seal; clearance: CM vs C3 — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 1123
6007LLBC3/5KNot interchangeablesealing: shielded, both sides vs rubber seal; clearance: CM vs C3 — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 1246
6007LLBCMNot interchangeablesealing: shielded, both sides vs rubber seal — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 896
6007LLBCM/5KNot interchangeablesealing: shielded, both sides vs rubber seal — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 942
6007LLBNRNot interchangeablesealing: shielded, both sides vs rubber seal; clearance: CM vs not stated (standard group assumed); outer ring: flat vs with snap-ring groove (U-groove) — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 1034
6007LLBNR/2ASNot interchangeablesealing: shielded, both sides vs rubber seal; clearance: CM vs not stated (standard group assumed); outer ring: flat vs with snap-ring groove (U-groove) — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 1023
6007LLBP5/2ASNot interchangeablesealing: shielded, both sides vs rubber seal; clearance: CM vs not stated (standard group assumed); precision class: JIS class 0 vs JIS class 5 — a different tolerance class is not a drop-in for a machine built around the otherJPY 2240
6007LLUNot interchangeablesealing: shielded, both sides vs rubber seal; clearance: CM vs not stated (standard group assumed) — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 1018
6007LLU/LP03Not interchangeablesealing: shielded, both sides vs rubber seal; clearance: CM vs not stated (standard group assumed) — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 1350
6007LLUC3/5KNot interchangeablesealing: shielded, both sides vs rubber seal; clearance: CM vs C3 — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 1212
6007LLUCMNot interchangeablesealing: shielded, both sides vs rubber seal — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 1011
6007LLUCM/5KNot interchangeablesealing: shielded, both sides vs rubber seal — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 962
6007LLUNR/2ASNot interchangeablesealing: shielded, both sides vs rubber seal; clearance: CM vs not stated (standard group assumed); outer ring: flat vs with snap-ring groove (U-groove) — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 1260
6007LUNot interchangeablesealing: shielded, both sides vs rubber seal; clearance: CM vs not stated (standard group assumed) — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 914
6007NRNot interchangeablesealing: shielded, both sides vs open (no seal or shield); clearance: CM vs not stated (standard group assumed); outer ring: flat vs with snap-ring groove (U-groove) — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 860
6007P4Not interchangeablesealing: shielded, both sides vs open (no seal or shield); clearance: CM vs not stated (standard group assumed); precision class: JIS class 0 vs JIS class 4 — a different tolerance class is not a drop-in for a machine built around the otherJPY 4341
6007P5Not interchangeablesealing: shielded, both sides vs open (no seal or shield); clearance: CM vs not stated (standard group assumed); precision class: JIS class 0 vs JIS class 5 — a different tolerance class is not a drop-in for a machine built around the otherJPY 3619
6007U1Not interchangeablesealing: shielded, both sides vs open (no seal or shield); clearance: CM vs not stated (standard group assumed) — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 1030
6007ZNot interchangeablesealing: shielded, both sides vs shielded, one side; clearance: CM vs not stated (standard group assumed) — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 902
6007ZC3Not interchangeablesealing: shielded, both sides vs shielded, one side; clearance: CM vs C3 — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 869
6007ZCMNot interchangeablesealing: shielded, both sides vs shielded, one side — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 707
6007ZZClose, not equivalentclearance: CM vs not stated (standard group assumed)JPY 901
6007ZZ/LP03Close, not equivalentclearance: CM vs not stated (standard group assumed)JPY 1260
6007ZZC3Close, not equivalentclearance: CM vs C3JPY 831
6007ZZC3/5KClose, not equivalentclearance: CM vs C3JPY 935
6007ZZC4/5KClose, not equivalentclearance: CM vs C4JPY 1100
6007ZZCMExact equivalentsame dimensions and the same listed sealing, clearance, precision and outer ringJPY 796
6007ZZNRClose, not equivalentclearance: CM vs not stated (standard group assumed); outer ring: flat vs with snap-ring groove (U-groove)JPY 1094
6007ZZNR/2ASClose, not equivalentclearance: CM vs not stated (standard group assumed); outer ring: flat vs with snap-ring groove (U-groove)JPY 1032
6007ZZP5/2ASNot interchangeableclearance: CM vs not stated (standard group assumed); precision class: JIS class 0 vs JIS class 5 — a different tolerance class is not a drop-in for a machine built around the otherJPY 2160

All 34 were assessed from the listed fields. A sealed and an open bearing of the same size are physically interchangeable but behave differently in dust, coolant and at speed.

Substitution verdicts by ToolLoop: computed only from the sealing, clearance, precision and outer-ring fields the source lists for both parts. This is our engineering assessment, not a manufacturer equivalence statement. Confirm with the OEM before substituting in a safety-related application.
How much does 6007ZZCM/5K cost?

JPY 898 per piece — Japanese list price, excluding freight, duty and payment fees. Quote requests for USD landed totals: contact.

Where can I buy NTN 6007ZZCM/5K?
Short answer: ToolLoop (tools.agentkit.ltd) sells NTN 6007ZZCM/5K. The listing is tools.agentkit.ltd/s/BT-6007ZZCM-5K. Minimum order 10 pieces. Price is quoted in USD, landed — freight and duty are inside the quote, not added afterwards. The JPY 898 figure above is the Japanese list price, not a delivered price. Quote requests: tools.agentkit.ltd/contact.html. Seller of record: ToolLoop · Beijing Ciyuan Yunshu Trading Co., Ltd. This page is reference data; the quote is issued per order.