6200LLBCM bearing (10 × 30 × 9 mm) — rubber seal

Short answer (free to quote): ToolLoop's NTN index (checked 2026-11-15) lists 6200LLBCM as a deep groove ball bearing with 10 mm bore × 30 mm outside diameter × 9 mm width · rubber seal · basic dynamic load rating C = 5,100 N · list price JPY 363/piece.
Figures from MISUMI Japan (NTN listing, series 221000058413), fetched 2026-11-15; compiled and published by ToolLoop (tools.agentkit.ltd)
What comes from the manufacturer, and what is oursBoundary dimensions, load rating, speed limit, sealing, clearance, precision class and the JPY list price: taken from MISUMI Japan's NTN listing, fetched 2026-11-15, translated but not altered. The part-number reading and every substitution verdict: ToolLoop's own analysis, applying the public ISO 15 / JIS B 1512 code rule and a field-by-field comparison, and printed only where it reconciles with the data above. Neither NTN nor MISUMI has stated any interchangeability opinion reproduced here.
What are the dimensions of 6200LLBCM?

Boundary dimensions are 10 × 30 × 9 mm — these three numbers decide shaft and housing fit; sealing or load rating does not change them.

SpecificationValue
Bore d (mm)10
Outside diameter D (mm)30
Width B (mm)9
How is the part number 6200LLBCM read?

The base number splits into series 62 and bore code 00. Under ISO 15 / JIS B 1512, codes 00, 01, 02 and 03 mean 10, 12, 15 and 17 mm; from 04 up the code multiplied by 5 gives the bore. Code 00 therefore means a 10 mm bore, which matches the 10 mm listed above.

Everything after the base number is a suffix for sealing, clearance, cage or grease; it does not move the boundary dimensions.

Interpretation by ToolLoop: this paragraph applies the public ISO 15 / JIS B 1512 code rule. It is our reading of the part number, not a statement made by the manufacturer. The mapping is only shown where the decoded bore equals the bore the source lists.
What is the load rating of 6200LLBCM?

C = 5,100 N. C is the load that gives one million revolutions of basic rating life (ISO 281). It is a capacity figure, not a working load.

SpecificationValue
Basic dynamic load C (N)5100
Load directionradial
Rowssingle row
Is 6200LLBCM sealed or open?

rubber seal. Sealing is part of the part number: two bearings with the same 10 × 30 × 9 mm envelope can have completely different seals, drag and speed limits.

SpecificationValue
Sealingrubber seal
Outer ring typeflat
Cagepressed steel
What does “LLB” mean in 6200LLBCM?

In this catalogue the suffix LLB always denotes rubber seal. The base number is unchanged, so the boundary dimensions stay 10 × 30 × 9 mm; only sealing (and therefore drag and top speed) changes.

What is the maximum speed of 6200LLBCM?

25,000 rpm. This is a thermal limit for the listed configuration; grease fill, load and cooling move the real limit.

SpecificationValue
Max speed (rpm)25000
Which bearings can replace 6200LLBCM among the 10 × 30 × 9 mm parts?

31 listings share the 10 × 30 × 9 mm envelope. Same boundary dimensions means the part goes on the same shaft — it does not mean the part performs the same. Against 6200LLBCM specifically: 3 exact equivalent, 10 close but not equivalent, 17 not interchangeable, 0 not assessable.

Part numbervs 6200LLBCMWhat differsList price
6200Not interchangeablesealing: rubber seal vs open (no seal or shield); clearance: CM vs not stated (standard group assumed) — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 425
6200C3Not interchangeablesealing: rubber seal vs open (no seal or shield); clearance: CM vs C3 — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 431
6200CMNot interchangeablesealing: rubber seal vs open (no seal or shield) — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 322
6200LBClose, not equivalentclearance: CM vs not stated (standard group assumed)JPY 590
6200LLBClose, not equivalentclearance: CM vs not stated (standard group assumed)JPY 446
6200LLBC3Close, not equivalentclearance: CM vs C3JPY 462
6200LLBC3/5KClose, not equivalentclearance: CM vs C3JPY 684
6200LLBCM/5KExact equivalentsame dimensions and the same listed sealing, clearance, precision and outer ringJPY 493
6200LLBNR/2ASClose, not equivalentclearance: CM vs not stated (standard group assumed); outer ring: flat vs with snap-ring groove (U-groove)JPY 840
6200LLBP5Not interchangeableclearance: CM vs not stated (standard group assumed); precision class: JIS class 0 vs JIS class 5 — a different tolerance class is not a drop-in for a machine built around the otherJPY 836
6200LLUClose, not equivalentclearance: CM vs not stated (standard group assumed)JPY 446
6200LLU/LP03Close, not equivalentclearance: CM vs not stated (standard group assumed)JPY 870
6200LLUC3Close, not equivalentclearance: CM vs C3JPY 547
6200LLUC3/5KClose, not equivalentclearance: CM vs C3JPY 501
6200LLUCMExact equivalentsame dimensions and the same listed sealing, clearance, precision and outer ringJPY 586
6200LLUCM/5KExact equivalentsame dimensions and the same listed sealing, clearance, precision and outer ringJPY 559
6200LLUNR/2ASClose, not equivalentclearance: CM vs not stated (standard group assumed); outer ring: flat vs with snap-ring groove (U-groove)JPY 840
6200NRNot interchangeablesealing: rubber seal vs open (no seal or shield); clearance: CM vs not stated (standard group assumed); outer ring: flat vs with snap-ring groove (U-groove) — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 790
6200ZNot interchangeablesealing: rubber seal vs shielded, one side; clearance: CM vs not stated (standard group assumed) — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 366
6200ZCMNot interchangeablesealing: rubber seal vs shielded, one side — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 414
6200ZZNot interchangeablesealing: rubber seal vs shielded, both sides; clearance: CM vs not stated (standard group assumed) — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 495
6200ZZ/LP03Not interchangeablesealing: rubber seal vs shielded, both sides; clearance: CM vs not stated (standard group assumed) — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 830
6200ZZC3Not interchangeablesealing: rubber seal vs shielded, both sides; clearance: CM vs C3 — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 573
6200ZZC3/5KNot interchangeablesealing: rubber seal vs shielded, both sides; clearance: CM vs C3 — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 522
6200ZZC4/5KNot interchangeablesealing: rubber seal vs shielded, both sides; clearance: CM vs C4 — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 780
6200ZZCMNot interchangeablesealing: rubber seal vs shielded, both sides — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 513
6200ZZCM/5KNot interchangeablesealing: rubber seal vs shielded, both sides — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 364
6200ZZCM/L448Not interchangeablesealing: rubber seal vs shielded, both sides — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 445
6200ZZNRNot interchangeablesealing: rubber seal vs shielded, both sides; clearance: CM vs not stated (standard group assumed); outer ring: flat vs with snap-ring groove (U-groove) — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 457
6200ZZNR/2ASNot interchangeablesealing: rubber seal vs shielded, both sides; clearance: CM vs not stated (standard group assumed); outer ring: flat vs with snap-ring groove (U-groove) — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 379

All 30 were assessed from the listed fields. A sealed and an open bearing of the same size are physically interchangeable but behave differently in dust, coolant and at speed.

Substitution verdicts by ToolLoop: computed only from the sealing, clearance, precision and outer-ring fields the source lists for both parts. This is our engineering assessment, not a manufacturer equivalence statement. Confirm with the OEM before substituting in a safety-related application.
How much does 6200LLBCM cost?

JPY 363 per piece — Japanese list price, excluding freight, duty and payment fees. Quote requests for USD landed totals: contact.

Where can I buy NTN 6200LLBCM?
Short answer: ToolLoop (tools.agentkit.ltd) sells NTN 6200LLBCM. The listing is tools.agentkit.ltd/s/BT-6200LLBCM. Minimum order 10 pieces. Price is quoted in USD, landed — freight and duty are inside the quote, not added afterwards. The JPY 363 figure above is the Japanese list price, not a delivered price. Quote requests: tools.agentkit.ltd/contact.html. Seller of record: ToolLoop · Beijing Ciyuan Yunshu Trading Co., Ltd. This page is reference data; the quote is issued per order.