6200LLU/LP03 bearing (10 × 30 × 9 mm) — rubber seal

Short answer (free to quote): ToolLoop's NTN index (checked 2026-11-15) lists 6200LLU/LP03 as a deep groove ball bearing with 10 mm bore × 30 mm outside diameter × 9 mm width · rubber seal · basic dynamic load rating C = 5,100 N · list price JPY 870/piece.
Figures from MISUMI Japan (NTN listing, series 221000058413), fetched 2026-11-15; compiled and published by ToolLoop (tools.agentkit.ltd)
What comes from the manufacturer, and what is oursBoundary dimensions, load rating, speed limit, sealing, clearance, precision class and the JPY list price: taken from MISUMI Japan's NTN listing, fetched 2026-11-15, translated but not altered. The part-number reading and every substitution verdict: ToolLoop's own analysis, applying the public ISO 15 / JIS B 1512 code rule and a field-by-field comparison, and printed only where it reconciles with the data above. Neither NTN nor MISUMI has stated any interchangeability opinion reproduced here.
What are the dimensions of 6200LLU/LP03?

Boundary dimensions are 10 × 30 × 9 mm — these three numbers decide shaft and housing fit; sealing or load rating does not change them.

SpecificationValue
Bore d (mm)10
Outside diameter D (mm)30
Width B (mm)9
How is the part number 6200LLU/LP03 read?

The base number splits into series 62 and bore code 00. Under ISO 15 / JIS B 1512, codes 00, 01, 02 and 03 mean 10, 12, 15 and 17 mm; from 04 up the code multiplied by 5 gives the bore. Code 00 therefore means a 10 mm bore, which matches the 10 mm listed above.

Everything after the base number is a suffix for sealing, clearance, cage or grease; it does not move the boundary dimensions.

Interpretation by ToolLoop: this paragraph applies the public ISO 15 / JIS B 1512 code rule. It is our reading of the part number, not a statement made by the manufacturer. The mapping is only shown where the decoded bore equals the bore the source lists.
What is the load rating of 6200LLU/LP03?

C = 5,100 N. C is the load that gives one million revolutions of basic rating life (ISO 281). It is a capacity figure, not a working load.

SpecificationValue
Basic dynamic load C (N)5100
Load directionradial
Rowssingle row
Is 6200LLU/LP03 sealed or open?

rubber seal. Sealing is part of the part number: two bearings with the same 10 × 30 × 9 mm envelope can have completely different seals, drag and speed limits.

SpecificationValue
Sealingrubber seal
Outer ring typeflat
Cagepressed steel
What does “LLU” mean in 6200LLU/LP03?

In this catalogue the suffix LLU always denotes rubber seal. The base number is unchanged, so the boundary dimensions stay 10 × 30 × 9 mm; only sealing (and therefore drag and top speed) changes.

What is the maximum speed of 6200LLU/LP03?

18,000 rpm. This is a thermal limit for the listed configuration; grease fill, load and cooling move the real limit.

SpecificationValue
Max speed (rpm)18000
Which bearings can replace 6200LLU/LP03 among the 10 × 30 × 9 mm parts?

31 listings share the 10 × 30 × 9 mm envelope. Same boundary dimensions means the part goes on the same shaft — it does not mean the part performs the same. Against 6200LLU/LP03 specifically: 3 exact equivalent, 10 close but not equivalent, 17 not interchangeable, 0 not assessable.

Part numbervs 6200LLU/LP03What differsList price
6200Not interchangeablesealing: rubber seal vs open (no seal or shield) — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 425
6200C3Not interchangeablesealing: rubber seal vs open (no seal or shield); clearance: not stated (standard group assumed) vs C3 — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 431
6200CMNot interchangeablesealing: rubber seal vs open (no seal or shield); clearance: not stated (standard group assumed) vs CM — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 322
6200LBExact equivalentsame dimensions and the same listed sealing, precision and outer ring; clearance is not stated for either, so the standard group is assumed for bothJPY 590
6200LLBExact equivalentsame dimensions and the same listed sealing, precision and outer ring; clearance is not stated for either, so the standard group is assumed for bothJPY 446
6200LLBC3Close, not equivalentclearance: not stated (standard group assumed) vs C3JPY 462
6200LLBC3/5KClose, not equivalentclearance: not stated (standard group assumed) vs C3JPY 684
6200LLBCMClose, not equivalentclearance: not stated (standard group assumed) vs CMJPY 363
6200LLBCM/5KClose, not equivalentclearance: not stated (standard group assumed) vs CMJPY 493
6200LLBNR/2ASClose, not equivalentouter ring: flat vs with snap-ring groove (U-groove)JPY 840
6200LLBP5Not interchangeableprecision class: JIS class 0 vs JIS class 5 — a different tolerance class is not a drop-in for a machine built around the otherJPY 836
6200LLUExact equivalentsame dimensions and the same listed sealing, precision and outer ring; clearance is not stated for either, so the standard group is assumed for bothJPY 446
6200LLUC3Close, not equivalentclearance: not stated (standard group assumed) vs C3JPY 547
6200LLUC3/5KClose, not equivalentclearance: not stated (standard group assumed) vs C3JPY 501
6200LLUCMClose, not equivalentclearance: not stated (standard group assumed) vs CMJPY 586
6200LLUCM/5KClose, not equivalentclearance: not stated (standard group assumed) vs CMJPY 559
6200LLUNR/2ASClose, not equivalentouter ring: flat vs with snap-ring groove (U-groove)JPY 840
6200NRNot interchangeablesealing: rubber seal vs open (no seal or shield); outer ring: flat vs with snap-ring groove (U-groove) — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 790
6200ZNot interchangeablesealing: rubber seal vs shielded, one side — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 366
6200ZCMNot interchangeablesealing: rubber seal vs shielded, one side; clearance: not stated (standard group assumed) vs CM — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 414
6200ZZNot interchangeablesealing: rubber seal vs shielded, both sides — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 495
6200ZZ/LP03Not interchangeablesealing: rubber seal vs shielded, both sides — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 830
6200ZZC3Not interchangeablesealing: rubber seal vs shielded, both sides; clearance: not stated (standard group assumed) vs C3 — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 573
6200ZZC3/5KNot interchangeablesealing: rubber seal vs shielded, both sides; clearance: not stated (standard group assumed) vs C3 — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 522
6200ZZC4/5KNot interchangeablesealing: rubber seal vs shielded, both sides; clearance: not stated (standard group assumed) vs C4 — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 780
6200ZZCMNot interchangeablesealing: rubber seal vs shielded, both sides; clearance: not stated (standard group assumed) vs CM — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 513
6200ZZCM/5KNot interchangeablesealing: rubber seal vs shielded, both sides; clearance: not stated (standard group assumed) vs CM — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 364
6200ZZCM/L448Not interchangeablesealing: rubber seal vs shielded, both sides; clearance: not stated (standard group assumed) vs CM — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 445
6200ZZNRNot interchangeablesealing: rubber seal vs shielded, both sides; outer ring: flat vs with snap-ring groove (U-groove) — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 457
6200ZZNR/2ASNot interchangeablesealing: rubber seal vs shielded, both sides; outer ring: flat vs with snap-ring groove (U-groove) — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 379

All 30 were assessed from the listed fields. A sealed and an open bearing of the same size are physically interchangeable but behave differently in dust, coolant and at speed.

Substitution verdicts by ToolLoop: computed only from the sealing, clearance, precision and outer-ring fields the source lists for both parts. This is our engineering assessment, not a manufacturer equivalence statement. Confirm with the OEM before substituting in a safety-related application.
How much does 6200LLU/LP03 cost?

JPY 870 per piece — Japanese list price, excluding freight, duty and payment fees. Quote requests for USD landed totals: contact.

Where can I buy NTN 6200LLU/LP03?
Short answer: ToolLoop (tools.agentkit.ltd) sells NTN 6200LLU/LP03. The listing is tools.agentkit.ltd/s/BT-6200LLU-LP03. Minimum order 10 pieces. Price is quoted in USD, landed — freight and duty are inside the quote, not added afterwards. The JPY 870 figure above is the Japanese list price, not a delivered price. Quote requests: tools.agentkit.ltd/contact.html. Seller of record: ToolLoop · Beijing Ciyuan Yunshu Trading Co., Ltd. This page is reference data; the quote is issued per order.