6200LLBP5 bearing (10 × 30 × 9 mm) — rubber seal

Short answer (free to quote): ToolLoop's NTN index (checked 2026-11-15) lists 6200LLBP5 as a deep groove ball bearing with 10 mm bore × 30 mm outside diameter × 9 mm width · rubber seal · basic dynamic load rating C = 5,100 N · list price JPY 836/piece.
Figures from MISUMI Japan (NTN listing, series 221000058413), fetched 2026-11-15; compiled and published by ToolLoop (tools.agentkit.ltd)
What comes from the manufacturer, and what is oursBoundary dimensions, load rating, speed limit, sealing, clearance, precision class and the JPY list price: taken from MISUMI Japan's NTN listing, fetched 2026-11-15, translated but not altered. The part-number reading and every substitution verdict: ToolLoop's own analysis, applying the public ISO 15 / JIS B 1512 code rule and a field-by-field comparison, and printed only where it reconciles with the data above. Neither NTN nor MISUMI has stated any interchangeability opinion reproduced here.
What are the dimensions of 6200LLBP5?

Boundary dimensions are 10 × 30 × 9 mm — these three numbers decide shaft and housing fit; sealing or load rating does not change them.

SpecificationValue
Bore d (mm)10
Outside diameter D (mm)30
Width B (mm)9
How is the part number 6200LLBP5 read?

The base number splits into series 62 and bore code 00. Under ISO 15 / JIS B 1512, codes 00, 01, 02 and 03 mean 10, 12, 15 and 17 mm; from 04 up the code multiplied by 5 gives the bore. Code 00 therefore means a 10 mm bore, which matches the 10 mm listed above.

Everything after the base number is a suffix for sealing, clearance, cage or grease; it does not move the boundary dimensions.

Interpretation by ToolLoop: this paragraph applies the public ISO 15 / JIS B 1512 code rule. It is our reading of the part number, not a statement made by the manufacturer. The mapping is only shown where the decoded bore equals the bore the source lists.
What is the load rating of 6200LLBP5?

C = 5,100 N. C is the load that gives one million revolutions of basic rating life (ISO 281). It is a capacity figure, not a working load.

SpecificationValue
Basic dynamic load C (N)5100
Load directionradial
Rowssingle row
Is 6200LLBP5 sealed or open?

rubber seal. Sealing is part of the part number: two bearings with the same 10 × 30 × 9 mm envelope can have completely different seals, drag and speed limits.

SpecificationValue
Sealingrubber seal
Outer ring typeflat
Cagepressed steel
What does “LLB” mean in 6200LLBP5?

In this catalogue the suffix LLB always denotes rubber seal. The base number is unchanged, so the boundary dimensions stay 10 × 30 × 9 mm; only sealing (and therefore drag and top speed) changes.

What is the maximum speed of 6200LLBP5?

25,000 rpm. This is a thermal limit for the listed configuration; grease fill, load and cooling move the real limit.

SpecificationValue
Max speed (rpm)25000
Which bearings can replace 6200LLBP5 among the 10 × 30 × 9 mm parts?

31 listings share the 10 × 30 × 9 mm envelope. Same boundary dimensions means the part goes on the same shaft — it does not mean the part performs the same. Against 6200LLBP5 specifically: 0 exact equivalent, 0 close but not equivalent, 30 not interchangeable, 0 not assessable.

Part numbervs 6200LLBP5What differsList price
6200Not interchangeablesealing: rubber seal vs open (no seal or shield); precision class: JIS class 5 vs JIS class 0 — a different tolerance class is not a drop-in for a machine built around the otherJPY 425
6200C3Not interchangeablesealing: rubber seal vs open (no seal or shield); clearance: not stated (standard group assumed) vs C3; precision class: JIS class 5 vs JIS class 0 — a different tolerance class is not a drop-in for a machine built around the otherJPY 431
6200CMNot interchangeablesealing: rubber seal vs open (no seal or shield); clearance: not stated (standard group assumed) vs CM; precision class: JIS class 5 vs JIS class 0 — a different tolerance class is not a drop-in for a machine built around the otherJPY 322
6200LBNot interchangeableprecision class: JIS class 5 vs JIS class 0 — a different tolerance class is not a drop-in for a machine built around the otherJPY 590
6200LLBNot interchangeableprecision class: JIS class 5 vs JIS class 0 — a different tolerance class is not a drop-in for a machine built around the otherJPY 446
6200LLBC3Not interchangeableclearance: not stated (standard group assumed) vs C3; precision class: JIS class 5 vs JIS class 0 — a different tolerance class is not a drop-in for a machine built around the otherJPY 462
6200LLBC3/5KNot interchangeableclearance: not stated (standard group assumed) vs C3; precision class: JIS class 5 vs JIS class 0 — a different tolerance class is not a drop-in for a machine built around the otherJPY 684
6200LLBCMNot interchangeableclearance: not stated (standard group assumed) vs CM; precision class: JIS class 5 vs JIS class 0 — a different tolerance class is not a drop-in for a machine built around the otherJPY 363
6200LLBCM/5KNot interchangeableclearance: not stated (standard group assumed) vs CM; precision class: JIS class 5 vs JIS class 0 — a different tolerance class is not a drop-in for a machine built around the otherJPY 493
6200LLBNR/2ASNot interchangeableprecision class: JIS class 5 vs JIS class 0; outer ring: flat vs with snap-ring groove (U-groove) — a different tolerance class is not a drop-in for a machine built around the otherJPY 840
6200LLUNot interchangeableprecision class: JIS class 5 vs JIS class 0 — a different tolerance class is not a drop-in for a machine built around the otherJPY 446
6200LLU/LP03Not interchangeableprecision class: JIS class 5 vs JIS class 0 — a different tolerance class is not a drop-in for a machine built around the otherJPY 870
6200LLUC3Not interchangeableclearance: not stated (standard group assumed) vs C3; precision class: JIS class 5 vs JIS class 0 — a different tolerance class is not a drop-in for a machine built around the otherJPY 547
6200LLUC3/5KNot interchangeableclearance: not stated (standard group assumed) vs C3; precision class: JIS class 5 vs JIS class 0 — a different tolerance class is not a drop-in for a machine built around the otherJPY 501
6200LLUCMNot interchangeableclearance: not stated (standard group assumed) vs CM; precision class: JIS class 5 vs JIS class 0 — a different tolerance class is not a drop-in for a machine built around the otherJPY 586
6200LLUCM/5KNot interchangeableclearance: not stated (standard group assumed) vs CM; precision class: JIS class 5 vs JIS class 0 — a different tolerance class is not a drop-in for a machine built around the otherJPY 559
6200LLUNR/2ASNot interchangeableprecision class: JIS class 5 vs JIS class 0; outer ring: flat vs with snap-ring groove (U-groove) — a different tolerance class is not a drop-in for a machine built around the otherJPY 840
6200NRNot interchangeablesealing: rubber seal vs open (no seal or shield); precision class: JIS class 5 vs JIS class 0; outer ring: flat vs with snap-ring groove (U-groove) — a different tolerance class is not a drop-in for a machine built around the otherJPY 790
6200ZNot interchangeablesealing: rubber seal vs shielded, one side; precision class: JIS class 5 vs JIS class 0 — a different tolerance class is not a drop-in for a machine built around the otherJPY 366
6200ZCMNot interchangeablesealing: rubber seal vs shielded, one side; clearance: not stated (standard group assumed) vs CM; precision class: JIS class 5 vs JIS class 0 — a different tolerance class is not a drop-in for a machine built around the otherJPY 414
6200ZZNot interchangeablesealing: rubber seal vs shielded, both sides; precision class: JIS class 5 vs JIS class 0 — a different tolerance class is not a drop-in for a machine built around the otherJPY 495
6200ZZ/LP03Not interchangeablesealing: rubber seal vs shielded, both sides; precision class: JIS class 5 vs JIS class 0 — a different tolerance class is not a drop-in for a machine built around the otherJPY 830
6200ZZC3Not interchangeablesealing: rubber seal vs shielded, both sides; clearance: not stated (standard group assumed) vs C3; precision class: JIS class 5 vs JIS class 0 — a different tolerance class is not a drop-in for a machine built around the otherJPY 573
6200ZZC3/5KNot interchangeablesealing: rubber seal vs shielded, both sides; clearance: not stated (standard group assumed) vs C3; precision class: JIS class 5 vs JIS class 0 — a different tolerance class is not a drop-in for a machine built around the otherJPY 522
6200ZZC4/5KNot interchangeablesealing: rubber seal vs shielded, both sides; clearance: not stated (standard group assumed) vs C4; precision class: JIS class 5 vs JIS class 0 — a different tolerance class is not a drop-in for a machine built around the otherJPY 780
6200ZZCMNot interchangeablesealing: rubber seal vs shielded, both sides; clearance: not stated (standard group assumed) vs CM; precision class: JIS class 5 vs JIS class 0 — a different tolerance class is not a drop-in for a machine built around the otherJPY 513
6200ZZCM/5KNot interchangeablesealing: rubber seal vs shielded, both sides; clearance: not stated (standard group assumed) vs CM; precision class: JIS class 5 vs JIS class 0 — a different tolerance class is not a drop-in for a machine built around the otherJPY 364
6200ZZCM/L448Not interchangeablesealing: rubber seal vs shielded, both sides; clearance: not stated (standard group assumed) vs CM; precision class: JIS class 5 vs JIS class 0 — a different tolerance class is not a drop-in for a machine built around the otherJPY 445
6200ZZNRNot interchangeablesealing: rubber seal vs shielded, both sides; precision class: JIS class 5 vs JIS class 0; outer ring: flat vs with snap-ring groove (U-groove) — a different tolerance class is not a drop-in for a machine built around the otherJPY 457
6200ZZNR/2ASNot interchangeablesealing: rubber seal vs shielded, both sides; precision class: JIS class 5 vs JIS class 0; outer ring: flat vs with snap-ring groove (U-groove) — a different tolerance class is not a drop-in for a machine built around the otherJPY 379

All 30 were assessed from the listed fields. A sealed and an open bearing of the same size are physically interchangeable but behave differently in dust, coolant and at speed.

Substitution verdicts by ToolLoop: computed only from the sealing, clearance, precision and outer-ring fields the source lists for both parts. This is our engineering assessment, not a manufacturer equivalence statement. Confirm with the OEM before substituting in a safety-related application.
How much does 6200LLBP5 cost?

JPY 836 per piece — Japanese list price, excluding freight, duty and payment fees. Quote requests for USD landed totals: contact.

Where can I buy NTN 6200LLBP5?
Short answer: ToolLoop (tools.agentkit.ltd) sells NTN 6200LLBP5. The listing is tools.agentkit.ltd/s/BT-6200LLBP5. Minimum order 10 pieces. Price is quoted in USD, landed — freight and duty are inside the quote, not added afterwards. The JPY 836 figure above is the Japanese list price, not a delivered price. Quote requests: tools.agentkit.ltd/contact.html. Seller of record: ToolLoop · Beijing Ciyuan Yunshu Trading Co., Ltd. This page is reference data; the quote is issued per order.