6201LLUCM bearing (12 × 32 × 10 mm) — rubber seal

Short answer (free to quote): ToolLoop's NTN index (checked 2026-11-15) lists 6201LLUCM as a deep groove ball bearing with 12 mm bore × 32 mm outside diameter × 10 mm width · rubber seal · basic dynamic load rating C = 6,100 N · list price JPY 628/piece.
Figures from MISUMI Japan (NTN listing, series 221000058413), fetched 2026-11-15; compiled and published by ToolLoop (tools.agentkit.ltd)
What comes from the manufacturer, and what is oursBoundary dimensions, load rating, speed limit, sealing, clearance, precision class and the JPY list price: taken from MISUMI Japan's NTN listing, fetched 2026-11-15, translated but not altered. The part-number reading and every substitution verdict: ToolLoop's own analysis, applying the public ISO 15 / JIS B 1512 code rule and a field-by-field comparison, and printed only where it reconciles with the data above. Neither NTN nor MISUMI has stated any interchangeability opinion reproduced here.
What are the dimensions of 6201LLUCM?

Boundary dimensions are 12 × 32 × 10 mm — these three numbers decide shaft and housing fit; sealing or load rating does not change them.

SpecificationValue
Bore d (mm)12
Outside diameter D (mm)32
Width B (mm)10
How is the part number 6201LLUCM read?

The base number splits into series 62 and bore code 01. Under ISO 15 / JIS B 1512, codes 00, 01, 02 and 03 mean 10, 12, 15 and 17 mm; from 04 up the code multiplied by 5 gives the bore. Code 01 therefore means a 12 mm bore, which matches the 12 mm listed above.

Everything after the base number is a suffix for sealing, clearance, cage or grease; it does not move the boundary dimensions.

Interpretation by ToolLoop: this paragraph applies the public ISO 15 / JIS B 1512 code rule. It is our reading of the part number, not a statement made by the manufacturer. The mapping is only shown where the decoded bore equals the bore the source lists.
What is the load rating of 6201LLUCM?

C = 6,100 N. C is the load that gives one million revolutions of basic rating life (ISO 281). It is a capacity figure, not a working load.

SpecificationValue
Basic dynamic load C (N)6100
Load directionradial
Rowssingle row
Is 6201LLUCM sealed or open?

rubber seal. Sealing is part of the part number: two bearings with the same 12 × 32 × 10 mm envelope can have completely different seals, drag and speed limits.

SpecificationValue
Sealingrubber seal
Outer ring typeflat
Cagepressed steel
What does “LLU” mean in 6201LLUCM?

In this catalogue the suffix LLU always denotes rubber seal. The base number is unchanged, so the boundary dimensions stay 12 × 32 × 10 mm; only sealing (and therefore drag and top speed) changes.

What is the maximum speed of 6201LLUCM?

16,000 rpm. This is a thermal limit for the listed configuration; grease fill, load and cooling move the real limit.

SpecificationValue
Max speed (rpm)16000
Which bearings can replace 6201LLUCM among the 12 × 32 × 10 mm parts?

35 listings share the 12 × 32 × 10 mm envelope. Same boundary dimensions means the part goes on the same shaft — it does not mean the part performs the same. Against 6201LLUCM specifically: 3 exact equivalent, 12 close but not equivalent, 19 not interchangeable, 0 not assessable.

Part numbervs 6201LLUCMWhat differsList price
6201Not interchangeablesealing: rubber seal vs open (no seal or shield); clearance: CM vs not stated (standard group assumed) — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 454
6201C3Not interchangeablesealing: rubber seal vs open (no seal or shield); clearance: CM vs C3 — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 513
6201CMNot interchangeablesealing: rubber seal vs open (no seal or shield) — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 339
6201LBClose, not equivalentclearance: CM vs not stated (standard group assumed)JPY 604
6201LLBClose, not equivalentclearance: CM vs not stated (standard group assumed)JPY 680
6201LLBC3Close, not equivalentclearance: CM vs C3JPY 596
6201LLBC3/5KClose, not equivalentclearance: CM vs C3JPY 667
6201LLBCMExact equivalentsame dimensions and the same listed sealing, clearance, precision and outer ringJPY 412
6201LLBCM/5KExact equivalentsame dimensions and the same listed sealing, clearance, precision and outer ringJPY 439
6201LLBNR/2ASClose, not equivalentclearance: CM vs not stated (standard group assumed); outer ring: flat vs with snap-ring groove (U-groove)JPY 860
6201LLUClose, not equivalentclearance: CM vs not stated (standard group assumed)JPY 473
6201LLU/2ASClose, not equivalentclearance: CM vs not stated (standard group assumed)JPY 414
6201LLU/LP03Close, not equivalentclearance: CM vs not stated (standard group assumed)JPY 900
6201LLUC3Close, not equivalentclearance: CM vs C3JPY 628
6201LLUC3/5KClose, not equivalentclearance: CM vs C3JPY 649
6201LLUCM/5KExact equivalentsame dimensions and the same listed sealing, clearance, precision and outer ringJPY 423
6201LLUNR/2ASClose, not equivalentclearance: CM vs not stated (standard group assumed); outer ring: flat vs with snap-ring groove (U-groove)JPY 860
6201LUClose, not equivalentclearance: CM vs not stated (standard group assumed)JPY 627
6201NRNot interchangeablesealing: rubber seal vs open (no seal or shield); clearance: CM vs not stated (standard group assumed); outer ring: flat vs with snap-ring groove (U-groove) — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 800
6201ZNot interchangeablesealing: rubber seal vs shielded, one side; clearance: CM vs not stated (standard group assumed) — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 540
6201ZC3Not interchangeablesealing: rubber seal vs shielded, one side; clearance: CM vs C3 — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 790
6201ZCMNot interchangeablesealing: rubber seal vs shielded, one side — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 443
6201ZNRNot interchangeablesealing: rubber seal vs shielded, one side; clearance: CM vs not stated (standard group assumed); outer ring: flat vs with snap-ring groove (U-groove) — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 784
6201ZZNot interchangeablesealing: rubber seal vs shielded, both sides; clearance: CM vs not stated (standard group assumed) — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 343
6201ZZ/LP03Not interchangeablesealing: rubber seal vs shielded, both sides; clearance: CM vs not stated (standard group assumed) — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 860
6201ZZC3Not interchangeablesealing: rubber seal vs shielded, both sides; clearance: CM vs C3 — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 633
6201ZZC3/5KNot interchangeablesealing: rubber seal vs shielded, both sides; clearance: CM vs C3 — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 358
6201ZZC4Not interchangeablesealing: rubber seal vs shielded, both sides; clearance: CM vs C4 — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 473
6201ZZC4/5KNot interchangeablesealing: rubber seal vs shielded, both sides; clearance: CM vs C4 — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 525
6201ZZCMNot interchangeablesealing: rubber seal vs shielded, both sides — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 537
6201ZZCM/5KNot interchangeablesealing: rubber seal vs shielded, both sides — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 393
6201ZZNRNot interchangeablesealing: rubber seal vs shielded, both sides; clearance: CM vs not stated (standard group assumed); outer ring: flat vs with snap-ring groove (U-groove) — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 395
6201ZZNR/2ASNot interchangeablesealing: rubber seal vs shielded, both sides; clearance: CM vs not stated (standard group assumed); outer ring: flat vs with snap-ring groove (U-groove) — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 547
6201ZZNRC3/5KNot interchangeablesealing: rubber seal vs shielded, both sides; clearance: CM vs C3; outer ring: flat vs with snap-ring groove (U-groove) — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 830

All 34 were assessed from the listed fields. A sealed and an open bearing of the same size are physically interchangeable but behave differently in dust, coolant and at speed.

Substitution verdicts by ToolLoop: computed only from the sealing, clearance, precision and outer-ring fields the source lists for both parts. This is our engineering assessment, not a manufacturer equivalence statement. Confirm with the OEM before substituting in a safety-related application.
How much does 6201LLUCM cost?

JPY 628 per piece — Japanese list price, excluding freight, duty and payment fees. Quote requests for USD landed totals: contact.

Where can I buy NTN 6201LLUCM?
Short answer: ToolLoop (tools.agentkit.ltd) sells NTN 6201LLUCM. The listing is tools.agentkit.ltd/s/BT-6201LLUCM. Minimum order 10 pieces. Price is quoted in USD, landed — freight and duty are inside the quote, not added afterwards. The JPY 628 figure above is the Japanese list price, not a delivered price. Quote requests: tools.agentkit.ltd/contact.html. Seller of record: ToolLoop · Beijing Ciyuan Yunshu Trading Co., Ltd. This page is reference data; the quote is issued per order.