6201ZCM bearing (12 × 32 × 10 mm) — shielded, one side

Short answer (free to quote): ToolLoop's NTN index (checked 2026-11-15) lists 6201ZCM as a deep groove ball bearing with 12 mm bore × 32 mm outside diameter × 10 mm width · shielded, one side · basic dynamic load rating C = 6,100 N · list price JPY 443/piece.
Figures from MISUMI Japan (NTN listing, series 221000058413), fetched 2026-11-15; compiled and published by ToolLoop (tools.agentkit.ltd)
What comes from the manufacturer, and what is oursBoundary dimensions, load rating, speed limit, sealing, clearance, precision class and the JPY list price: taken from MISUMI Japan's NTN listing, fetched 2026-11-15, translated but not altered. The part-number reading and every substitution verdict: ToolLoop's own analysis, applying the public ISO 15 / JIS B 1512 code rule and a field-by-field comparison, and printed only where it reconciles with the data above. Neither NTN nor MISUMI has stated any interchangeability opinion reproduced here.
What are the dimensions of 6201ZCM?

Boundary dimensions are 12 × 32 × 10 mm — these three numbers decide shaft and housing fit; sealing or load rating does not change them.

SpecificationValue
Bore d (mm)12
Outside diameter D (mm)32
Width B (mm)10
How is the part number 6201ZCM read?

The base number splits into series 62 and bore code 01. Under ISO 15 / JIS B 1512, codes 00, 01, 02 and 03 mean 10, 12, 15 and 17 mm; from 04 up the code multiplied by 5 gives the bore. Code 01 therefore means a 12 mm bore, which matches the 12 mm listed above.

Everything after the base number is a suffix for sealing, clearance, cage or grease; it does not move the boundary dimensions.

Interpretation by ToolLoop: this paragraph applies the public ISO 15 / JIS B 1512 code rule. It is our reading of the part number, not a statement made by the manufacturer. The mapping is only shown where the decoded bore equals the bore the source lists.
What is the load rating of 6201ZCM?

C = 6,100 N. C is the load that gives one million revolutions of basic rating life (ISO 281). It is a capacity figure, not a working load.

SpecificationValue
Basic dynamic load C (N)6100
Load directionradial
Rowssingle row
Is 6201ZCM sealed or open?

shielded, one side. Sealing is part of the part number: two bearings with the same 12 × 32 × 10 mm envelope can have completely different seals, drag and speed limits.

SpecificationValue
Sealingshielded, one side
Outer ring typeflat
Cagepressed steel
What does “Z” mean in 6201ZCM?

In this catalogue the suffix Z always denotes shielded, one side. The base number is unchanged, so the boundary dimensions stay 12 × 32 × 10 mm; only sealing (and therefore drag and top speed) changes.

What is the maximum speed of 6201ZCM?

26,000 rpm. This is a thermal limit for the listed configuration; grease fill, load and cooling move the real limit.

SpecificationValue
Max speed (rpm)26000
Which bearings can replace 6201ZCM among the 12 × 32 × 10 mm parts?

35 listings share the 12 × 32 × 10 mm envelope. Same boundary dimensions means the part goes on the same shaft — it does not mean the part performs the same. Against 6201ZCM specifically: 0 exact equivalent, 3 close but not equivalent, 31 not interchangeable, 0 not assessable.

Part numbervs 6201ZCMWhat differsList price
6201Not interchangeablesealing: shielded, one side vs open (no seal or shield); clearance: CM vs not stated (standard group assumed) — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 454
6201C3Not interchangeablesealing: shielded, one side vs open (no seal or shield); clearance: CM vs C3 — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 513
6201CMNot interchangeablesealing: shielded, one side vs open (no seal or shield) — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 339
6201LBNot interchangeablesealing: shielded, one side vs rubber seal; clearance: CM vs not stated (standard group assumed) — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 604
6201LLBNot interchangeablesealing: shielded, one side vs rubber seal; clearance: CM vs not stated (standard group assumed) — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 680
6201LLBC3Not interchangeablesealing: shielded, one side vs rubber seal; clearance: CM vs C3 — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 596
6201LLBC3/5KNot interchangeablesealing: shielded, one side vs rubber seal; clearance: CM vs C3 — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 667
6201LLBCMNot interchangeablesealing: shielded, one side vs rubber seal — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 412
6201LLBCM/5KNot interchangeablesealing: shielded, one side vs rubber seal — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 439
6201LLBNR/2ASNot interchangeablesealing: shielded, one side vs rubber seal; clearance: CM vs not stated (standard group assumed); outer ring: flat vs with snap-ring groove (U-groove) — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 860
6201LLUNot interchangeablesealing: shielded, one side vs rubber seal; clearance: CM vs not stated (standard group assumed) — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 473
6201LLU/2ASNot interchangeablesealing: shielded, one side vs rubber seal; clearance: CM vs not stated (standard group assumed) — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 414
6201LLU/LP03Not interchangeablesealing: shielded, one side vs rubber seal; clearance: CM vs not stated (standard group assumed) — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 900
6201LLUC3Not interchangeablesealing: shielded, one side vs rubber seal; clearance: CM vs C3 — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 628
6201LLUC3/5KNot interchangeablesealing: shielded, one side vs rubber seal; clearance: CM vs C3 — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 649
6201LLUCMNot interchangeablesealing: shielded, one side vs rubber seal — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 628
6201LLUCM/5KNot interchangeablesealing: shielded, one side vs rubber seal — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 423
6201LLUNR/2ASNot interchangeablesealing: shielded, one side vs rubber seal; clearance: CM vs not stated (standard group assumed); outer ring: flat vs with snap-ring groove (U-groove) — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 860
6201LUNot interchangeablesealing: shielded, one side vs rubber seal; clearance: CM vs not stated (standard group assumed) — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 627
6201NRNot interchangeablesealing: shielded, one side vs open (no seal or shield); clearance: CM vs not stated (standard group assumed); outer ring: flat vs with snap-ring groove (U-groove) — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 800
6201ZClose, not equivalentclearance: CM vs not stated (standard group assumed)JPY 540
6201ZC3Close, not equivalentclearance: CM vs C3JPY 790
6201ZNRClose, not equivalentclearance: CM vs not stated (standard group assumed); outer ring: flat vs with snap-ring groove (U-groove)JPY 784
6201ZZNot interchangeablesealing: shielded, one side vs shielded, both sides; clearance: CM vs not stated (standard group assumed) — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 343
6201ZZ/LP03Not interchangeablesealing: shielded, one side vs shielded, both sides; clearance: CM vs not stated (standard group assumed) — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 860
6201ZZC3Not interchangeablesealing: shielded, one side vs shielded, both sides; clearance: CM vs C3 — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 633
6201ZZC3/5KNot interchangeablesealing: shielded, one side vs shielded, both sides; clearance: CM vs C3 — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 358
6201ZZC4Not interchangeablesealing: shielded, one side vs shielded, both sides; clearance: CM vs C4 — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 473
6201ZZC4/5KNot interchangeablesealing: shielded, one side vs shielded, both sides; clearance: CM vs C4 — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 525
6201ZZCMNot interchangeablesealing: shielded, one side vs shielded, both sides — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 537
6201ZZCM/5KNot interchangeablesealing: shielded, one side vs shielded, both sides — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 393
6201ZZNRNot interchangeablesealing: shielded, one side vs shielded, both sides; clearance: CM vs not stated (standard group assumed); outer ring: flat vs with snap-ring groove (U-groove) — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 395
6201ZZNR/2ASNot interchangeablesealing: shielded, one side vs shielded, both sides; clearance: CM vs not stated (standard group assumed); outer ring: flat vs with snap-ring groove (U-groove) — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 547
6201ZZNRC3/5KNot interchangeablesealing: shielded, one side vs shielded, both sides; clearance: CM vs C3; outer ring: flat vs with snap-ring groove (U-groove) — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 830

All 34 were assessed from the listed fields. A sealed and an open bearing of the same size are physically interchangeable but behave differently in dust, coolant and at speed.

Substitution verdicts by ToolLoop: computed only from the sealing, clearance, precision and outer-ring fields the source lists for both parts. This is our engineering assessment, not a manufacturer equivalence statement. Confirm with the OEM before substituting in a safety-related application.
How much does 6201ZCM cost?

JPY 443 per piece — Japanese list price, excluding freight, duty and payment fees. Quote requests for USD landed totals: contact.

Where can I buy NTN 6201ZCM?
Short answer: ToolLoop (tools.agentkit.ltd) sells NTN 6201ZCM. The listing is tools.agentkit.ltd/s/BT-6201ZCM. Minimum order 10 pieces. Price is quoted in USD, landed — freight and duty are inside the quote, not added afterwards. The JPY 443 figure above is the Japanese list price, not a delivered price. Quote requests: tools.agentkit.ltd/contact.html. Seller of record: ToolLoop · Beijing Ciyuan Yunshu Trading Co., Ltd. This page is reference data; the quote is issued per order.