6203ZZP5 bearing (17 × 40 × 12 mm) — shielded, both sides

Short answer (free to quote): ToolLoop's NTN index (checked 2026-11-15) lists 6203ZZP5 as a deep groove ball bearing with 17 mm bore × 40 mm outside diameter × 12 mm width · shielded, both sides · basic dynamic load rating C = 9,600 N · list price JPY 1,247/piece.
Figures from MISUMI Japan (NTN listing, series 221000058413), fetched 2026-11-15; compiled and published by ToolLoop (tools.agentkit.ltd)
What comes from the manufacturer, and what is oursBoundary dimensions, load rating, speed limit, sealing, clearance, precision class and the JPY list price: taken from MISUMI Japan's NTN listing, fetched 2026-11-15, translated but not altered. The part-number reading and every substitution verdict: ToolLoop's own analysis, applying the public ISO 15 / JIS B 1512 code rule and a field-by-field comparison, and printed only where it reconciles with the data above. Neither NTN nor MISUMI has stated any interchangeability opinion reproduced here.
What are the dimensions of 6203ZZP5?

Boundary dimensions are 17 × 40 × 12 mm — these three numbers decide shaft and housing fit; sealing or load rating does not change them.

SpecificationValue
Bore d (mm)17
Outside diameter D (mm)40
Width B (mm)12
How is the part number 6203ZZP5 read?

The base number splits into series 62 and bore code 03. Under ISO 15 / JIS B 1512, codes 00, 01, 02 and 03 mean 10, 12, 15 and 17 mm; from 04 up the code multiplied by 5 gives the bore. Code 03 therefore means a 17 mm bore, which matches the 17 mm listed above.

Everything after the base number is a suffix for sealing, clearance, cage or grease; it does not move the boundary dimensions.

Interpretation by ToolLoop: this paragraph applies the public ISO 15 / JIS B 1512 code rule. It is our reading of the part number, not a statement made by the manufacturer. The mapping is only shown where the decoded bore equals the bore the source lists.
What is the load rating of 6203ZZP5?

C = 9,600 N. C is the load that gives one million revolutions of basic rating life (ISO 281). It is a capacity figure, not a working load.

SpecificationValue
Basic dynamic load C (N)9600
Load directionradial
Rowssingle row
Is 6203ZZP5 sealed or open?

shielded, both sides. Sealing is part of the part number: two bearings with the same 17 × 40 × 12 mm envelope can have completely different seals, drag and speed limits.

SpecificationValue
Sealingshielded, both sides
Outer ring typeflat
Cagepressed steel
What does “ZZ” mean in 6203ZZP5?

In this catalogue the suffix ZZ always denotes shielded, both sides. The base number is unchanged, so the boundary dimensions stay 17 × 40 × 12 mm; only sealing (and therefore drag and top speed) changes.

What is the maximum speed of 6203ZZP5?

18,000 rpm. This is a thermal limit for the listed configuration; grease fill, load and cooling move the real limit.

SpecificationValue
Max speed (rpm)18000
Which bearings can replace 6203ZZP5 among the 17 × 40 × 12 mm parts?

40 listings share the 17 × 40 × 12 mm envelope. Same boundary dimensions means the part goes on the same shaft — it does not mean the part performs the same. Against 6203ZZP5 specifically: 1 exact equivalent, 0 close but not equivalent, 38 not interchangeable, 0 not assessable.

Part numbervs 6203ZZP5What differsList price
6203Not interchangeablesealing: shielded, both sides vs open (no seal or shield); precision class: JIS class 5 vs JIS class 0 — a different tolerance class is not a drop-in for a machine built around the otherJPY 582
6203C3Not interchangeablesealing: shielded, both sides vs open (no seal or shield); clearance: not stated (standard group assumed) vs C3; precision class: JIS class 5 vs JIS class 0 — a different tolerance class is not a drop-in for a machine built around the otherJPY 424
6203C4Not interchangeablesealing: shielded, both sides vs open (no seal or shield); clearance: not stated (standard group assumed) vs C4; precision class: JIS class 5 vs JIS class 0 — a different tolerance class is not a drop-in for a machine built around the otherJPY 443
6203CMNot interchangeablesealing: shielded, both sides vs open (no seal or shield); clearance: not stated (standard group assumed) vs CM; precision class: JIS class 5 vs JIS class 0 — a different tolerance class is not a drop-in for a machine built around the otherJPY 607
6203L1C3Not interchangeablesealing: shielded, both sides vs rubber seal; clearance: not stated (standard group assumed) vs C3; precision class: JIS class 5 vs JIS class 0 — a different tolerance class is not a drop-in for a machine built around the otherJPY 950
6203LBNot interchangeablesealing: shielded, both sides vs rubber seal; precision class: JIS class 5 vs JIS class 0 — a different tolerance class is not a drop-in for a machine built around the otherJPY 728
6203LLBNot interchangeablesealing: shielded, both sides vs rubber seal; precision class: JIS class 5 vs JIS class 0 — a different tolerance class is not a drop-in for a machine built around the otherJPY 771
6203LLB/LP03Not interchangeablesealing: shielded, both sides vs rubber seal; precision class: JIS class 5 vs JIS class 0 — a different tolerance class is not a drop-in for a machine built around the otherJPY 1000
6203LLBC3Not interchangeablesealing: shielded, both sides vs rubber seal; clearance: not stated (standard group assumed) vs C3; precision class: JIS class 5 vs JIS class 0 — a different tolerance class is not a drop-in for a machine built around the otherJPY 715
6203LLBC3/5KNot interchangeablesealing: shielded, both sides vs rubber seal; clearance: not stated (standard group assumed) vs C3; precision class: JIS class 5 vs JIS class 0 — a different tolerance class is not a drop-in for a machine built around the otherJPY 829
6203LLBCMNot interchangeablesealing: shielded, both sides vs rubber seal; clearance: not stated (standard group assumed) vs CM; precision class: JIS class 5 vs JIS class 0 — a different tolerance class is not a drop-in for a machine built around the otherJPY 741
6203LLBCM/5KNot interchangeablesealing: shielded, both sides vs rubber seal; clearance: not stated (standard group assumed) vs CM; precision class: JIS class 5 vs JIS class 0 — a different tolerance class is not a drop-in for a machine built around the otherJPY 747
6203LLUNot interchangeablesealing: shielded, both sides vs rubber seal; precision class: JIS class 5 vs JIS class 0 — a different tolerance class is not a drop-in for a machine built around the otherJPY 748
6203LLU/LP03Not interchangeablesealing: shielded, both sides vs rubber seal; precision class: JIS class 5 vs JIS class 0 — a different tolerance class is not a drop-in for a machine built around the otherJPY 1000
6203LLUC3Not interchangeablesealing: shielded, both sides vs rubber seal; clearance: not stated (standard group assumed) vs C3; precision class: JIS class 5 vs JIS class 0 — a different tolerance class is not a drop-in for a machine built around the otherJPY 728
6203LLUC3/5KNot interchangeablesealing: shielded, both sides vs rubber seal; clearance: not stated (standard group assumed) vs C3; precision class: JIS class 5 vs JIS class 0 — a different tolerance class is not a drop-in for a machine built around the otherJPY 729
6203LLUCMNot interchangeablesealing: shielded, both sides vs rubber seal; clearance: not stated (standard group assumed) vs CM; precision class: JIS class 5 vs JIS class 0 — a different tolerance class is not a drop-in for a machine built around the otherJPY 758
6203LLUCM/5KNot interchangeablesealing: shielded, both sides vs rubber seal; clearance: not stated (standard group assumed) vs CM; precision class: JIS class 5 vs JIS class 0 — a different tolerance class is not a drop-in for a machine built around the otherJPY 707
6203LLUNRNot interchangeablesealing: shielded, both sides vs rubber seal; precision class: JIS class 5 vs JIS class 0; outer ring: flat vs with snap-ring groove (U-groove) — a different tolerance class is not a drop-in for a machine built around the otherJPY 800
6203LLUNR/2ASNot interchangeablesealing: shielded, both sides vs rubber seal; precision class: JIS class 5 vs JIS class 0; outer ring: flat vs with snap-ring groove (U-groove) — a different tolerance class is not a drop-in for a machine built around the otherJPY 729
6203LUNot interchangeablesealing: shielded, both sides vs rubber seal; precision class: JIS class 5 vs JIS class 0 — a different tolerance class is not a drop-in for a machine built around the otherJPY 798
6203NRNot interchangeablesealing: shielded, both sides vs open (no seal or shield); precision class: JIS class 5 vs JIS class 0; outer ring: flat vs with snap-ring groove (U-groove) — a different tolerance class is not a drop-in for a machine built around the otherJPY 870
6203ZNot interchangeablesealing: shielded, both sides vs shielded, one side; precision class: JIS class 5 vs JIS class 0 — a different tolerance class is not a drop-in for a machine built around the otherJPY 692
6203ZC3Not interchangeablesealing: shielded, both sides vs shielded, one side; clearance: not stated (standard group assumed) vs C3; precision class: JIS class 5 vs JIS class 0 — a different tolerance class is not a drop-in for a machine built around the otherJPY 860
6203ZCMNot interchangeablesealing: shielded, both sides vs shielded, one side; clearance: not stated (standard group assumed) vs CM; precision class: JIS class 5 vs JIS class 0 — a different tolerance class is not a drop-in for a machine built around the otherJPY 552
6203ZNRNot interchangeablesealing: shielded, both sides vs shielded, one side; precision class: JIS class 5 vs JIS class 0; outer ring: flat vs with snap-ring groove (U-groove) — a different tolerance class is not a drop-in for a machine built around the otherJPY 684
6203ZZNot interchangeableprecision class: JIS class 5 vs JIS class 0 — a different tolerance class is not a drop-in for a machine built around the otherJPY 454
6203ZZ/LP03Not interchangeableprecision class: JIS class 5 vs JIS class 0 — a different tolerance class is not a drop-in for a machine built around the otherJPY 940
6203ZZC3Not interchangeableclearance: not stated (standard group assumed) vs C3; precision class: JIS class 5 vs JIS class 0 — a different tolerance class is not a drop-in for a machine built around the otherJPY 712
6203ZZC3/5KNot interchangeableclearance: not stated (standard group assumed) vs C3; precision class: JIS class 5 vs JIS class 0 — a different tolerance class is not a drop-in for a machine built around the otherJPY 676
6203ZZC3/L448Not interchangeableclearance: not stated (standard group assumed) vs C3; precision class: JIS class 5 vs JIS class 0 — a different tolerance class is not a drop-in for a machine built around the otherJPY 860
6203ZZC4/5KNot interchangeableclearance: not stated (standard group assumed) vs C4; precision class: JIS class 5 vs JIS class 0 — a different tolerance class is not a drop-in for a machine built around the otherJPY 860
6203ZZCMNot interchangeableclearance: not stated (standard group assumed) vs CM; precision class: JIS class 5 vs JIS class 0 — a different tolerance class is not a drop-in for a machine built around the otherJPY 480
6203ZZCM/5KNot interchangeableclearance: not stated (standard group assumed) vs CM; precision class: JIS class 5 vs JIS class 0 — a different tolerance class is not a drop-in for a machine built around the otherJPY 497
6203ZZCM/L448Not interchangeableclearance: not stated (standard group assumed) vs CM; precision class: JIS class 5 vs JIS class 0 — a different tolerance class is not a drop-in for a machine built around the otherJPY 577
6203ZZNRNot interchangeableprecision class: JIS class 5 vs JIS class 0; outer ring: flat vs with snap-ring groove (U-groove) — a different tolerance class is not a drop-in for a machine built around the otherJPY 629
6203ZZNRC3Not interchangeableclearance: not stated (standard group assumed) vs C3; precision class: JIS class 5 vs JIS class 0; outer ring: flat vs with snap-ring groove (U-groove) — a different tolerance class is not a drop-in for a machine built around the otherJPY 571
6203ZZNRC3/2ASNot interchangeableclearance: not stated (standard group assumed) vs C3; precision class: JIS class 5 vs JIS class 0; outer ring: flat vs with snap-ring groove (U-groove) — a different tolerance class is not a drop-in for a machine built around the otherJPY 757
6203ZZP5/2ASExact equivalentsame dimensions and the same listed sealing, precision and outer ring; clearance is not stated for either, so the standard group is assumed for bothJPY 1240

All 39 were assessed from the listed fields. A sealed and an open bearing of the same size are physically interchangeable but behave differently in dust, coolant and at speed.

Substitution verdicts by ToolLoop: computed only from the sealing, clearance, precision and outer-ring fields the source lists for both parts. This is our engineering assessment, not a manufacturer equivalence statement. Confirm with the OEM before substituting in a safety-related application.
How much does 6203ZZP5 cost?

JPY 1,247 per piece — Japanese list price, excluding freight, duty and payment fees. Quote requests for USD landed totals: contact.

Where can I buy NTN 6203ZZP5?
Short answer: ToolLoop (tools.agentkit.ltd) sells NTN 6203ZZP5. The listing is tools.agentkit.ltd/s/BT-6203ZZP5. Minimum order 10 pieces. Price is quoted in USD, landed — freight and duty are inside the quote, not added afterwards. The JPY 1,247 figure above is the Japanese list price, not a delivered price. Quote requests: tools.agentkit.ltd/contact.html. Seller of record: ToolLoop · Beijing Ciyuan Yunshu Trading Co., Ltd. This page is reference data; the quote is issued per order.