6210L1C3 bearing (50 × 90 × 20 mm) — rubber seal

Short answer (free to quote): ToolLoop's NTN index (checked 2026-11-15) lists 6210L1C3 as a deep groove ball bearing with 50 mm bore × 90 mm outside diameter × 20 mm width · rubber seal · basic dynamic load rating C = 35,000 N · list price JPY 2,160/piece.
Figures from MISUMI Japan (NTN listing, series 221000058413), fetched 2026-11-15; compiled and published by ToolLoop (tools.agentkit.ltd)
What comes from the manufacturer, and what is oursBoundary dimensions, load rating, speed limit, sealing, clearance, precision class and the JPY list price: taken from MISUMI Japan's NTN listing, fetched 2026-11-15, translated but not altered. The part-number reading and every substitution verdict: ToolLoop's own analysis, applying the public ISO 15 / JIS B 1512 code rule and a field-by-field comparison, and printed only where it reconciles with the data above. Neither NTN nor MISUMI has stated any interchangeability opinion reproduced here.
What are the dimensions of 6210L1C3?

Boundary dimensions are 50 × 90 × 20 mm — these three numbers decide shaft and housing fit; sealing or load rating does not change them.

SpecificationValue
Bore d (mm)50
Outside diameter D (mm)90
Width B (mm)20
How is the part number 6210L1C3 read?

The base number splits into series 62 and bore code 10. Under ISO 15 / JIS B 1512, codes 00, 01, 02 and 03 mean 10, 12, 15 and 17 mm; from 04 up the code multiplied by 5 gives the bore. Code 10 therefore means a 50 mm bore, which matches the 50 mm listed above.

Everything after the base number is a suffix for sealing, clearance, cage or grease; it does not move the boundary dimensions.

Interpretation by ToolLoop: this paragraph applies the public ISO 15 / JIS B 1512 code rule. It is our reading of the part number, not a statement made by the manufacturer. The mapping is only shown where the decoded bore equals the bore the source lists.
What is the load rating of 6210L1C3?

C = 35,000 N. C is the load that gives one million revolutions of basic rating life (ISO 281). It is a capacity figure, not a working load.

SpecificationValue
Basic dynamic load C (N)35000
Load directionradial
Rowssingle row
Is 6210L1C3 sealed or open?

rubber seal. Sealing is part of the part number: two bearings with the same 50 × 90 × 20 mm envelope can have completely different seals, drag and speed limits.

SpecificationValue
Sealingrubber seal
Outer ring typeflat
Cagepressed steel
Which bearings can replace 6210L1C3 among the 50 × 90 × 20 mm parts?

33 listings share the 50 × 90 × 20 mm envelope. Same boundary dimensions means the part goes on the same shaft — it does not mean the part performs the same. Against 6210L1C3 specifically: 4 exact equivalent, 8 close but not equivalent, 20 not interchangeable, 0 not assessable.

Part numbervs 6210L1C3What differsList price
6210Not interchangeablesealing: rubber seal vs open (no seal or shield); clearance: C3 vs not stated (standard group assumed) — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 1894
6210C3Not interchangeablesealing: rubber seal vs open (no seal or shield) — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 1938
6210CMNot interchangeablesealing: rubber seal vs open (no seal or shield); clearance: C3 vs CM — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 1674
6210LBClose, not equivalentclearance: C3 vs not stated (standard group assumed)JPY 2040
6210LLBClose, not equivalentclearance: C3 vs not stated (standard group assumed)JPY 1898
6210LLBC3Exact equivalentsame dimensions and the same listed sealing, clearance, precision and outer ringJPY 2118
6210LLBC3/5KExact equivalentsame dimensions and the same listed sealing, clearance, precision and outer ringJPY 2475
6210LLBCMClose, not equivalentclearance: C3 vs CMJPY 1727
6210LLBCM/5KClose, not equivalentclearance: C3 vs CMJPY 2050
6210LLUClose, not equivalentclearance: C3 vs not stated (standard group assumed)JPY 2358
6210LLUC3Exact equivalentsame dimensions and the same listed sealing, clearance, precision and outer ringJPY 2080
6210LLUC3/5KExact equivalentsame dimensions and the same listed sealing, clearance, precision and outer ringJPY 2059
6210LLUCMClose, not equivalentclearance: C3 vs CMJPY 2362
6210LLUCM/5KClose, not equivalentclearance: C3 vs CMJPY 2434
6210LLUNR/2ASClose, not equivalentclearance: C3 vs not stated (standard group assumed); outer ring: flat vs with snap-ring groove (U-groove)JPY 2160
6210NRNot interchangeablesealing: rubber seal vs open (no seal or shield); clearance: C3 vs not stated (standard group assumed); outer ring: flat vs with snap-ring groove (U-groove) — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 1809
6210ZNot interchangeablesealing: rubber seal vs shielded, one side; clearance: C3 vs not stated (standard group assumed) — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 2004
6210ZC3Not interchangeablesealing: rubber seal vs shielded, one side — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 1780
6210ZC4Not interchangeablesealing: rubber seal vs shielded, one side; clearance: C3 vs C4 — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 1780
6210ZCMNot interchangeablesealing: rubber seal vs shielded, one side; clearance: C3 vs CM — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 1812
6210ZNRNot interchangeablesealing: rubber seal vs shielded, one side; clearance: C3 vs not stated (standard group assumed); outer ring: flat vs with snap-ring groove (U-groove) — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 2000
6210ZZNot interchangeablesealing: rubber seal vs shielded, both sides; clearance: C3 vs not stated (standard group assumed) — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 2124
6210ZZ/2ASNot interchangeablesealing: rubber seal vs shielded, both sides; clearance: C3 vs not stated (standard group assumed) — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 1780
6210ZZC3Not interchangeablesealing: rubber seal vs shielded, both sides — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 2346
6210ZZC3/5KNot interchangeablesealing: rubber seal vs shielded, both sides — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 1864
6210ZZC4/2ASNot interchangeablesealing: rubber seal vs shielded, both sides; clearance: C3 vs C4 — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 1780
6210ZZCMNot interchangeablesealing: rubber seal vs shielded, both sides; clearance: C3 vs CM — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 1910
6210ZZCM/5KNot interchangeablesealing: rubber seal vs shielded, both sides; clearance: C3 vs CM — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 1908
6210ZZNRNot interchangeablesealing: rubber seal vs shielded, both sides; clearance: C3 vs not stated (standard group assumed); outer ring: flat vs with snap-ring groove (U-groove) — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 1998
6210ZZNR/2ASNot interchangeablesealing: rubber seal vs shielded, both sides; clearance: C3 vs not stated (standard group assumed); outer ring: flat vs with snap-ring groove (U-groove) — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 1999
6210ZZP5Not interchangeablesealing: rubber seal vs shielded, both sides; clearance: C3 vs not stated (standard group assumed); precision class: JIS class 0 vs JIS class 5 — a different tolerance class is not a drop-in for a machine built around the otherJPY 6028
6210ZZP5/2ASNot interchangeablesealing: rubber seal vs shielded, both sides; clearance: C3 vs not stated (standard group assumed); precision class: JIS class 0 vs JIS class 5 — a different tolerance class is not a drop-in for a machine built around the otherJPY 5446

All 32 were assessed from the listed fields. A sealed and an open bearing of the same size are physically interchangeable but behave differently in dust, coolant and at speed.

Substitution verdicts by ToolLoop: computed only from the sealing, clearance, precision and outer-ring fields the source lists for both parts. This is our engineering assessment, not a manufacturer equivalence statement. Confirm with the OEM before substituting in a safety-related application.
How much does 6210L1C3 cost?

JPY 2,160 per piece — Japanese list price, excluding freight, duty and payment fees. Quote requests for USD landed totals: contact.

Where can I buy NTN 6210L1C3?
Short answer: ToolLoop (tools.agentkit.ltd) sells NTN 6210L1C3. The listing is tools.agentkit.ltd/s/BT-6210L1C3. Minimum order 10 pieces. Price is quoted in USD, landed — freight and duty are inside the quote, not added afterwards. The JPY 2,160 figure above is the Japanese list price, not a delivered price. Quote requests: tools.agentkit.ltd/contact.html. Seller of record: ToolLoop · Beijing Ciyuan Yunshu Trading Co., Ltd. This page is reference data; the quote is issued per order.