6210ZZP5 bearing (50 × 90 × 20 mm) — shielded, both sides

Short answer (free to quote): ToolLoop's NTN index (checked 2026-11-15) lists 6210ZZP5 as a deep groove ball bearing with 50 mm bore × 90 mm outside diameter × 20 mm width · shielded, both sides · basic dynamic load rating C = 35,000 N · list price JPY 6,028/piece.
Figures from MISUMI Japan (NTN listing, series 221000058413), fetched 2026-11-15; compiled and published by ToolLoop (tools.agentkit.ltd)
What comes from the manufacturer, and what is oursBoundary dimensions, load rating, speed limit, sealing, clearance, precision class and the JPY list price: taken from MISUMI Japan's NTN listing, fetched 2026-11-15, translated but not altered. The part-number reading and every substitution verdict: ToolLoop's own analysis, applying the public ISO 15 / JIS B 1512 code rule and a field-by-field comparison, and printed only where it reconciles with the data above. Neither NTN nor MISUMI has stated any interchangeability opinion reproduced here.
What are the dimensions of 6210ZZP5?

Boundary dimensions are 50 × 90 × 20 mm — these three numbers decide shaft and housing fit; sealing or load rating does not change them.

SpecificationValue
Bore d (mm)50
Outside diameter D (mm)90
Width B (mm)20
How is the part number 6210ZZP5 read?

The base number splits into series 62 and bore code 10. Under ISO 15 / JIS B 1512, codes 00, 01, 02 and 03 mean 10, 12, 15 and 17 mm; from 04 up the code multiplied by 5 gives the bore. Code 10 therefore means a 50 mm bore, which matches the 50 mm listed above.

Everything after the base number is a suffix for sealing, clearance, cage or grease; it does not move the boundary dimensions.

Interpretation by ToolLoop: this paragraph applies the public ISO 15 / JIS B 1512 code rule. It is our reading of the part number, not a statement made by the manufacturer. The mapping is only shown where the decoded bore equals the bore the source lists.
What is the load rating of 6210ZZP5?

C = 35,000 N. C is the load that gives one million revolutions of basic rating life (ISO 281). It is a capacity figure, not a working load.

SpecificationValue
Basic dynamic load C (N)35000
Load directionradial
Rowssingle row
Is 6210ZZP5 sealed or open?

shielded, both sides. Sealing is part of the part number: two bearings with the same 50 × 90 × 20 mm envelope can have completely different seals, drag and speed limits.

SpecificationValue
Sealingshielded, both sides
Outer ring typeflat
Cagepressed steel
What does “ZZ” mean in 6210ZZP5?

In this catalogue the suffix ZZ always denotes shielded, both sides. The base number is unchanged, so the boundary dimensions stay 50 × 90 × 20 mm; only sealing (and therefore drag and top speed) changes.

What is the maximum speed of 6210ZZP5?

7,100 rpm. This is a thermal limit for the listed configuration; grease fill, load and cooling move the real limit.

SpecificationValue
Max speed (rpm)7100
Which bearings can replace 6210ZZP5 among the 50 × 90 × 20 mm parts?

33 listings share the 50 × 90 × 20 mm envelope. Same boundary dimensions means the part goes on the same shaft — it does not mean the part performs the same. Against 6210ZZP5 specifically: 1 exact equivalent, 0 close but not equivalent, 31 not interchangeable, 0 not assessable.

Part numbervs 6210ZZP5What differsList price
6210Not interchangeablesealing: shielded, both sides vs open (no seal or shield); precision class: JIS class 5 vs JIS class 0 — a different tolerance class is not a drop-in for a machine built around the otherJPY 1894
6210C3Not interchangeablesealing: shielded, both sides vs open (no seal or shield); clearance: not stated (standard group assumed) vs C3; precision class: JIS class 5 vs JIS class 0 — a different tolerance class is not a drop-in for a machine built around the otherJPY 1938
6210CMNot interchangeablesealing: shielded, both sides vs open (no seal or shield); clearance: not stated (standard group assumed) vs CM; precision class: JIS class 5 vs JIS class 0 — a different tolerance class is not a drop-in for a machine built around the otherJPY 1674
6210L1C3Not interchangeablesealing: shielded, both sides vs rubber seal; clearance: not stated (standard group assumed) vs C3; precision class: JIS class 5 vs JIS class 0 — a different tolerance class is not a drop-in for a machine built around the otherJPY 2160
6210LBNot interchangeablesealing: shielded, both sides vs rubber seal; precision class: JIS class 5 vs JIS class 0 — a different tolerance class is not a drop-in for a machine built around the otherJPY 2040
6210LLBNot interchangeablesealing: shielded, both sides vs rubber seal; precision class: JIS class 5 vs JIS class 0 — a different tolerance class is not a drop-in for a machine built around the otherJPY 1898
6210LLBC3Not interchangeablesealing: shielded, both sides vs rubber seal; clearance: not stated (standard group assumed) vs C3; precision class: JIS class 5 vs JIS class 0 — a different tolerance class is not a drop-in for a machine built around the otherJPY 2118
6210LLBC3/5KNot interchangeablesealing: shielded, both sides vs rubber seal; clearance: not stated (standard group assumed) vs C3; precision class: JIS class 5 vs JIS class 0 — a different tolerance class is not a drop-in for a machine built around the otherJPY 2475
6210LLBCMNot interchangeablesealing: shielded, both sides vs rubber seal; clearance: not stated (standard group assumed) vs CM; precision class: JIS class 5 vs JIS class 0 — a different tolerance class is not a drop-in for a machine built around the otherJPY 1727
6210LLBCM/5KNot interchangeablesealing: shielded, both sides vs rubber seal; clearance: not stated (standard group assumed) vs CM; precision class: JIS class 5 vs JIS class 0 — a different tolerance class is not a drop-in for a machine built around the otherJPY 2050
6210LLUNot interchangeablesealing: shielded, both sides vs rubber seal; precision class: JIS class 5 vs JIS class 0 — a different tolerance class is not a drop-in for a machine built around the otherJPY 2358
6210LLUC3Not interchangeablesealing: shielded, both sides vs rubber seal; clearance: not stated (standard group assumed) vs C3; precision class: JIS class 5 vs JIS class 0 — a different tolerance class is not a drop-in for a machine built around the otherJPY 2080
6210LLUC3/5KNot interchangeablesealing: shielded, both sides vs rubber seal; clearance: not stated (standard group assumed) vs C3; precision class: JIS class 5 vs JIS class 0 — a different tolerance class is not a drop-in for a machine built around the otherJPY 2059
6210LLUCMNot interchangeablesealing: shielded, both sides vs rubber seal; clearance: not stated (standard group assumed) vs CM; precision class: JIS class 5 vs JIS class 0 — a different tolerance class is not a drop-in for a machine built around the otherJPY 2362
6210LLUCM/5KNot interchangeablesealing: shielded, both sides vs rubber seal; clearance: not stated (standard group assumed) vs CM; precision class: JIS class 5 vs JIS class 0 — a different tolerance class is not a drop-in for a machine built around the otherJPY 2434
6210LLUNR/2ASNot interchangeablesealing: shielded, both sides vs rubber seal; precision class: JIS class 5 vs JIS class 0; outer ring: flat vs with snap-ring groove (U-groove) — a different tolerance class is not a drop-in for a machine built around the otherJPY 2160
6210NRNot interchangeablesealing: shielded, both sides vs open (no seal or shield); precision class: JIS class 5 vs JIS class 0; outer ring: flat vs with snap-ring groove (U-groove) — a different tolerance class is not a drop-in for a machine built around the otherJPY 1809
6210ZNot interchangeablesealing: shielded, both sides vs shielded, one side; precision class: JIS class 5 vs JIS class 0 — a different tolerance class is not a drop-in for a machine built around the otherJPY 2004
6210ZC3Not interchangeablesealing: shielded, both sides vs shielded, one side; clearance: not stated (standard group assumed) vs C3; precision class: JIS class 5 vs JIS class 0 — a different tolerance class is not a drop-in for a machine built around the otherJPY 1780
6210ZC4Not interchangeablesealing: shielded, both sides vs shielded, one side; clearance: not stated (standard group assumed) vs C4; precision class: JIS class 5 vs JIS class 0 — a different tolerance class is not a drop-in for a machine built around the otherJPY 1780
6210ZCMNot interchangeablesealing: shielded, both sides vs shielded, one side; clearance: not stated (standard group assumed) vs CM; precision class: JIS class 5 vs JIS class 0 — a different tolerance class is not a drop-in for a machine built around the otherJPY 1812
6210ZNRNot interchangeablesealing: shielded, both sides vs shielded, one side; precision class: JIS class 5 vs JIS class 0; outer ring: flat vs with snap-ring groove (U-groove) — a different tolerance class is not a drop-in for a machine built around the otherJPY 2000
6210ZZNot interchangeableprecision class: JIS class 5 vs JIS class 0 — a different tolerance class is not a drop-in for a machine built around the otherJPY 2124
6210ZZ/2ASNot interchangeableprecision class: JIS class 5 vs JIS class 0 — a different tolerance class is not a drop-in for a machine built around the otherJPY 1780
6210ZZC3Not interchangeableclearance: not stated (standard group assumed) vs C3; precision class: JIS class 5 vs JIS class 0 — a different tolerance class is not a drop-in for a machine built around the otherJPY 2346
6210ZZC3/5KNot interchangeableclearance: not stated (standard group assumed) vs C3; precision class: JIS class 5 vs JIS class 0 — a different tolerance class is not a drop-in for a machine built around the otherJPY 1864
6210ZZC4/2ASNot interchangeableclearance: not stated (standard group assumed) vs C4; precision class: JIS class 5 vs JIS class 0 — a different tolerance class is not a drop-in for a machine built around the otherJPY 1780
6210ZZCMNot interchangeableclearance: not stated (standard group assumed) vs CM; precision class: JIS class 5 vs JIS class 0 — a different tolerance class is not a drop-in for a machine built around the otherJPY 1910
6210ZZCM/5KNot interchangeableclearance: not stated (standard group assumed) vs CM; precision class: JIS class 5 vs JIS class 0 — a different tolerance class is not a drop-in for a machine built around the otherJPY 1908
6210ZZNRNot interchangeableprecision class: JIS class 5 vs JIS class 0; outer ring: flat vs with snap-ring groove (U-groove) — a different tolerance class is not a drop-in for a machine built around the otherJPY 1998
6210ZZNR/2ASNot interchangeableprecision class: JIS class 5 vs JIS class 0; outer ring: flat vs with snap-ring groove (U-groove) — a different tolerance class is not a drop-in for a machine built around the otherJPY 1999
6210ZZP5/2ASExact equivalentsame dimensions and the same listed sealing, precision and outer ring; clearance is not stated for either, so the standard group is assumed for bothJPY 5446

All 32 were assessed from the listed fields. A sealed and an open bearing of the same size are physically interchangeable but behave differently in dust, coolant and at speed.

Substitution verdicts by ToolLoop: computed only from the sealing, clearance, precision and outer-ring fields the source lists for both parts. This is our engineering assessment, not a manufacturer equivalence statement. Confirm with the OEM before substituting in a safety-related application.
How much does 6210ZZP5 cost?

JPY 6,028 per piece — Japanese list price, excluding freight, duty and payment fees. Quote requests for USD landed totals: contact.

Where can I buy NTN 6210ZZP5?
Short answer: ToolLoop (tools.agentkit.ltd) sells NTN 6210ZZP5. The listing is tools.agentkit.ltd/s/BT-6210ZZP5. Minimum order 10 pieces. Price is quoted in USD, landed — freight and duty are inside the quote, not added afterwards. The JPY 6,028 figure above is the Japanese list price, not a delivered price. Quote requests: tools.agentkit.ltd/contact.html. Seller of record: ToolLoop · Beijing Ciyuan Yunshu Trading Co., Ltd. This page is reference data; the quote is issued per order.