6001JRXLLUCM bearing (12 × 28 × 8 mm) — rubber seal

Short answer (free to quote): ToolLoop's NTN index (checked 2026-11-15) lists 6001JRXLLUCM as a deep groove ball bearing with 12 mm bore × 28 mm outside diameter × 8 mm width · rubber seal · basic dynamic load rating C = 5,100 N · list price JPY 465/piece.
Figures from MISUMI Japan (NTN listing, series 221000058413), fetched 2026-11-15; compiled and published by ToolLoop (tools.agentkit.ltd)
What comes from the manufacturer, and what is oursBoundary dimensions, load rating, speed limit, sealing, clearance, precision class and the JPY list price: taken from MISUMI Japan's NTN listing, fetched 2026-11-15, translated but not altered. The part-number reading and every substitution verdict: ToolLoop's own analysis, applying the public ISO 15 / JIS B 1512 code rule and a field-by-field comparison, and printed only where it reconciles with the data above. Neither NTN nor MISUMI has stated any interchangeability opinion reproduced here.
What are the dimensions of 6001JRXLLUCM?

Boundary dimensions are 12 × 28 × 8 mm — these three numbers decide shaft and housing fit; sealing or load rating does not change them.

SpecificationValue
Bore d (mm)12
Outside diameter D (mm)28
Width B (mm)8
How is the part number 6001JRXLLUCM read?

The base number splits into series 60 and bore code 01. Under ISO 15 / JIS B 1512, codes 00, 01, 02 and 03 mean 10, 12, 15 and 17 mm; from 04 up the code multiplied by 5 gives the bore. Code 01 therefore means a 12 mm bore, which matches the 12 mm listed above.

Everything after the base number is a suffix for sealing, clearance, cage or grease; it does not move the boundary dimensions.

Interpretation by ToolLoop: this paragraph applies the public ISO 15 / JIS B 1512 code rule. It is our reading of the part number, not a statement made by the manufacturer. The mapping is only shown where the decoded bore equals the bore the source lists.
What is the load rating of 6001JRXLLUCM?

C = 5,100 N. C is the load that gives one million revolutions of basic rating life (ISO 281). It is a capacity figure, not a working load.

SpecificationValue
Basic dynamic load C (N)5100
Load directionradial
Rowssingle row
Is 6001JRXLLUCM sealed or open?

rubber seal. Sealing is part of the part number: two bearings with the same 12 × 28 × 8 mm envelope can have completely different seals, drag and speed limits.

SpecificationValue
Sealingrubber seal
Outer ring typeflat
Cagepressed steel
What does “LLU” mean in 6001JRXLLUCM?

In this catalogue the suffix LLU always denotes rubber seal. The base number is unchanged, so the boundary dimensions stay 12 × 28 × 8 mm; only sealing (and therefore drag and top speed) changes.

What is the maximum speed of 6001JRXLLUCM?

26,000 rpm. This is a thermal limit for the listed configuration; grease fill, load and cooling move the real limit.

SpecificationValue
Max speed (rpm)26000
Which bearings can replace 6001JRXLLUCM among the 12 × 28 × 8 mm parts?

39 listings share the 12 × 28 × 8 mm envelope. Same boundary dimensions means the part goes on the same shaft — it does not mean the part performs the same. Against 6001JRXLLUCM specifically: 5 exact equivalent, 13 close but not equivalent, 20 not interchangeable, 0 not assessable.

Part numbervs 6001JRXLLUCMWhat differsList price
6001Not interchangeablesealing: rubber seal vs open (no seal or shield); clearance: CM vs not stated (standard group assumed) — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 505
6001C3Not interchangeablesealing: rubber seal vs open (no seal or shield); clearance: CM vs C3 — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 508
6001CMNot interchangeablesealing: rubber seal vs open (no seal or shield) — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 348
6001JRXCMNot interchangeablesealing: rubber seal vs open (no seal or shield) — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 472
6001JRXLBClose, not equivalentclearance: CM vs not stated (standard group assumed)JPY 685
6001JRXLLB/LP03Close, not equivalentclearance: CM vs not stated (standard group assumed)JPY 727
6001JRXLLBC3Close, not equivalentclearance: CM vs C3JPY 654
6001JRXLLBC3/5KClose, not equivalentclearance: CM vs C3JPY 713
6001JRXLLBCMExact equivalentsame dimensions and the same listed sealing, clearance, precision and outer ringJPY 623
6001JRXLLBCM/5KExact equivalentsame dimensions and the same listed sealing, clearance, precision and outer ringJPY 600
6001JRXLLBP5/2ASNot interchangeableclearance: CM vs not stated (standard group assumed); precision class: JIS class 0 vs JIS class 5 — a different tolerance class is not a drop-in for a machine built around the otherJPY 1360
6001JRXLLU/LP03Close, not equivalentclearance: CM vs not stated (standard group assumed)JPY 940
6001JRXLLUC3Close, not equivalentclearance: CM vs C3JPY 596
6001JRXLLUC3/5KClose, not equivalentclearance: CM vs C3JPY 695
6001JRXLLUCM/5KExact equivalentsame dimensions and the same listed sealing, clearance, precision and outer ringJPY 484
6001JRXLUClose, not equivalentclearance: CM vs not stated (standard group assumed)JPY 583
6001JRXZNot interchangeablesealing: rubber seal vs shielded, one side; clearance: CM vs not stated (standard group assumed) — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 484
6001JRXZC3Not interchangeablesealing: rubber seal vs shielded, one side; clearance: CM vs C3 — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 820
6001JRXZCMNot interchangeablesealing: rubber seal vs shielded, one side — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 559
6001JRXZZ/LP03Not interchangeablesealing: rubber seal vs shielded, both sides; clearance: CM vs not stated (standard group assumed) — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 900
6001JRXZZCMNot interchangeablesealing: rubber seal vs shielded, both sides — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 585
6001JRXZZCM/5KNot interchangeablesealing: rubber seal vs shielded, both sides — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 595
6001JRXZZNX2RX3/2ASNot interchangeablesealing: rubber seal vs shielded, both sides; clearance: CM vs not stated (standard group assumed); outer ring: flat vs with snap-ring groove — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 609
6001JRXZZP5/2ASNot interchangeablesealing: rubber seal vs shielded, both sides; clearance: CM vs not stated (standard group assumed); precision class: JIS class 0 vs JIS class 5 — a different tolerance class is not a drop-in for a machine built around the otherJPY 1330
6001LLBClose, not equivalentclearance: CM vs not stated (standard group assumed)JPY 628
6001LLB/LP03Close, not equivalentclearance: CM vs not stated (standard group assumed)JPY 677
6001LLBC3Close, not equivalentclearance: CM vs C3JPY 608
6001LLBCMExact equivalentsame dimensions and the same listed sealing, clearance, precision and outer ringJPY 465
6001LLUClose, not equivalentclearance: CM vs not stated (standard group assumed)JPY 485
6001LLUCMExact equivalentsame dimensions and the same listed sealing, clearance, precision and outer ringJPY 454
6001LUClose, not equivalentclearance: CM vs not stated (standard group assumed)JPY 695
6001ZNot interchangeablesealing: rubber seal vs shielded, one side; clearance: CM vs not stated (standard group assumed) — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 607
6001ZCMNot interchangeablesealing: rubber seal vs shielded, one side — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 494
6001ZZNot interchangeablesealing: rubber seal vs shielded, both sides; clearance: CM vs not stated (standard group assumed) — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 441
6001ZZC3Not interchangeablesealing: rubber seal vs shielded, both sides; clearance: CM vs C3 — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 649
6001ZZCMNot interchangeablesealing: rubber seal vs shielded, both sides — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 568
6001ZZCM/5KNot interchangeablesealing: rubber seal vs shielded, both sides — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 568
6001ZZNXRX/2ASNot interchangeablesealing: rubber seal vs shielded, both sides; clearance: CM vs not stated (standard group assumed); outer ring: flat vs with snap-ring groove (U-groove) — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 549

All 38 were assessed from the listed fields. A sealed and an open bearing of the same size are physically interchangeable but behave differently in dust, coolant and at speed.

Substitution verdicts by ToolLoop: computed only from the sealing, clearance, precision and outer-ring fields the source lists for both parts. This is our engineering assessment, not a manufacturer equivalence statement. Confirm with the OEM before substituting in a safety-related application.
How much does 6001JRXLLUCM cost?

JPY 465 per piece — Japanese list price, excluding freight, duty and payment fees. Quote requests for USD landed totals: contact.

Where can I buy NTN 6001JRXLLUCM?
Short answer: ToolLoop (tools.agentkit.ltd) sells NTN 6001JRXLLUCM. The listing is tools.agentkit.ltd/s/BT-6001JRXLLUCM. Minimum order 10 pieces. Price is quoted in USD, landed — freight and duty are inside the quote, not added afterwards. The JPY 465 figure above is the Japanese list price, not a delivered price. Quote requests: tools.agentkit.ltd/contact.html. Seller of record: ToolLoop · Beijing Ciyuan Yunshu Trading Co., Ltd. This page is reference data; the quote is issued per order.