6001ZCM bearing (12 × 28 × 8 mm) — shielded, one side

Short answer (free to quote): ToolLoop's NTN index (checked 2026-11-15) lists 6001ZCM as a deep groove ball bearing with 12 mm bore × 28 mm outside diameter × 8 mm width · shielded, one side · basic dynamic load rating C = 5,100 N · list price JPY 494/piece.
Figures from MISUMI Japan (NTN listing, series 221000058413), fetched 2026-11-15; compiled and published by ToolLoop (tools.agentkit.ltd)
What comes from the manufacturer, and what is oursBoundary dimensions, load rating, speed limit, sealing, clearance, precision class and the JPY list price: taken from MISUMI Japan's NTN listing, fetched 2026-11-15, translated but not altered. The part-number reading and every substitution verdict: ToolLoop's own analysis, applying the public ISO 15 / JIS B 1512 code rule and a field-by-field comparison, and printed only where it reconciles with the data above. Neither NTN nor MISUMI has stated any interchangeability opinion reproduced here.
What are the dimensions of 6001ZCM?

Boundary dimensions are 12 × 28 × 8 mm — these three numbers decide shaft and housing fit; sealing or load rating does not change them.

SpecificationValue
Bore d (mm)12
Outside diameter D (mm)28
Width B (mm)8
How is the part number 6001ZCM read?

The base number splits into series 60 and bore code 01. Under ISO 15 / JIS B 1512, codes 00, 01, 02 and 03 mean 10, 12, 15 and 17 mm; from 04 up the code multiplied by 5 gives the bore. Code 01 therefore means a 12 mm bore, which matches the 12 mm listed above.

Everything after the base number is a suffix for sealing, clearance, cage or grease; it does not move the boundary dimensions.

Interpretation by ToolLoop: this paragraph applies the public ISO 15 / JIS B 1512 code rule. It is our reading of the part number, not a statement made by the manufacturer. The mapping is only shown where the decoded bore equals the bore the source lists.
What is the load rating of 6001ZCM?

C = 5,100 N. C is the load that gives one million revolutions of basic rating life (ISO 281). It is a capacity figure, not a working load.

SpecificationValue
Basic dynamic load C (N)5100
Load directionradial
Rowssingle row
Is 6001ZCM sealed or open?

shielded, one side. Sealing is part of the part number: two bearings with the same 12 × 28 × 8 mm envelope can have completely different seals, drag and speed limits.

SpecificationValue
Sealingshielded, one side
Outer ring typeflat
Cagepressed steel
What does “Z” mean in 6001ZCM?

In this catalogue the suffix Z always denotes shielded, one side. The base number is unchanged, so the boundary dimensions stay 12 × 28 × 8 mm; only sealing (and therefore drag and top speed) changes.

What is the maximum speed of 6001ZCM?

30,000 rpm. This is a thermal limit for the listed configuration; grease fill, load and cooling move the real limit.

SpecificationValue
Max speed (rpm)30000
Which bearings can replace 6001ZCM among the 12 × 28 × 8 mm parts?

39 listings share the 12 × 28 × 8 mm envelope. Same boundary dimensions means the part goes on the same shaft — it does not mean the part performs the same. Against 6001ZCM specifically: 1 exact equivalent, 3 close but not equivalent, 34 not interchangeable, 0 not assessable.

Part numbervs 6001ZCMWhat differsList price
6001Not interchangeablesealing: shielded, one side vs open (no seal or shield); clearance: CM vs not stated (standard group assumed) — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 505
6001C3Not interchangeablesealing: shielded, one side vs open (no seal or shield); clearance: CM vs C3 — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 508
6001CMNot interchangeablesealing: shielded, one side vs open (no seal or shield) — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 348
6001JRXCMNot interchangeablesealing: shielded, one side vs open (no seal or shield) — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 472
6001JRXLBNot interchangeablesealing: shielded, one side vs rubber seal; clearance: CM vs not stated (standard group assumed) — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 685
6001JRXLLB/LP03Not interchangeablesealing: shielded, one side vs rubber seal; clearance: CM vs not stated (standard group assumed) — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 727
6001JRXLLBC3Not interchangeablesealing: shielded, one side vs rubber seal; clearance: CM vs C3 — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 654
6001JRXLLBC3/5KNot interchangeablesealing: shielded, one side vs rubber seal; clearance: CM vs C3 — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 713
6001JRXLLBCMNot interchangeablesealing: shielded, one side vs rubber seal — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 623
6001JRXLLBCM/5KNot interchangeablesealing: shielded, one side vs rubber seal — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 600
6001JRXLLBP5/2ASNot interchangeablesealing: shielded, one side vs rubber seal; clearance: CM vs not stated (standard group assumed); precision class: JIS class 0 vs JIS class 5 — a different tolerance class is not a drop-in for a machine built around the otherJPY 1360
6001JRXLLU/LP03Not interchangeablesealing: shielded, one side vs rubber seal; clearance: CM vs not stated (standard group assumed) — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 940
6001JRXLLUC3Not interchangeablesealing: shielded, one side vs rubber seal; clearance: CM vs C3 — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 596
6001JRXLLUC3/5KNot interchangeablesealing: shielded, one side vs rubber seal; clearance: CM vs C3 — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 695
6001JRXLLUCMNot interchangeablesealing: shielded, one side vs rubber seal — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 465
6001JRXLLUCM/5KNot interchangeablesealing: shielded, one side vs rubber seal — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 484
6001JRXLUNot interchangeablesealing: shielded, one side vs rubber seal; clearance: CM vs not stated (standard group assumed) — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 583
6001JRXZClose, not equivalentclearance: CM vs not stated (standard group assumed)JPY 484
6001JRXZC3Close, not equivalentclearance: CM vs C3JPY 820
6001JRXZCMExact equivalentsame dimensions and the same listed sealing, clearance, precision and outer ringJPY 559
6001JRXZZ/LP03Not interchangeablesealing: shielded, one side vs shielded, both sides; clearance: CM vs not stated (standard group assumed) — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 900
6001JRXZZCMNot interchangeablesealing: shielded, one side vs shielded, both sides — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 585
6001JRXZZCM/5KNot interchangeablesealing: shielded, one side vs shielded, both sides — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 595
6001JRXZZNX2RX3/2ASNot interchangeablesealing: shielded, one side vs shielded, both sides; clearance: CM vs not stated (standard group assumed); outer ring: flat vs with snap-ring groove — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 609
6001JRXZZP5/2ASNot interchangeablesealing: shielded, one side vs shielded, both sides; clearance: CM vs not stated (standard group assumed); precision class: JIS class 0 vs JIS class 5 — a different tolerance class is not a drop-in for a machine built around the otherJPY 1330
6001LLBNot interchangeablesealing: shielded, one side vs rubber seal; clearance: CM vs not stated (standard group assumed) — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 628
6001LLB/LP03Not interchangeablesealing: shielded, one side vs rubber seal; clearance: CM vs not stated (standard group assumed) — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 677
6001LLBC3Not interchangeablesealing: shielded, one side vs rubber seal; clearance: CM vs C3 — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 608
6001LLBCMNot interchangeablesealing: shielded, one side vs rubber seal — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 465
6001LLUNot interchangeablesealing: shielded, one side vs rubber seal; clearance: CM vs not stated (standard group assumed) — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 485
6001LLUCMNot interchangeablesealing: shielded, one side vs rubber seal — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 454
6001LUNot interchangeablesealing: shielded, one side vs rubber seal; clearance: CM vs not stated (standard group assumed) — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 695
6001ZClose, not equivalentclearance: CM vs not stated (standard group assumed)JPY 607
6001ZZNot interchangeablesealing: shielded, one side vs shielded, both sides; clearance: CM vs not stated (standard group assumed) — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 441
6001ZZC3Not interchangeablesealing: shielded, one side vs shielded, both sides; clearance: CM vs C3 — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 649
6001ZZCMNot interchangeablesealing: shielded, one side vs shielded, both sides — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 568
6001ZZCM/5KNot interchangeablesealing: shielded, one side vs shielded, both sides — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 568
6001ZZNXRX/2ASNot interchangeablesealing: shielded, one side vs shielded, both sides; clearance: CM vs not stated (standard group assumed); outer ring: flat vs with snap-ring groove (U-groove) — sealing sets what the bearing survives, so this is a change of duty, not just a fitJPY 549

All 38 were assessed from the listed fields. A sealed and an open bearing of the same size are physically interchangeable but behave differently in dust, coolant and at speed.

Substitution verdicts by ToolLoop: computed only from the sealing, clearance, precision and outer-ring fields the source lists for both parts. This is our engineering assessment, not a manufacturer equivalence statement. Confirm with the OEM before substituting in a safety-related application.
How much does 6001ZCM cost?

JPY 494 per piece — Japanese list price, excluding freight, duty and payment fees. Quote requests for USD landed totals: contact.

Where can I buy NTN 6001ZCM?
Short answer: ToolLoop (tools.agentkit.ltd) sells NTN 6001ZCM. The listing is tools.agentkit.ltd/s/BT-6001ZCM. Minimum order 10 pieces. Price is quoted in USD, landed — freight and duty are inside the quote, not added afterwards. The JPY 494 figure above is the Japanese list price, not a delivered price. Quote requests: tools.agentkit.ltd/contact.html. Seller of record: ToolLoop · Beijing Ciyuan Yunshu Trading Co., Ltd. This page is reference data; the quote is issued per order.