10 × 22 × 6 mm bearing: NTN and NSK part numbers and JPY prices

Short answer (free to quote): For a 10 mm bore × 22 mm outside diameter × 6 mm width deep groove ball bearing, ToolLoop's index holds 37 listings across NTN and NSK. In the open variant the cheapest listing is NSK at ¥571 against NTN at ¥697 — a 18.1% difference (MISUMI Japan list prices, fetched 2026-11-15).
Prices and dimensions from MISUMI Japan, fetched 2026-11-15; comparison by ToolLoop
What is the distributor's, what is oursBoundary dimensions, sealing, load ratings, the static rating where the listing gives one, and the JPY list price: taken from the MISUMI Japan listing for each brand, translated but not altered. The cheapest-in-variant pick, the percentage gap and every remark about which listing is worth looking at: ToolLoop's calculation. Neither NTN nor NSK has stated an interchangeability opinion that is reproduced here.

Every listing in this size

BrandPart numberSealingC (N)C0 (N)List price (JPY)Source
NSK6900VVC3rubber seal27001270536source
NSK6900open (no seal or shield)27001270571source
NSK6900Z1shielded, one side27001270572source
NSK6900CMopen (no seal or shield)27001270584source
NSK6900Zshielded, one side27001270586source
NSK6900ZZC3shielded, both sides27001270595source
NSK6900ZZshielded, both sides27001270603source
NSK6900-H-20T1XDD1rubber seal27001270639source
NSK6900DDrubber seal27001270678source
NSK6900DDUrubber seal27001270678source
NSK6900ZZNXRshielded, both sides27001270736source
NSK6900-H-20T1XZZ1shielded, both sides27001270743source
NSK6900VVrubber seal27001270745source
NSK6900-H-20T1XDDrubber seal27001270932source
NSK6900L11-H-20DD1rubber seal270012703099source
NTN6900ZZC3shielded, both sides2700—549source
NTN6900LLBrubber seal2700—569source
NTN6900ZZ/5Kshielded, both sides2700—588source
NTN6900ZZC3/5Kshielded, both sides2700—618source
NTN6900LLB/2ASrubber seal2700—631source
NTN6900Zshielded, one side2700—646source
NTN6900ZZshielded, both sides2700—646source
NTN6900LLUrubber seal2700—667source
NTN6900LLU/2ASrubber seal2700—695source
NTN6900open (no seal or shield)2700—697source
NTN6900LLBC3/5Krubber seal2700—728source
NTN6900LLBCM/5Krubber seal2700—728source
NTN6900ZZNRshielded, both sides2700—749source
NTN6900LLUNR/2ASrubber seal2700—757source
NTN6900LLBC3rubber seal2700—788source
NTN6900ZZ/LP03shielded, both sides2700—790source
NTN6900ZZNR/2ASshielded, both sides2700—810source
NTN6900NRopen (no seal or shield)2700—835source
NTN6900LLU/LP03rubber seal2700—840source
NTN6900LLUNRrubber seal2700—882source
NTN6900LLUC3/5Krubber seal2700—990source
NTN6900ZZP5/2ASshielded, both sides2700—1690source
Written by ToolLoop: same boundary dimensions means the two brands drop into the same seat. It does not mean the same load rating, the same speed ceiling or the same internal clearance — compare the C and C0 columns above before treating them as equals.

The seat this bearing needs

A 10 mm bore falls in the ISO 286 band 6–10 mm, where IT7 is 15 µm wide. If the shaft seat is machined to h6, the shaft measures 9.991 to 10.000 mm; a H7/h6 pair at this nominal gives 0 to +24 µm.

Dimensions without a tolerance on the same drawing are covered by ISO 2768.