12 × 24 × 6 mm bearing: NTN and NSK part numbers and JPY prices

Short answer (free to quote): For a 12 mm bore × 24 mm outside diameter × 6 mm width deep groove ball bearing, ToolLoop's index holds 35 listings across NTN and NSK. In the open variant the cheapest listing is NTN at ¥536 against NSK at ¥596 — a 11.2% difference (MISUMI Japan list prices, fetched 2026-11-15).
Prices and dimensions from MISUMI Japan, fetched 2026-11-15; comparison by ToolLoop
What is the distributor's, what is oursBoundary dimensions, sealing, load ratings, the static rating where the listing gives one, and the JPY list price: taken from the MISUMI Japan listing for each brand, translated but not altered. The cheapest-in-variant pick, the percentage gap and every remark about which listing is worth looking at: ToolLoop's calculation. Neither NTN nor NSK has stated an interchangeability opinion that is reproduced here.

Every listing in this size

BrandPart numberSealingC (N)C0 (N)List price (JPY)Source
NSK6901open (no seal or shield)28901460596source
NSK6901DDUrubber seal28901460603source
NSK6901ZZshielded, both sides28901460629source
NSK6901DDrubber seal28901460655source
NSK6901DDC3rubber seal28901460664source
NSK6901ZZNRshielded, both sides28901460670source
NSK6901VVC3rubber seal28901460676source
NSK6901Z2shielded, one side28901460701source
NSK6901VVrubber seal28901460715source
NSK6901-H-20T1XZZ2shielded, both sides28901460790source
NSK6901U-H-20T1Xopen (no seal or shield)28901460858source
NSK6901-H-20T1XDD1rubber seal28901460895source
NSK6901-H-20T1XDDrubber seal28901460907source
NSK6901-H-ZZU76UG9shielded, both sides289014601670source
NSK6901L11DD1rubber seal289014602260source
NSK6901L11DDrubber seal289014603015source
NSK6901L11-H-20DD1rubber seal289014604201source
NTN6901open (no seal or shield)2890—536source
NTN6901LLUrubber seal2890—579source
NTN6901Zshielded, one side2890—631source
NTN6901C3open (no seal or shield)2890—636source
NTN6901ZZshielded, both sides2890—648source
NTN6901LLBrubber seal2890—659source
NTN6901ZZNRshielded, both sides2890—781source
NTN6901LLB/2ASrubber seal2890—829source
NTN6901NRopen (no seal or shield)2890—831source
NTN6901ZZC3shielded, both sides2890—870source
NTN6901LLU/2ASrubber seal2890—883source
NTN6901ZZNR/2ASshielded, both sides2890—926source
NTN6901ZZC3/5Kshielded, both sides2890—960source
NTN6901LLBC3/5Krubber seal2890—1000source
NTN6901LUrubber seal2890—1000source
NTN6901LLUNR/2ASrubber seal2890—1070source
NTN6901ZZ/LP03shielded, both sides2890—1070source
NTN6901LLB/LP03rubber seal2890—1140source
Written by ToolLoop: same boundary dimensions means the two brands drop into the same seat. It does not mean the same load rating, the same speed ceiling or the same internal clearance — compare the C and C0 columns above before treating them as equals.

The seat this bearing needs

A 12 mm bore falls in the ISO 286 band 10–18 mm, where IT7 is 18 µm wide. If the shaft seat is machined to h6, the shaft measures 11.989 to 12.000 mm; a H7/h6 pair at this nominal gives 0 to +29 µm.

Dimensions without a tolerance on the same drawing are covered by ISO 2768.