ISO 286 tolerances for 10–18 mm: IT grades and fit limits

Short answer (free to quote): In the 10–18 mm band of ISO 286-1, IT7 is 18 µm wide and IT6 is 11 µm, so an H7/h6 pair at a nominal 14 mm can move between 0 and +29 µm (calculated by ToolLoop, checked 2026-11-15). There are 625 deep groove ball bearing listings in ToolLoop's index with a bore in this band.
ISO 286-1:2010 tables; counts from the MISUMI Japan listing, fetched 2026-11-15
What is standard text, what is our arithmeticThe tolerance and deviation values are the tabulated values of ISO 286-1:2010 / ISO 2768-1:1989, taken from three independently published open datasets and compared cell by cell; only cells where all datasets that carry them agree are shown. The standard documents themselves are not reproduced. The limit sizes in millimetres, the clearance/interference ranges and every sentence about which fit is used for what are calculated or written by ToolLoop — they are not quoted from the standard.

Tolerance widths in this band

GradeWidth (µm)H hole EI/ES (µm)h shaft ei/es (µm)
IT580 / +8+8 / 0
IT6110 / +11+11 / 0
IT7180 / +18+18 / 0
IT8270 / +27+27 / 0
IT9430 / +43+43 / 0
IT10700 / +70+70 / 0
IT111100 / +110+110 / 0

Fits in this band

FitHole EI/ESShaft ei/esClearance (µm)
H7/h60 / +18-11 / 00 … +29
H7/g60 / +18-17 / -6+6 … +35
H7/f70 / +18-34 / -16+16 … +52
H7/e80 / +18-59 / -32+32 … +77
H7/d90 / +18-93 / -50+50 … +111
H7/js60 / +18-5.5 / +5.5-5.5 … +23.5
H7/k60 / +18+1 / +12-12 … +17
H7/m60 / +18+7 / +18-18 … +11
H7/n60 / +18+12 / +23-23 … +6
H7/p60 / +18+18 / +29-29 … 0
H7/r60 / +18+23 / +34-34 … -5
H7/s60 / +18+28 / +39-39 … -10
H8/f70 / +27-34 / -16+16 … +61
H8/h70 / +27-18 / 00 … +45
H9/d90 / +43-93 / -50+50 … +136
H11/c110 / +110-205 / -95+95 … +315
Provenance: primary table ottonic/standards-mcp-server (src/domain/iso286.ts, MIT); cross-checked against clay-good/anvilate (tolerance/data/iso286_*.yaml, MIT) and chenzefeng09/iso-286-fits (fits.json, MIT). 393 overlapping cells compared, 0 disagreements, checked 2026-11-15.

Deep groove ball bearings with a bore in this band

625 listings; first 40 by bore.

Part numberBrandd × D × B (mm)SealingList price (JPY)
16001NTN12 × 28 × 7open (no seal or shield)664
16001JRXNTN12 × 28 × 7open (no seal or shield)649
6001NTN12 × 28 × 8open (no seal or shield)505
6001C3NTN12 × 28 × 8open (no seal or shield)508
6001CMNTN12 × 28 × 8open (no seal or shield)348
6001JRXCMNTN12 × 28 × 8open (no seal or shield)472
6001JRXLBNTN12 × 28 × 8rubber seal685
6001JRXLLB/LP03NTN12 × 28 × 8rubber seal727
6001JRXLLBC3NTN12 × 28 × 8rubber seal654
6001JRXLLBC3/5KNTN12 × 28 × 8rubber seal713
6001JRXLLBCMNTN12 × 28 × 8rubber seal623
6001JRXLLBCM/5KNTN12 × 28 × 8rubber seal600
6001JRXLLBP5/2ASNTN12 × 28 × 8rubber seal1360
6001JRXLLU/LP03NTN12 × 28 × 8rubber seal940
6001JRXLLUC3NTN12 × 28 × 8rubber seal596
6001JRXLLUC3/5KNTN12 × 28 × 8rubber seal695
6001JRXLLUCMNTN12 × 28 × 8rubber seal465
6001JRXLLUCM/5KNTN12 × 28 × 8rubber seal484
6001JRXLUNTN12 × 28 × 8rubber seal583
6001JRXZNTN12 × 28 × 8shielded, one side484
6001JRXZC3NTN12 × 28 × 8shielded, one side820
6001JRXZCMNTN12 × 28 × 8shielded, one side559
6001JRXZZ/LP03NTN12 × 28 × 8shielded, both sides900
6001JRXZZCMNTN12 × 28 × 8shielded, both sides585
6001JRXZZCM/5KNTN12 × 28 × 8shielded, both sides595
6001JRXZZNX2RX3/2ASNTN12 × 28 × 8shielded, both sides609
6001JRXZZP5/2ASNTN12 × 28 × 8shielded, both sides1330
6001LLBNTN12 × 28 × 8rubber seal628
6001LLB/LP03NTN12 × 28 × 8rubber seal677
6001LLBC3NTN12 × 28 × 8rubber seal608
6001LLBCMNTN12 × 28 × 8rubber seal465
6001LLUNTN12 × 28 × 8rubber seal485
6001LLUCMNTN12 × 28 × 8rubber seal454
6001LUNTN12 × 28 × 8rubber seal695
6001ZNTN12 × 28 × 8shielded, one side607
6001ZCMNTN12 × 28 × 8shielded, one side494
6001ZZNTN12 × 28 × 8shielded, both sides441
6001ZZC3NTN12 × 28 × 8shielded, both sides649
6001ZZCMNTN12 × 28 × 8shielded, both sides568
6001ZZCM/5KNTN12 × 28 × 8shielded, both sides568