17 × 30 × 7 mm bearing: NTN and NSK part numbers and JPY prices

Short answer (free to quote): For a 17 mm bore × 30 mm outside diameter × 7 mm width deep groove ball bearing, ToolLoop's index holds 32 listings across NTN and NSK. In the sealed variant the cheapest listing is NSK at ¥611 against NTN at ¥705 — a 13.3% difference (MISUMI Japan list prices, fetched 2026-11-15).
Prices and dimensions from MISUMI Japan, fetched 2026-11-15; comparison by ToolLoop
What is the distributor's, what is oursBoundary dimensions, sealing, load ratings, the static rating where the listing gives one, and the JPY list price: taken from the MISUMI Japan listing for each brand, translated but not altered. The cheapest-in-variant pick, the percentage gap and every remark about which listing is worth looking at: ToolLoop's calculation. Neither NTN nor NSK has stated an interchangeability opinion that is reproduced here.

Every listing in this size

BrandPart numberSealingC (N)C0 (N)List price (JPY)Source
NSK6903VVC3rubber seal46002550611source
NSK6903open (no seal or shield)46002550675source
NSK6903Zshielded, one side46002550679source
NSK6903DDUrubber seal46002550720source
NSK6903ZZshielded, both sides46002550738source
NSK6903CMopen (no seal or shield)46002550787source
NSK6903VVrubber seal46002550796source
NSK6903-H-20T1XDDU1rubber seal460025501078source
NTN6903open (no seal or shield)4650—614source
NTN6903ZZC3shielded, both sides4650—688source
NTN6903LLU/2ASrubber seal4650—705source
NTN6903Zshielded, one side4650—711source
NTN6903ZZshielded, both sides4650—730source
NTN6903JRXLLU/2ASrubber seal4650—777source
NTN6903JRXLLBrubber seal4650—797source
NTN6903JRXLLB/2ASrubber seal4650—798source
NTN6903LLB/5Krubber seal4650—804source
NTN6903JRXopen (no seal or shield)4650—816source
NTN6903JRXZZNR/2ASshielded, both sides4650—821source
NTN6903LLB/2ASrubber seal4650—824source
NTN6903ZZ/5Kshielded, both sides4650—826source
NTN6903LLBrubber seal4650—834source
NTN6903JRXLLUrubber seal4650—837source
NTN6903ZZNRshielded, both sides4650—846source
NTN6903JRXLLB/5Krubber seal4650—852source
NTN6903JRXZZCM/5Kshielded, both sides4650—853source
NTN6903JRXZZ/5Kshielded, both sides4650—854source
NTN6903LLUrubber seal4650—869source
NTN6903JRXZshielded, one side4650—879source
NTN6903JRXZZ/LP03shielded, both sides4650—1140source
NTN6903JRXLLUNR/2ASrubber seal4650—1150source
NTN6903JRXLLU/LP03rubber seal4650—1220source
Written by ToolLoop: same boundary dimensions means the two brands drop into the same seat. It does not mean the same load rating, the same speed ceiling or the same internal clearance — compare the C and C0 columns above before treating them as equals.

The seat this bearing needs

A 17 mm bore falls in the ISO 286 band 10–18 mm, where IT7 is 18 µm wide. If the shaft seat is machined to h6, the shaft measures 16.989 to 17.000 mm; a H7/h6 pair at this nominal gives 0 to +29 µm.

Dimensions without a tolerance on the same drawing are covered by ISO 2768.