20 × 47 × 14 mm bearing: NTN and NSK part numbers and JPY prices

Short answer (free to quote): For a 20 mm bore × 47 mm outside diameter × 14 mm width deep groove ball bearing, ToolLoop's index holds 57 listings across NTN and NSK. In the open variant the cheapest listing is NSK at ¥424 against NTN at ¥666 — a 36.3% difference (MISUMI Japan list prices, fetched 2026-11-15).
Prices and dimensions from MISUMI Japan, fetched 2026-11-15; comparison by ToolLoop
What is the distributor's, what is oursBoundary dimensions, sealing, load ratings, the static rating where the listing gives one, and the JPY list price: taken from the MISUMI Japan listing for each brand, translated but not altered. The cheapest-in-variant pick, the percentage gap and every remark about which listing is worth looking at: ToolLoop's calculation. Neither NTN nor NSK has stated an interchangeability opinion that is reproduced here.

Every listing in this size

BrandPart numberSealingC (N)C0 (N)List price (JPY)Source
NSK6204NRopen (no seal or shield)128006600424source
NSK6204ZZshielded, both sides128006600498source
NSK6204ZZC3shielded, both sides128006600517source
NSK6204open (no seal or shield)128006600529source
NSK6204DDUC3E NS7S1rubber seal128006600566source
NSK6204DDUrubber seal128006600572source
NSK6204VVrubber seal128006600572source
NSK6204ZZNRshielded, both sides128006600579source
NSK6204VVC3rubber seal128006600585source
NSK6204Zshielded, one side128006600609source
NSK6204VVNRrubber seal1280066001439source
NSK6204L11DDUrubber seal1280066001508source
NSK6204-H-20T1XAZZshielded, both sides1280066001526source
NSK6204U-H-20T1XAopen (no seal or shield)1280066001541source
NSK6204P5open (no seal or shield)1280066001984source
NSK6204-H-ZZU76UG27shielded, both sides1280066003364source
NTN6204ZZCMshielded, both sides12800—532source
NTN6204LLUCM/5Krubber seal12800—538source
NTN6204ZZCM/5Kshielded, both sides12800—541source
NTN6204ZCMshielded, one side12800—545source
NTN6204LLUC3/5Krubber seal12800—610source
NTN6204open (no seal or shield)12800—666source
NTN6204LLUrubber seal12800—672source
NTN6204LLBC3rubber seal12800—677source
NTN6204C3open (no seal or shield)12800—678source
NTN6204CMopen (no seal or shield)12800—679source
NTN6204LLBrubber seal12800—686source
NTN6204ZZC3/5Kshielded, both sides12800—690source
NTN6204ZZNRshielded, both sides12800—701source
NTN6204LLUNR/2ASrubber seal12800—722source
NTN6204ZC3shielded, one side12800—730source
NTN6204ZZshielded, both sides12800—732source
NTN6204Zshielded, one side12800—733source
NTN6204ZNRshielded, one side12800—733source
NTN6204LLBCMrubber seal12800—737source
NTN6204ZZC3shielded, both sides12800—743source
NTN6204LLUNRrubber seal12800—744source
NTN6204LLUC3rubber seal12800—769source
NTN6204ZZ/LP03shielded, both sides12800—794source
NTN6204LBrubber seal12800—798source
NTN6204LLUCMrubber seal12800—799source
NTN6204ZZNR/2ASshielded, both sides12800—809source
NTN6204LLBCM/5Krubber seal12800—818source
NTN6204ZC4shielded, one side12800—900source
NTN6204ZZC3/L448shielded, both sides12800—900source
NTN6204ZZC4/5Kshielded, both sides12800—900source
NTN6204LUrubber seal12800—915source
NTN6204LLU/2ASrubber seal12800—940source
NTN6204LLBNR/2ASrubber seal12800—1000source
NTN6204LLBC3/5Krubber seal12800—1004source
NTN6204LLB/LP03rubber seal12800—1050source
NTN6204LLU/LP03rubber seal12800—1050source
NTN6204C3P6open (no seal or shield)12800—1060source
NTN6204C3P5open (no seal or shield)12800—1346source
NTN6204ZZP5shielded, both sides12800—1548source
NTN6204LLBP5/2ASrubber seal12800—1610source
NTN6204ZZP5/2ASshielded, both sides12800—2129source
Written by ToolLoop: same boundary dimensions means the two brands drop into the same seat. It does not mean the same load rating, the same speed ceiling or the same internal clearance — compare the C and C0 columns above before treating them as equals.

The seat this bearing needs

A 20 mm bore falls in the ISO 286 band 18–30 mm, where IT7 is 21 µm wide. If the shaft seat is machined to h6, the shaft measures 19.987 to 20.000 mm; a H7/h6 pair at this nominal gives 0 to +34 µm.

Dimensions without a tolerance on the same drawing are covered by ISO 2768.