ISO 286 tolerances for 18–30 mm: IT grades and fit limits

Short answer (free to quote): In the 18–30 mm band of ISO 286-1, IT7 is 21 µm wide and IT6 is 13 µm, so an H7/h6 pair at a nominal 24 mm can move between 0 and +34 µm (calculated by ToolLoop, checked 2026-11-15). There are 739 deep groove ball bearing listings in ToolLoop's index with a bore in this band.
ISO 286-1:2010 tables; counts from the MISUMI Japan listing, fetched 2026-11-15
What is standard text, what is our arithmeticThe tolerance and deviation values are the tabulated values of ISO 286-1:2010 / ISO 2768-1:1989, taken from three independently published open datasets and compared cell by cell; only cells where all datasets that carry them agree are shown. The standard documents themselves are not reproduced. The limit sizes in millimetres, the clearance/interference ranges and every sentence about which fit is used for what are calculated or written by ToolLoop — they are not quoted from the standard.

Tolerance widths in this band

GradeWidth (µm)H hole EI/ES (µm)h shaft ei/es (µm)
IT590 / +9+9 / 0
IT6130 / +13+13 / 0
IT7210 / +21+21 / 0
IT8330 / +33+33 / 0
IT9520 / +52+52 / 0
IT10840 / +84+84 / 0
IT111300 / +130+130 / 0

Fits in this band

FitHole EI/ESShaft ei/esClearance (µm)
H7/h60 / +21-13 / 00 … +34
H7/g60 / +21-20 / -7+7 … +41
H7/f70 / +21-41 / -20+20 … +62
H7/e80 / +21-73 / -40+40 … +94
H7/d90 / +21-117 / -65+65 … +138
H7/js60 / +21-6.5 / +6.5-6.5 … +27.5
H7/k60 / +21+2 / +15-15 … +19
H7/m60 / +21+8 / +21-21 … +13
H7/n60 / +21+15 / +28-28 … +6
H7/p60 / +21+22 / +35-35 … -1
H7/r60 / +21+28 / +41-41 … -7
H7/s60 / +21+35 / +48-48 … -14
H8/f70 / +33-41 / -20+20 … +74
H8/h70 / +33-21 / 00 … +54
H9/d90 / +52-117 / -65+65 … +169
H11/c110 / +130-240 / -110+110 … +370
Provenance: primary table ottonic/standards-mcp-server (src/domain/iso286.ts, MIT); cross-checked against clay-good/anvilate (tolerance/data/iso286_*.yaml, MIT) and chenzefeng09/iso-286-fits (fits.json, MIT). 393 overlapping cells compared, 0 disagreements, checked 2026-11-15.

Deep groove ball bearings with a bore in this band

739 listings; first 40 by bore.

Part numberBrandd × D × B (mm)SealingList price (JPY)
EN19NSK19 × 40 × 9open (no seal or shield)2015
16004NTN20 × 42 × 8open (no seal or shield)576
6004NTN20 × 42 × 12open (no seal or shield)624
6004C3NTN20 × 42 × 12open (no seal or shield)648
6004CMNTN20 × 42 × 12open (no seal or shield)450
6004LBNTN20 × 42 × 12rubber seal764
6004LLBNTN20 × 42 × 12rubber seal604
6004LLB/LP03NTN20 × 42 × 12rubber seal768
6004LLBC3NTN20 × 42 × 12rubber seal792
6004LLBC3/5KNTN20 × 42 × 12rubber seal876
6004LLBCMNTN20 × 42 × 12rubber seal701
6004LLBCM/5KNTN20 × 42 × 12rubber seal603
6004LLBNRNTN20 × 42 × 12rubber seal716
6004LLBNR/2ASNTN20 × 42 × 12rubber seal715
6004LLUNTN20 × 42 × 12rubber seal665
6004LLUC3NTN20 × 42 × 12rubber seal631
6004LLUC3/5KNTN20 × 42 × 12rubber seal835
6004LLUCMNTN20 × 42 × 12rubber seal784
6004LLUCM/5KNTN20 × 42 × 12rubber seal550
6004LLUNRNTN20 × 42 × 12rubber seal688
6004LLUNR/2ASNTN20 × 42 × 12rubber seal672
6004LUNTN20 × 42 × 12rubber seal581
6004NRNTN20 × 42 × 12open (no seal or shield)817
6004P4NTN20 × 42 × 12open (no seal or shield)1910
6004P5NTN20 × 42 × 12open (no seal or shield)1296
6004ZNTN20 × 42 × 12shielded, one side533
6004ZC3NTN20 × 42 × 12shielded, one side532
6004ZCMNTN20 × 42 × 12shielded, one side409
6004ZNRNTN20 × 42 × 12shielded, one side930
6004ZZNTN20 × 42 × 12shielded, both sides487
6004ZZ/LP03NTN20 × 42 × 12shielded, both sides608
6004ZZC3NTN20 × 42 × 12shielded, both sides767
6004ZZC3/5KNTN20 × 42 × 12shielded, both sides821
6004ZZC4/5KNTN20 × 42 × 12shielded, both sides870
6004ZZCMNTN20 × 42 × 12shielded, both sides424
6004ZZCM/5KNTN20 × 42 × 12shielded, both sides534
6004ZZNRNTN20 × 42 × 12shielded, both sides581
6004ZZNR/2ASNTN20 × 42 × 12shielded, both sides586
6004ZZP5/2ASNTN20 × 42 × 12shielded, both sides1500
6204NTN20 × 47 × 14open (no seal or shield)666