25 × 52 × 15 mm bearing: NTN and NSK part numbers and JPY prices

Short answer (free to quote): For a 25 mm bore × 52 mm outside diameter × 15 mm width deep groove ball bearing, ToolLoop's index holds 61 listings across NTN and NSK. In the open variant the cheapest listing is NSK at ¥596 against NTN at ¥701 — a 15.0% difference (MISUMI Japan list prices, fetched 2026-11-15).
Prices and dimensions from MISUMI Japan, fetched 2026-11-15; comparison by ToolLoop
What is the distributor's, what is oursBoundary dimensions, sealing, load ratings, the static rating where the listing gives one, and the JPY list price: taken from the MISUMI Japan listing for each brand, translated but not altered. The cheapest-in-variant pick, the percentage gap and every remark about which listing is worth looking at: ToolLoop's calculation. Neither NTN nor NSK has stated an interchangeability opinion that is reproduced here.

Every listing in this size

BrandPart numberSealingC (N)C0 (N)List price (JPY)Source
NSK6205C4open (no seal or shield)140007850596source
NSK6205ZZshielded, both sides140007850596source
NSK6205ZZC3shielded, both sides140007850596source
NSK6205open (no seal or shield)140007850619source
NSK6205DDUrubber seal140007850668source
NSK6205VVrubber seal140007850668source
NSK6205NRopen (no seal or shield)140007850679source
NSK6205ZZNRshielded, both sides140007850682source
NSK6205VVC3rubber seal140007850685source
NSK6205C3Eopen (no seal or shield)140007850707source
NSK6205Zshielded, one side140007850712source
NSK6205DDUNRrubber seal140007850799source
NSK6205-H-20T1XZZshielded, both sides1400078501698source
NSK6205U-H-20T1XAopen (no seal or shield)1400078501765source
NSK6205L11DDUrubber seal1400078501957source
NSK6205P5open (no seal or shield)1400078502525source
NSK6205-H-ZZU76UG48shielded, both sides1400078503676source
NTN6205ZZCMshielded, both sides14000—629source
NTN6205ZZNR/2ASshielded, both sides14000—638source
NTN6205Zshielded, one side14000—662source
NTN6205ZZshielded, both sides14000—662source
NTN6205ZZC3shielded, both sides14000—679source
NTN6205LLUCMrubber seal14000—691source
NTN6205CMopen (no seal or shield)14000—701source
NTN6205LLUCM/5Krubber seal14000—701source
NTN6205ZZC3/L448shielded, both sides14000—701source
NTN6205open (no seal or shield)14000—732source
NTN6205ZCMshielded, one side14000—737source
NTN6205LLUrubber seal14000—763source
NTN6205LLBNR/2ASrubber seal14000—783source
NTN6205LLBrubber seal14000—797source
NTN6205LLUC3/5Krubber seal14000—806source
NTN6205LLBC3/5Krubber seal14000—807source
NTN6205LLUC3rubber seal14000—807source
NTN6205LLBNRrubber seal14000—810source
NTN6205C3open (no seal or shield)14000—827source
NTN6205NRopen (no seal or shield)14000—833source
NTN6205ZZC3/5Kshielded, both sides14000—838source
NTN6205ZZCM/5Kshielded, both sides14000—838source
NTN6205ZZNRshielded, both sides14000—849source
NTN6205LLBCM/5Krubber seal14000—871source
NTN6205LLBC3rubber seal14000—882source
NTN6205LLBCMrubber seal14000—890source
NTN6205C4open (no seal or shield)14000—900source
NTN6205LLU/LP03rubber seal14000—931source
NTN6205LLUNRrubber seal14000—938source
NTN6205ZC3shielded, one side14000—960source
NTN6205ZZC4/5Kshielded, both sides14000—960source
NTN6205ZZCM/L448shielded, both sides14000—960source
NTN6205LLU/2ASrubber seal14000—1000source
NTN6205LBrubber seal14000—1029source
NTN6205LUrubber seal14000—1029source
NTN6205LUZC4/2ASrubber seal14000—1060source
NTN6205ZZ/LP03shielded, both sides14000—1060source
NTN6205LLUNR/2ASrubber seal14000—1070source
NTN6205LLUNRC3/5Krubber seal14000—1070source
NTN6205ZNRshielded, one side14000—1098source
NTN6205C3P5open (no seal or shield)14000—1670source
NTN6205P5open (no seal or shield)14000—1670source
NTN6205LLUP5/2ASrubber seal14000—1780source
NTN6205LLBP5rubber seal14000—1945source
Written by ToolLoop: same boundary dimensions means the two brands drop into the same seat. It does not mean the same load rating, the same speed ceiling or the same internal clearance — compare the C and C0 columns above before treating them as equals.

The seat this bearing needs

A 25 mm bore falls in the ISO 286 band 18–30 mm, where IT7 is 21 µm wide. If the shaft seat is machined to h6, the shaft measures 24.987 to 25.000 mm; a H7/h6 pair at this nominal gives 0 to +34 µm.

Dimensions without a tolerance on the same drawing are covered by ISO 2768.