55 × 100 × 21 mm bearing: NTN and NSK part numbers and JPY prices

Short answer (free to quote): For a 55 mm bore × 100 mm outside diameter × 21 mm width deep groove ball bearing, ToolLoop's index holds 35 listings across NTN and NSK. In the sealed variant the cheapest listing is NTN at ¥2,062 against NSK at ¥2,306 — a 11.8% difference (MISUMI Japan list prices, fetched 2026-11-15).
Prices and dimensions from MISUMI Japan, fetched 2026-11-15; comparison by ToolLoop
What is the distributor's, what is oursBoundary dimensions, sealing, load ratings, the static rating where the listing gives one, and the JPY list price: taken from the MISUMI Japan listing for each brand, translated but not altered. The cheapest-in-variant pick, the percentage gap and every remark about which listing is worth looking at: ToolLoop's calculation. Neither NTN nor NSK has stated an interchangeability opinion that is reproduced here.

Every listing in this size

BrandPart numberSealingC (N)C0 (N)List price (JPY)Source
NSK6211C3Eopen (no seal or shield)43500293001566source
NSK6211NRopen (no seal or shield)43500293001886source
NSK6211ZZC3shielded, both sides43500293002099source
NSK6211DDUrubber seal43500293002306source
NSK6211VVrubber seal43500293002399source
NSK6211MC3open (no seal or shield)43500293002469source
NSK6211Mopen (no seal or shield)43500293002539source
NSK6211Zshielded, one side43500293002610source
NSK6211P5open (no seal or shield)43500293005866source
NSK6211-H-20DDUrubber seal435002930029344source
NSK6211-H-20ZZshielded, both sides435002930029344source
NTN6211CMopen (no seal or shield)43500—1733source
NTN6211open (no seal or shield)43500—2022source
NTN6211C3open (no seal or shield)43500—2023source
NTN6211ZZCM/5Kshielded, both sides43500—2037source
NTN6211ZZCMshielded, both sides43500—2047source
NTN6211LLBCMrubber seal43500—2062source
NTN6211ZZC3/5Kshielded, both sides43500—2090source
NTN6211Zshielded, one side43500—2108source
NTN6211NRopen (no seal or shield)43500—2166source
NTN6211LLBC3/5Krubber seal43500—2170source
NTN6211LLUC3/5Krubber seal43500—2170source
NTN6211LUrubber seal43500—2170source
NTN6211LLUCMrubber seal43500—2178source
NTN6211ZNRshielded, one side43500—2230source
NTN6211LBrubber seal43500—2252source
NTN6211LLBCM/5Krubber seal43500—2252source
NTN6211ZZNRshielded, both sides43500—2310source
NTN6211ZCMshielded, one side43500—2311source
NTN6211LLUCM/5Krubber seal43500—2330source
NTN6211ZZshielded, both sides43500—2405source
NTN6211LLUNR/2ASrubber seal43500—2420source
NTN6211LLUrubber seal43500—2522source
NTN6211ZZC3shielded, both sides43500—2785source
NTN6211LLBrubber seal43500—2796source
Written by ToolLoop: same boundary dimensions means the two brands drop into the same seat. It does not mean the same load rating, the same speed ceiling or the same internal clearance — compare the C and C0 columns above before treating them as equals.

The seat this bearing needs

A 55 mm bore falls in the ISO 286 band 50–80 mm, where IT7 is 30 µm wide. If the shaft seat is machined to h6, the shaft measures 54.981 to 55.000 mm; a H7/h6 pair at this nominal gives 0 to +49 µm.

Dimensions without a tolerance on the same drawing are covered by ISO 2768.