ISO 286 tolerances for 50–80 mm: IT grades and fit limits

Short answer (free to quote): In the 50–80 mm band of ISO 286-1, IT7 is 30 µm wide and IT6 is 19 µm, so an H7/h6 pair at a nominal 65 mm can move between 0 and +49 µm (calculated by ToolLoop, checked 2026-11-15). There are 728 deep groove ball bearing listings in ToolLoop's index with a bore in this band.
ISO 286-1:2010 tables; counts from the MISUMI Japan listing, fetched 2026-11-15
What is standard text, what is our arithmeticThe tolerance and deviation values are the tabulated values of ISO 286-1:2010 / ISO 2768-1:1989, taken from three independently published open datasets and compared cell by cell; only cells where all datasets that carry them agree are shown. The standard documents themselves are not reproduced. The limit sizes in millimetres, the clearance/interference ranges and every sentence about which fit is used for what are calculated or written by ToolLoop — they are not quoted from the standard.

Tolerance widths in this band

GradeWidth (µm)H hole EI/ES (µm)h shaft ei/es (µm)
IT5130 / +13+13 / 0
IT6190 / +19+19 / 0
IT7300 / +30+30 / 0
IT8460 / +46+46 / 0
IT9740 / +74+74 / 0
IT101200 / +120+120 / 0
IT111900 / +190+190 / 0

Fits in this band

FitHole EI/ESShaft ei/esClearance (µm)
H7/h60 / +30-19 / 00 … +49
H7/g60 / +30-29 / -10+10 … +59
H7/f70 / +30-60 / -30+30 … +90
H7/e80 / +30-106 / -60+60 … +136
H7/d90 / +30-174 / -100+100 … +204
H7/js60 / +30-9.5 / +9.5-9.5 … +39.5
H7/k60 / +30+2 / +21-21 … +28
H7/m60 / +30+11 / +30-30 … +19
H7/n60 / +30+20 / +39-39 … +10
H7/p60 / +30+32 / +51-51 … -2
H7/r60 / +30+41 / +60-60 … -11
H7/s60 / +30+53 / +72-72 … -23
H8/f70 / +46-60 / -30+30 … +106
H8/h70 / +46-30 / 00 … +76
H9/d90 / +74-174 / -100+100 … +248
H11/c110 / +190-330 / -140+140 … +520
Provenance: primary table ottonic/standards-mcp-server (src/domain/iso286.ts, MIT); cross-checked against clay-good/anvilate (tolerance/data/iso286_*.yaml, MIT) and chenzefeng09/iso-286-fits (fits.json, MIT). 393 overlapping cells compared, 0 disagreements, checked 2026-11-15.

Deep groove ball bearings with a bore in this band

728 listings; first 40 by bore.

Part numberBrandd × D × B (mm)SealingList price (JPY)
16011NTN55 × 90 × 11open (no seal or shield)2399
6011NTN55 × 90 × 18open (no seal or shield)2001
6011C3NTN55 × 90 × 18open (no seal or shield)1710
6011CMNTN55 × 90 × 18open (no seal or shield)2587
6011L1C3NTN55 × 90 × 18open (no seal or shield)2290
6011LLBNTN55 × 90 × 18rubber seal2657
6011LLBCMNTN55 × 90 × 18rubber seal1914
6011LLBCM/5KNTN55 × 90 × 18rubber seal2093
6011LLUNTN55 × 90 × 18rubber seal2657
6011LLUCMNTN55 × 90 × 18rubber seal1767
6011LLUCM/5KNTN55 × 90 × 18rubber seal2094
6011LLUNR/2ASNTN55 × 90 × 18rubber seal2280
6011NRNTN55 × 90 × 18open (no seal or shield)1940
6011ZNTN55 × 90 × 18shielded, one side2104
6011ZCMNTN55 × 90 × 18shielded, one side2507
6011ZZNTN55 × 90 × 18shielded, both sides2436
6011ZZC3NTN55 × 90 × 18shielded, both sides1836
6011ZZC3/5KNTN55 × 90 × 18shielded, both sides1880
6011ZZC4/5KNTN55 × 90 × 18shielded, both sides1880
6011ZZCMNTN55 × 90 × 18shielded, both sides1853
6011ZZCM/5KNTN55 × 90 × 18shielded, both sides1787
6011ZZNRNTN55 × 90 × 18shielded, both sides2598
6011ZZNR/2ASNTN55 × 90 × 18shielded, both sides2834
6211NTN55 × 100 × 21open (no seal or shield)2022
6211C3NTN55 × 100 × 21open (no seal or shield)2023
6211CMNTN55 × 100 × 21open (no seal or shield)1733
6211LBNTN55 × 100 × 21rubber seal2252
6211LLBNTN55 × 100 × 21rubber seal2796
6211LLBC3/5KNTN55 × 100 × 21rubber seal2170
6211LLBCMNTN55 × 100 × 21rubber seal2062
6211LLBCM/5KNTN55 × 100 × 21rubber seal2252
6211LLUNTN55 × 100 × 21rubber seal2522
6211LLUC3/5KNTN55 × 100 × 21rubber seal2170
6211LLUCMNTN55 × 100 × 21rubber seal2178
6211LLUCM/5KNTN55 × 100 × 21rubber seal2330
6211LLUNR/2ASNTN55 × 100 × 21rubber seal2420
6211LUNTN55 × 100 × 21rubber seal2170
6211NRNTN55 × 100 × 21open (no seal or shield)2166
6211ZNTN55 × 100 × 21shielded, one side2108
6211ZCMNTN55 × 100 × 21shielded, one side2311