85 × 180 × 41 mm bearing: NTN and NSK part numbers and JPY prices

Short answer (free to quote): For a 85 mm bore × 180 mm outside diameter × 41 mm width deep groove ball bearing, ToolLoop's index holds 26 listings across NTN and NSK. In the open variant the cheapest listing is NSK at ¥7,787 against NTN at ¥9,022 — a 13.7% difference (MISUMI Japan list prices, fetched 2026-11-15).
Prices and dimensions from MISUMI Japan, fetched 2026-11-15; comparison by ToolLoop
What is the distributor's, what is oursBoundary dimensions, sealing, load ratings, the static rating where the listing gives one, and the JPY list price: taken from the MISUMI Japan listing for each brand, translated but not altered. The cheapest-in-variant pick, the percentage gap and every remark about which listing is worth looking at: ToolLoop's calculation. Neither NTN nor NSK has stated an interchangeability opinion that is reproduced here.

Every listing in this size

BrandPart numberSealingC (N)C0 (N)List price (JPY)Source
NSK6317C3Eopen (no seal or shield)133000970007787source
NSK6317open (no seal or shield)133000970009891source
NSK6317C3open (no seal or shield)133000970009923source
NSK6317ZCMshielded, one side1330009700010027source
NSK6317DDUrubber seal1330009700010409source
NSK6317ZZshielded, both sides1330009700010415source
NSK6317VVrubber seal1330009700011183source
NSK6317P5open (no seal or shield)1330009700029560source
NTN6317ZZCMshielded, both sides133000—9020source
NTN6317C4open (no seal or shield)133000—9022source
NTN6317open (no seal or shield)133000—9806source
NTN6317CMopen (no seal or shield)133000—9806source
NTN6317ZZC3shielded, both sides133000—9887source
NTN6317C3open (no seal or shield)133000—9989source
NTN6317LLBCMrubber seal133000—10210source
NTN6317ZZshielded, both sides133000—10271source
NTN6317ZC3shielded, one side133000—10300source
NTN6317LLUC3rubber seal133000—11111source
NTN6317Zshielded, one side133000—11273source
NTN6317ZZC3/5Kshielded, both sides133000—11273source
NTN6317ZZCM/5Kshielded, both sides133000—11273source
NTN6317ZZCM/L448shielded, both sides133000—11273source
NTN6317LLUC3/5Krubber seal133000—11384source
NTN6317LUrubber seal133000—11384source
NTN6317LLBrubber seal133000—11588source
NTN6317LLBCM/5Krubber seal133000—11638source
Written by ToolLoop: same boundary dimensions means the two brands drop into the same seat. It does not mean the same load rating, the same speed ceiling or the same internal clearance — compare the C and C0 columns above before treating them as equals.

The seat this bearing needs

A 85 mm bore falls in the ISO 286 band 80–120 mm, where IT7 is 35 µm wide. If the shaft seat is machined to h6, the shaft measures 84.978 to 85.000 mm; a H7/h6 pair at this nominal gives 0 to +57 µm.

Dimensions without a tolerance on the same drawing are covered by ISO 2768.