ISO 286 tolerances for 80–120 mm: IT grades and fit limits

Short answer (free to quote): In the 80–120 mm band of ISO 286-1, IT7 is 35 µm wide and IT6 is 22 µm, so an H7/h6 pair at a nominal 100 mm can move between 0 and +57 µm (calculated by ToolLoop, checked 2026-11-15). There are 460 deep groove ball bearing listings in ToolLoop's index with a bore in this band.
ISO 286-1:2010 tables; counts from the MISUMI Japan listing, fetched 2026-11-15
What is standard text, what is our arithmeticThe tolerance and deviation values are the tabulated values of ISO 286-1:2010 / ISO 2768-1:1989, taken from three independently published open datasets and compared cell by cell; only cells where all datasets that carry them agree are shown. The standard documents themselves are not reproduced. The limit sizes in millimetres, the clearance/interference ranges and every sentence about which fit is used for what are calculated or written by ToolLoop — they are not quoted from the standard.

Tolerance widths in this band

GradeWidth (µm)H hole EI/ES (µm)h shaft ei/es (µm)
IT5150 / +15+15 / 0
IT6220 / +22+22 / 0
IT7350 / +35+35 / 0
IT8540 / +54+54 / 0
IT9870 / +87+87 / 0
IT101400 / +140+140 / 0
IT112200 / +220+220 / 0

Fits in this band

FitHole EI/ESShaft ei/esClearance (µm)
H7/h60 / +35-22 / 00 … +57
H7/g60 / +35-34 / -12+12 … +69
H7/f70 / +35-71 / -36+36 … +106
H7/e80 / +35-126 / -72+72 … +161
H7/d90 / +35-207 / -120+120 … +242
H7/js60 / +35-11 / +11-11 … +46
H7/k60 / +35+3 / +25-25 … +32
H7/m60 / +35+13 / +35-35 … +22
H7/n60 / +35+23 / +45-45 … +12
H7/p60 / +35+37 / +59-59 … -2
H7/r60 / +35+51 / +73-73 … -16
H7/s60 / +35+71 / +93-93 … -36
H8/f70 / +54-71 / -36+36 … +125
H8/h70 / +54-35 / 00 … +89
H9/d90 / +87-207 / -120+120 … +294
H11/c110 / +220-390 / -170+170 … +610
Provenance: primary table ottonic/standards-mcp-server (src/domain/iso286.ts, MIT); cross-checked against clay-good/anvilate (tolerance/data/iso286_*.yaml, MIT) and chenzefeng09/iso-286-fits (fits.json, MIT). 393 overlapping cells compared, 0 disagreements, checked 2026-11-15.

Deep groove ball bearings with a bore in this band

460 listings; first 40 by bore.

Part numberBrandd × D × B (mm)SealingList price (JPY)
6017NTN85 × 130 × 22open (no seal or shield)5092
6017CMNTN85 × 130 × 22open (no seal or shield)4355
6017LLBNTN85 × 130 × 22rubber seal4865
6017LLB/2ASNTN85 × 130 × 22rubber seal5147
6017LLBCMNTN85 × 130 × 22rubber seal4316
6017LLBCM/5KNTN85 × 130 × 22rubber seal4877
6017LLUNTN85 × 130 × 22rubber seal5087
6017LUNTN85 × 130 × 22rubber seal5514
6017ZCMNTN85 × 130 × 22shielded, one side4498
6017ZZNTN85 × 130 × 22shielded, both sides4576
6017ZZC3/5KNTN85 × 130 × 22shielded, both sides5824
6017ZZCMNTN85 × 130 × 22shielded, both sides4184
6017ZZCM/5KNTN85 × 130 × 22shielded, both sides4380
6017ZZNRNTN85 × 130 × 22shielded, both sides5559
6217NTN85 × 150 × 28open (no seal or shield)4373
6217C3NTN85 × 150 × 28open (no seal or shield)4239
6217CMNTN85 × 150 × 28open (no seal or shield)4338
6217LLBNTN85 × 150 × 28rubber seal6157
6217LLBCMNTN85 × 150 × 28rubber seal5457
6217LLBCM/5KNTN85 × 150 × 28rubber seal5911
6217NRNTN85 × 150 × 28open (no seal or shield)5154
6217ZNTN85 × 150 × 28shielded, one side5481
6217ZC3NTN85 × 150 × 28shielded, one side5850
6217ZZNTN85 × 150 × 28shielded, both sides5660
6217ZZC3NTN85 × 150 × 28shielded, both sides6414
6217ZZC3/5KNTN85 × 150 × 28shielded, both sides5021
6217ZZCMNTN85 × 150 × 28shielded, both sides4668
6217ZZCM/5KNTN85 × 150 × 28shielded, both sides5297
6317NTN85 × 180 × 41open (no seal or shield)9806
6317C3NTN85 × 180 × 41open (no seal or shield)9989
6317C4NTN85 × 180 × 41open (no seal or shield)9022
6317CMNTN85 × 180 × 41open (no seal or shield)9806
6317LLBNTN85 × 180 × 41rubber seal11588
6317LLBCMNTN85 × 180 × 41rubber seal10210
6317LLBCM/5KNTN85 × 180 × 41rubber seal11638
6317LLUC3NTN85 × 180 × 41rubber seal11111
6317LLUC3/5KNTN85 × 180 × 41rubber seal11384
6317LUNTN85 × 180 × 41rubber seal11384
6317ZNTN85 × 180 × 41shielded, one side11273
6317ZC3NTN85 × 180 × 41shielded, one side10300