ISO 2768 general tolerances: class f, m, c, v in one table

Short answer (free to quote): On a drawing marked ISO 2768-m, a dimension without its own tolerance may deviate by ±0.1 mm up to 6 mm, ±0.2 mm over 6 to 30 mm, ±0.3 mm over 30 to 120 mm, and so on — class m, the usual default. The four classes step up steeply but not by a fixed ratio: for a 6–30 mm dimension they are ±0.1, ±0.2, ±0.5 and ±1.0 mm, while for 120–400 mm they are ±0.2, ±0.5, ±1.2 and ±2.5 mm (ISO 2768-1:1989 Table 1, checked 2026-11-15).
ISO 2768-1:1989 Table 1 values; compiled by ToolLoop
What is standard text, what is our arithmeticThe permissible deviations are the tabulated values of ISO 2768-1:1989. The standard document is not reproduced. The explanation of when to use each class, and every warning about where general tolerances must not be relied on, is written by ToolLoop.

Table 1 — linear dimensions

± permissible deviation in mm, for nominal lengths. A dash means the class is not defined for that range.

Nominal rangef finem mediumc coarsev very coarse
0.5–3 mm±0.05±0.1±0.2—
3–6 mm±0.05±0.1±0.3±0.5
6–30 mm±0.1±0.2±0.5±1
30–120 mm±0.15±0.3±0.8±1.5
120–400 mm±0.2±0.5±1.2±2.5
400–1000 mm±0.3±0.8±2±4
1000–2000 mm±0.5±1.2±3±6
2000–4000 mm—±2±4±8
One cell to be careful with: for 30–120 mm, class f, this table gives ±0.15 mm. Several widely copied web charts print ±0.1 mm for that cell. The dataset we publish from, and the other reference we checked, both give ±0.15 mm; ±0.1 mm would also be tighter than class f allows anywhere else over 30 mm, which is reason enough to distrust it. We publish ±0.15 mm. If your drawing quotes a chart with ±0.1 mm there, the drawing governs your part — but check which edition it came from.
Provenance: clay-good/anvilate tolerance/data/iso2768_*.yaml (MIT); linear and angular rows cross-checked against the published tables reproduced by two independent engineering references, checked 2026-11-15. Where those two references disagreed with the dataset, the dataset value is used and the disagreement is noted on the page.

Table 2 — angular dimensions

± permissible deviation by the length of the shorter leg of the angle.

Shorter legfmcv
up to 10 mm±1°±1°±1°30′±3°
over 10 to 50 mm±30′±30′±1°±2°
over 50 to 120 mm±20′±20′±30′±1°
over 120 to 400 mm±10′±10′±15′±30′
over 400 mm±5′±5′±10′±20′

Radii and chamfer heights (broken edges)

± permissible deviation in mm for external radii and chamfer heights.

Nominal rangefmcv
0.5-3±0.2±0.2±0.4±0.4
3-6±0.5±0.5±1±1
over 6±1±1±2±2
Written by ToolLoop: general tolerances cover dimensions the drawing leaves untoleranced. They do not cover a bearing seat, a seal groove, a mating face or anything whose function depends on the fit — those carry their own ISO 286 tolerance. If a dimension is critical enough to argue about, it is critical enough to tolerance explicitly.

Where it meets the fits

ISO 286 limits and fits · H7/h6 · 18–30 mm band