10 × 35 × 11 mm bearing: NTN and NSK part numbers and JPY prices

Short answer (free to quote): For a 10 mm bore × 35 mm outside diameter × 11 mm width deep groove ball bearing, ToolLoop's index holds 31 listings across NTN and NSK. In the open variant the cheapest listing is NSK at ¥297 against NTN at ¥470 — a 36.8% difference (MISUMI Japan list prices, fetched 2026-11-15).
Prices and dimensions from MISUMI Japan, fetched 2026-11-15; comparison by ToolLoop
What is the distributor's, what is oursBoundary dimensions, sealing, load ratings, the static rating where the listing gives one, and the JPY list price: taken from the MISUMI Japan listing for each brand, translated but not altered. The cheapest-in-variant pick, the percentage gap and every remark about which listing is worth looking at: ToolLoop's calculation. Neither NTN nor NSK has stated an interchangeability opinion that is reproduced here.

Every listing in this size

BrandPart numberSealingC (N)C0 (N)List price (JPY)Source
NSK6300C3open (no seal or shield)81003450297source
NSK6300ZCMshielded, one side81003450391source
NSK6300DDUrubber seal81003450425source
NSK6300DDUC3rubber seal81003450432source
NSK6300ZZNRshielded, both sides81003450445source
NSK6300open (no seal or shield)81003450460source
NSK6300ZZshielded, both sides81003450479source
NSK6300VVrubber seal81003450481source
NTN6300ZZCMshielded, both sides8200—434source
NTN6300CMopen (no seal or shield)8200—470source
NTN6300C3open (no seal or shield)8200—489source
NTN6300LLBCMrubber seal8200—498source
NTN6300U1open (no seal or shield)8200—522source
NTN6300ZC3shielded, one side8200—566source
NTN6300open (no seal or shield)8200—576source
NTN6300LLUCM/5Krubber seal8200—630source
NTN6300ZZshielded, both sides8200—633source
NTN6300LLUCMrubber seal8200—638source
NTN6300ZZCM/5Kshielded, both sides8200—649source
NTN6300ZZC3/5Kshielded, both sides8200—650source
NTN6300ZZC3shielded, both sides8200—664source
NTN6300ZZNR/2ASshielded, both sides8200—664source
NTN6300LLBCM/5Krubber seal8200—665source
NTN6300LLUC3/5Krubber seal8200—727source
NTN6300LLUrubber seal8200—728source
NTN6300LLBC3rubber seal8200—752source
NTN6300LLBrubber seal8200—768source
NTN6300LLBC3/5Krubber seal8200—774source
NTN6300ZZNRshielded, both sides8200—795source
NTN6300ZU1shielded, one side8200—860source
NTN6300LUrubber seal8200—890source
Written by ToolLoop: same boundary dimensions means the two brands drop into the same seat. It does not mean the same load rating, the same speed ceiling or the same internal clearance — compare the C and C0 columns above before treating them as equals.

The seat this bearing needs

A 10 mm bore falls in the ISO 286 band 6–10 mm, where IT7 is 15 µm wide. If the shaft seat is machined to h6, the shaft measures 9.991 to 10.000 mm; a H7/h6 pair at this nominal gives 0 to +24 µm.

Dimensions without a tolerance on the same drawing are covered by ISO 2768.