12 × 37 × 12 mm bearing: NTN and NSK part numbers and JPY prices

Short answer (free to quote): For a 12 mm bore × 37 mm outside diameter × 12 mm width deep groove ball bearing, ToolLoop's index holds 33 listings across NTN and NSK. In the open variant the cheapest listing is NSK at ¥361 against NTN at ¥585 — a 38.3% difference (MISUMI Japan list prices, fetched 2026-11-15).
Prices and dimensions from MISUMI Japan, fetched 2026-11-15; comparison by ToolLoop
What is the distributor's, what is oursBoundary dimensions, sealing, load ratings, the static rating where the listing gives one, and the JPY list price: taken from the MISUMI Japan listing for each brand, translated but not altered. The cheapest-in-variant pick, the percentage gap and every remark about which listing is worth looking at: ToolLoop's calculation. Neither NTN nor NSK has stated an interchangeability opinion that is reproduced here.

Every listing in this size

BrandPart numberSealingC (N)C0 (N)List price (JPY)Source
NSK6301C3Eopen (no seal or shield)97004200361source
NSK6301DDUrubber seal97004200476source
NSK6301open (no seal or shield)97004200487source
NSK6301VVrubber seal97004200522source
NSK6301ZZNRshielded, both sides97004200557source
NSK6301Zshielded, one side97004200563source
NSK6301ZZshielded, both sides97004200563source
NSK6301ZZC3shielded, both sides97004200563source
NSK6301P5open (no seal or shield)970042001170source
NTN6301ZZshielded, both sides9700—473source
NTN6301Zshielded, one side9700—518source
NTN6301ZCMshielded, one side9700—583source
NTN6301C3open (no seal or shield)9700—585source
NTN6301LLUCM/5Krubber seal9700—589source
NTN6301CMopen (no seal or shield)9700—628source
NTN6301open (no seal or shield)9700—630source
NTN6301ZZCMshielded, both sides9700—644source
NTN6301ZZCM/5Kshielded, both sides9700—665source
NTN6301ZZC3/5Kshielded, both sides9700—678source
NTN6301LLUC3/5Krubber seal9700—692source
NTN6301LLBCMrubber seal9700—697source
NTN6301ZZNR/2ASshielded, both sides9700—708source
NTN6301ZZC3shielded, both sides9700—714source
NTN6301LLBC3/5Krubber seal9700—741source
NTN6301LLUCMrubber seal9700—756source
NTN6301LLUC3rubber seal9700—759source
NTN6301LLBCM/5Krubber seal9700—778source
NTN6301LLUrubber seal9700—778source
NTN6301LLBrubber seal9700—801source
NTN6301ZZNRshielded, both sides9700—803source
NTN6301LLBC3rubber seal9700—815source
NTN6301LUrubber seal9700—910source
NTN6301LLU/LP03rubber seal9700—1030source
Written by ToolLoop: same boundary dimensions means the two brands drop into the same seat. It does not mean the same load rating, the same speed ceiling or the same internal clearance — compare the C and C0 columns above before treating them as equals.

The seat this bearing needs

A 12 mm bore falls in the ISO 286 band 10–18 mm, where IT7 is 18 µm wide. If the shaft seat is machined to h6, the shaft measures 11.989 to 12.000 mm; a H7/h6 pair at this nominal gives 0 to +29 µm.

Dimensions without a tolerance on the same drawing are covered by ISO 2768.