15 × 28 × 7 mm bearing: NTN and NSK part numbers and JPY prices

Short answer (free to quote): For a 15 mm bore × 28 mm outside diameter × 7 mm width deep groove ball bearing, ToolLoop's index holds 32 listings across NTN and NSK. In the open variant the cheapest listing is NSK at ¥652 against NTN at ¥735 — a 11.3% difference (MISUMI Japan list prices, fetched 2026-11-15).
Prices and dimensions from MISUMI Japan, fetched 2026-11-15; comparison by ToolLoop
What is the distributor's, what is oursBoundary dimensions, sealing, load ratings, the static rating where the listing gives one, and the JPY list price: taken from the MISUMI Japan listing for each brand, translated but not altered. The cheapest-in-variant pick, the percentage gap and every remark about which listing is worth looking at: ToolLoop's calculation. Neither NTN nor NSK has stated an interchangeability opinion that is reproduced here.

Every listing in this size

BrandPart numberSealingC (N)C0 (N)List price (JPY)Source
NSK6902open (no seal or shield)43502260652source
NSK6902ZZshielded, both sides43502260686source
NSK6902Z1shielded, one side43502260699source
NSK6902CMopen (no seal or shield)43502260712source
NSK6902NRopen (no seal or shield)43502260713source
NSK6902ZZNRshielded, both sides43502260754source
NSK6902VVrubber seal43502260771source
NSK6902DDUrubber seal43502260790source
NSK6902DDrubber seal43502260801source
NSK6902-H-20T1XDDrubber seal43502260944source
NSK6902U-H-20T1Xopen (no seal or shield)43502260993source
NSK6902-H-20T1XZZ1shielded, both sides435022601038source
NSK6902-H-ZZU76UG1shielded, both sides435022602246source
NSK6902L11DD1rubber seal435022602607source
NSK6902L11DDrubber seal435022603483source
NTN6902ZZC3/5Kshielded, both sides3650—631source
NTN6902ZZ/2ASshielded, both sides3650—659source
NTN6902ZZNRshielded, both sides3650—682source
NTN6902Zshielded, one side3650—701source
NTN6902ZZC3shielded, both sides3650—704source
NTN6902ZZshielded, both sides3650—719source
NTN6902open (no seal or shield)3650—735source
NTN6902ZZNR/2ASshielded, both sides3650—756source
NTN6902LLBrubber seal3650—766source
NTN6902LLU/2ASrubber seal3650—806source
NTN6902LLB/2ASrubber seal3650—814source
NTN6902LLUrubber seal3650—822source
NTN6902ZZ/LP03shielded, both sides3650—879source
NTN6902NRopen (no seal or shield)3650—1010source
NTN6902LUrubber seal3650—1050source
NTN6902LLUNR/2ASrubber seal3650—1120source
NTN6902ZZP5/2ASshielded, both sides3650—1850source
Written by ToolLoop: same boundary dimensions means the two brands drop into the same seat. It does not mean the same load rating, the same speed ceiling or the same internal clearance — compare the C and C0 columns above before treating them as equals.

The seat this bearing needs

A 15 mm bore falls in the ISO 286 band 10–18 mm, where IT7 is 18 µm wide. If the shaft seat is machined to h6, the shaft measures 14.989 to 15.000 mm; a H7/h6 pair at this nominal gives 0 to +29 µm.

Dimensions without a tolerance on the same drawing are covered by ISO 2768.