20 × 52 × 15 mm bearing: NTN and NSK part numbers and JPY prices

Short answer (free to quote): For a 20 mm bore × 52 mm outside diameter × 15 mm width deep groove ball bearing, ToolLoop's index holds 36 listings across NTN and NSK. In the shielded variant the cheapest listing is NSK at ¥657 against NTN at ¥749 — a 12.3% difference (MISUMI Japan list prices, fetched 2026-11-15).
Prices and dimensions from MISUMI Japan, fetched 2026-11-15; comparison by ToolLoop
What is the distributor's, what is oursBoundary dimensions, sealing, load ratings, the static rating where the listing gives one, and the JPY list price: taken from the MISUMI Japan listing for each brand, translated but not altered. The cheapest-in-variant pick, the percentage gap and every remark about which listing is worth looking at: ToolLoop's calculation. Neither NTN nor NSK has stated an interchangeability opinion that is reproduced here.

Every listing in this size

BrandPart numberSealingC (N)C0 (N)List price (JPY)Source
NSK6304C3Eopen (no seal or shield)159007900562source
NSK6304ZZshielded, both sides159007900657source
NSK6304open (no seal or shield)159007900693source
NSK6304DDUrubber seal159007900701source
NSK6304VVrubber seal159007900736source
NSK6304ZZNRshielded, both sides159007900835source
NSK6304NRopen (no seal or shield)159007900903source
NTN6304CMopen (no seal or shield)15900—546source
NTN6304open (no seal or shield)15900—584source
NTN6304C3open (no seal or shield)15900—657source
NTN6304LLUrubber seal15900—718source
NTN6304LLBCM/5Krubber seal15900—748source
NTN6304ZZshielded, both sides15900—749source
NTN6304C4open (no seal or shield)15900—763source
NTN6304ZZC3shielded, both sides15900—766source
NTN6304LLUCM/5Krubber seal15900—790source
NTN6304ZZNR/2ASshielded, both sides15900—796source
NTN6304ZZCM/5Kshielded, both sides15900—837source
NTN6304LLUC3/5Krubber seal15900—838source
NTN6304Zshielded, one side15900—857source
NTN6304ZZC3/5Kshielded, both sides15900—884source
NTN6304LBrubber seal15900—894source
NTN6304LLUC3rubber seal15900—894source
NTN6304ZZNRshielded, both sides15900—896source
NTN6304LLBCMrubber seal15900—897source
NTN6304ZCMshielded, one side15900—940source
NTN6304LLBC3rubber seal15900—964source
NTN6304LLBC3/5Krubber seal15900—971source
NTN6304LLUCMrubber seal15900—979source
NTN6304LLBrubber seal15900—980source
NTN6304ZZC4/5Kshielded, both sides15900—1000source
NTN6304NRopen (no seal or shield)15900—1020source
NTN6304LUrubber seal15900—1060source
NTN6304LLBNR/2ASrubber seal—1140source
NTN6304LLUNR/2ASrubber seal15900—1140source
NTNEC-6304LLBC3/5Krubber seal15900—1270source
Written by ToolLoop: same boundary dimensions means the two brands drop into the same seat. It does not mean the same load rating, the same speed ceiling or the same internal clearance — compare the C and C0 columns above before treating them as equals.

The seat this bearing needs

A 20 mm bore falls in the ISO 286 band 18–30 mm, where IT7 is 21 µm wide. If the shaft seat is machined to h6, the shaft measures 19.987 to 20.000 mm; a H7/h6 pair at this nominal gives 0 to +34 µm.

Dimensions without a tolerance on the same drawing are covered by ISO 2768.