25 × 37 × 7 mm bearing: NTN and NSK part numbers and JPY prices

Short answer (free to quote): For a 25 mm bore × 37 mm outside diameter × 7 mm width deep groove ball bearing, ToolLoop's index holds 34 listings across NTN and NSK. In the shielded variant the cheapest listing is NTN at ¥779 against NSK at ¥1,011 — a 29.8% difference (MISUMI Japan list prices, fetched 2026-11-15).
Prices and dimensions from MISUMI Japan, fetched 2026-11-15; comparison by ToolLoop
What is the distributor's, what is oursBoundary dimensions, sealing, load ratings, the static rating where the listing gives one, and the JPY list price: taken from the MISUMI Japan listing for each brand, translated but not altered. The cheapest-in-variant pick, the percentage gap and every remark about which listing is worth looking at: ToolLoop's calculation. Neither NTN nor NSK has stated an interchangeability opinion that is reproduced here.

Every listing in this size

BrandPart numberSealingC (N)C0 (N)List price (JPY)Source
NSK6805open (no seal or shield)45003150928source
NSK6805DDrubber seal45003150954source
NSK6805ZZNRshielded, both sides450031501011source
NSK6805DDUrubber seal450031501049source
NSK6805ZZshielded, both sides450031501062source
NSK6805U-H-20T1Xopen (no seal or shield)450031501625source
NSK6805-H-20T1XDDrubber seal450031501842source
NSK6805-H-20T1XZZshielded, both sides450031502434source
NTN6805JRZshielded, one side4300—779source
NTN6805open (no seal or shield)4300—806source
NTN6805JRopen (no seal or shield)4300—820source
NTN6805Zshielded, one side4300—860source
NTN6805JRZZ/2ASshielded, both sides4300—882source
NTN6805LLU/2ASrubber seal4300—888source
NTN6805ZZ/2ASshielded, both sides4300—948source
NTN6805LLUrubber seal4300—971source
NTN6805ZZNRshielded, both sides4300—987source
NTN6805JRLLB/2ASrubber seal4300—988source
NTN6805NRopen (no seal or shield)4300—1002source
NTN6805ZZshielded, both sides4300—1008source
NTN6805JRLLUrubber seal4300—1031source
NTN6805LLB/2ASrubber seal4300—1031source
NTN6805JRLLU/2ASrubber seal4300—1034source
NTN6805JRZZshielded, both sides4300—1036source
NTN6805JRZZ/5Kshielded, both sides4300—1040source
NTN6805ZZ/5Kshielded, both sides4300—1042source
NTN6805LLBrubber seal4300—1065source
NTN6805ZZNR/2ASshielded, both sides4300—1070source
NTN6805JRZZ/LP03shielded, both sides4300—1098source
NTN6805JRLLBrubber seal4300—1115source
NTN6805JRZZC3/5Kshielded, both sides4300—1160source
NTN6805JRNRopen (no seal or shield)4300—1180source
NTN6805JRZZNRshielded, both sides4300—1244source
NTN6805ZZ/LP03shielded, both sides4300—1360source
Written by ToolLoop: same boundary dimensions means the two brands drop into the same seat. It does not mean the same load rating, the same speed ceiling or the same internal clearance — compare the C and C0 columns above before treating them as equals.

The seat this bearing needs

A 25 mm bore falls in the ISO 286 band 18–30 mm, where IT7 is 21 µm wide. If the shaft seat is machined to h6, the shaft measures 24.987 to 25.000 mm; a H7/h6 pair at this nominal gives 0 to +34 µm.

Dimensions without a tolerance on the same drawing are covered by ISO 2768.