30 × 55 × 13 mm bearing: NTN and NSK part numbers and JPY prices

Short answer (free to quote): For a 30 mm bore × 55 mm outside diameter × 13 mm width deep groove ball bearing, ToolLoop's index holds 52 listings across NTN and NSK. In the open variant the cheapest listing is NSK at ¥564 against NTN at ¥779 — a 27.6% difference (MISUMI Japan list prices, fetched 2026-11-15).
Prices and dimensions from MISUMI Japan, fetched 2026-11-15; comparison by ToolLoop
What is the distributor's, what is oursBoundary dimensions, sealing, load ratings, the static rating where the listing gives one, and the JPY list price: taken from the MISUMI Japan listing for each brand, translated but not altered. The cheapest-in-variant pick, the percentage gap and every remark about which listing is worth looking at: ToolLoop's calculation. Neither NTN nor NSK has stated an interchangeability opinion that is reproduced here.

Every listing in this size

BrandPart numberSealingC (N)C0 (N)List price (JPY)Source
NSK6006C3Eopen (no seal or shield)132008300564source
NSK6006VVC3Erubber seal132008300585source
NSK6006NRopen (no seal or shield)132008300609source
NSK6006DUCMrubber seal132008300626source
NSK6006ZZshielded, both sides132008300640source
NSK6006DDUNRrubber seal132008300655source
NSK6006open (no seal or shield)132008300680source
NSK6006ZZNRshielded, both sides132008300724source
NSK6006VVrubber seal132008300761source
NSK6006Zshielded, one side132008300783source
NSK6006DDUrubber seal132008300836source
NSK6006L11DDUrubber seal1320083001567source
NSK6006-H-20T1XDDUrubber seal1320083001998source
NSK6006-H-20T1XZZshielded, both sides1320083002380source
NSK6006P5open (no seal or shield)1320083002653source
NSK6006L11-H-20DDUrubber seal1320083007005source
NTN6006ZZCMshielded, both sides13200—585source
NTN6006ZZCM/5Kshielded, both sides13200—591source
NTN6006ZC3shielded, one side13200—601source
NTN6006Zshielded, one side13200—664source
NTN6006LUrubber seal13200—669source
NTN6006ZZshielded, both sides13200—728source
NTN6006LLBNRrubber seal13200—757source
NTN6006ZCMshielded, one side13200—763source
NTN6006ZZNR/2ASshielded, both sides13200—767source
NTN6006CMopen (no seal or shield)13200—779source
NTN6006LLBCM/5Krubber seal13200—798source
NTN6006NRopen (no seal or shield)13200—820source
NTN6006ZZC3shielded, both sides13200—829source
NTN6006LLUrubber seal13200—832source
NTN6006ZZC4shielded, both sides13200—846source
NTN6006ZNRshielded, one side13200—847source
NTN6006LLUNR/2ASrubber seal13200—848source
NTN6006LLBNR/2ASrubber seal13200—849source
NTN6006open (no seal or shield)13200—854source
NTN6006LLBCMrubber seal13200—890source
NTN6006LLUC3rubber seal13200—904source
NTN6006LBrubber seal13200—913source
NTN6006LLBrubber seal13200—916source
NTN6006ZZNRshielded, both sides13200—917source
NTN6006LLBC3/5Krubber seal13200—928source
NTN6006ZZC3/5Kshielded, both sides13200—956source
NTN6006ZZC4/5Kshielded, both sides13200—959source
NTN6006LLU/LP03rubber seal13200—996source
NTN6006LLUNRrubber seal13200—1017source
NTN6006LLBC3rubber seal13200—1034source
NTN6006LLUCMrubber seal13200—1034source
NTN6006LLU/2ASrubber seal13200—1050source
NTN6006LLUCM/5Krubber seal13200—1064source
NTN6006ZZ/LP03shielded, both sides13200—1130source
NTN6006LLB/LP03rubber seal13200—1200source
NTN6006P5open (no seal or shield)13200—1800source
Written by ToolLoop: same boundary dimensions means the two brands drop into the same seat. It does not mean the same load rating, the same speed ceiling or the same internal clearance — compare the C and C0 columns above before treating them as equals.

The seat this bearing needs

A 30 mm bore falls in the ISO 286 band 18–30 mm, where IT7 is 21 µm wide. If the shaft seat is machined to h6, the shaft measures 29.987 to 30.000 mm; a H7/h6 pair at this nominal gives 0 to +34 µm.

Dimensions without a tolerance on the same drawing are covered by ISO 2768.