35 × 80 × 21 mm bearing: NTN and NSK part numbers and JPY prices

Short answer (free to quote): For a 35 mm bore × 80 mm outside diameter × 21 mm width deep groove ball bearing, ToolLoop's index holds 47 listings across NTN and NSK. In the open variant the cheapest listing is NSK at ¥1,057 against NTN at ¥1,263 — a 16.3% difference (MISUMI Japan list prices, fetched 2026-11-15).
Prices and dimensions from MISUMI Japan, fetched 2026-11-15; comparison by ToolLoop
What is the distributor's, what is oursBoundary dimensions, sealing, load ratings, the static rating where the listing gives one, and the JPY list price: taken from the MISUMI Japan listing for each brand, translated but not altered. The cheapest-in-variant pick, the percentage gap and every remark about which listing is worth looking at: ToolLoop's calculation. Neither NTN nor NSK has stated an interchangeability opinion that is reproduced here.

Every listing in this size

BrandPart numberSealingC (N)C0 (N)List price (JPY)Source
NSK6307C3open (no seal or shield)33500192001057source
NSK6307C3Eopen (no seal or shield)33500192001318source
NSK6307ZZshielded, both sides33500192001408source
NSK6307VVC3rubber seal33500192001481source
NSK6307ZZNRshielded, both sides33500192001519source
NSK6307open (no seal or shield)33500192001545source
NSK6307VVrubber seal33500192001554source
NSK6307Zshielded, one side33500192001567source
NSK6307ZZC3shielded, both sides33500192001572source
NSK6307DDUrubber seal33500192001596source
NSK6307Mopen (no seal or shield)33500192001671source
NSK6307MC3open (no seal or shield)33500192001671source
NSK6307P5open (no seal or shield)33500192004078source
NTN6307ZZC4shielded, both sides33500—1250source
NTN6307CMopen (no seal or shield)33500—1263source
NTN6307ZZCM/L448shielded, both sides33500—1374source
NTN6307C3open (no seal or shield)33500—1404source
NTN6307open (no seal or shield)33500—1409source
NTN6307ZCMshielded, one side33500—1450source
NTN6307ZZCMshielded, both sides33500—1515source
NTN6307ZC3shielded, one side33500—1550source
NTN6307NRopen (no seal or shield)33500—1590source
NTN6307LLBCM/5Krubber seal33500—1598source
NTN6307ZZCM/5Kshielded, both sides33500—1606source
NTN6307LLUCM/5Krubber seal33500—1612source
NTN6307ZZC4/5Kshielded, both sides33500—1615source
NTN6307ZZNR/2ASshielded, both sides33500—1616source
NTN6307LLUrubber seal33500—1653source
NTN6307ZZshielded, both sides33500—1667source
NTN6307Zshielded, one side33500—1670source
NTN6307LLUC3/5Krubber seal33500—1684source
NTN6307LBrubber seal33500—1685source
NTN6307ZZC3/5Kshielded, both sides33500—1693source
NTN6307LLBNRrubber seal33500—1753source
NTN6307LLUCMrubber seal33500—1774source
NTN6307LLBC3rubber seal33500—1821source
NTN6307LLBCMrubber seal33500—1821source
NTN6307LLUNRrubber seal33500—1836source
NTN6307LUrubber seal33500—1860source
NTN6307ZZC3shielded, both sides33500—1901source
NTN6307LLUNR/2ASrubber seal33500—1923source
NTN6307LLBC3/5Krubber seal33500—1979source
NTN6307ZZNRshielded, both sides33500—1999source
NTN6307ZZ/LP03shielded, both sides33500—2030source
NTN6307LLUC3rubber seal33500—2058source
NTN6307LLBrubber seal33500—2233source
NTN6307LLBNR/2ASrubber seal33500—2537source
Written by ToolLoop: same boundary dimensions means the two brands drop into the same seat. It does not mean the same load rating, the same speed ceiling or the same internal clearance — compare the C and C0 columns above before treating them as equals.

The seat this bearing needs

A 35 mm bore falls in the ISO 286 band 30–50 mm, where IT7 is 25 µm wide. If the shaft seat is machined to h6, the shaft measures 34.984 to 35.000 mm; a H7/h6 pair at this nominal gives 0 to +41 µm.

Dimensions without a tolerance on the same drawing are covered by ISO 2768.