ISO 286 tolerances for 30–50 mm: IT grades and fit limits

Short answer (free to quote): In the 30–50 mm band of ISO 286-1, IT7 is 25 µm wide and IT6 is 16 µm, so an H7/h6 pair at a nominal 40 mm can move between 0 and +41 µm (calculated by ToolLoop, checked 2026-11-15). There are 785 deep groove ball bearing listings in ToolLoop's index with a bore in this band.
ISO 286-1:2010 tables; counts from the MISUMI Japan listing, fetched 2026-11-15
What is standard text, what is our arithmeticThe tolerance and deviation values are the tabulated values of ISO 286-1:2010 / ISO 2768-1:1989, taken from three independently published open datasets and compared cell by cell; only cells where all datasets that carry them agree are shown. The standard documents themselves are not reproduced. The limit sizes in millimetres, the clearance/interference ranges and every sentence about which fit is used for what are calculated or written by ToolLoop — they are not quoted from the standard.

Tolerance widths in this band

GradeWidth (µm)H hole EI/ES (µm)h shaft ei/es (µm)
IT5110 / +11+11 / 0
IT6160 / +16+16 / 0
IT7250 / +25+25 / 0
IT8390 / +39+39 / 0
IT9620 / +62+62 / 0
IT101000 / +100+100 / 0
IT111600 / +160+160 / 0

Fits in this band

FitHole EI/ESShaft ei/esClearance (µm)
H7/h60 / +25-16 / 00 … +41
H7/g60 / +25-25 / -9+9 … +50
H7/f70 / +25-50 / -25+25 … +75
H7/e80 / +25-89 / -50+50 … +114
H7/d90 / +25-142 / -80+80 … +167
H7/js60 / +25-8 / +8-8 … +33
H7/k60 / +25+2 / +18-18 … +23
H7/m60 / +25+9 / +25-25 … +16
H7/n60 / +25+17 / +33-33 … +8
H7/p60 / +25+26 / +42-42 … -1
H7/r60 / +25+34 / +50-50 … -9
H7/s60 / +25+43 / +59-59 … -18
H8/f70 / +39-50 / -25+25 … +89
H8/h70 / +39-25 / 00 … +64
H9/d90 / +62-142 / -80+80 … +204
H11/c110 / +160-280 / -120+120 … +440
Provenance: primary table ottonic/standards-mcp-server (src/domain/iso286.ts, MIT); cross-checked against clay-good/anvilate (tolerance/data/iso286_*.yaml, MIT) and chenzefeng09/iso-286-fits (fits.json, MIT). 393 overlapping cells compared, 0 disagreements, checked 2026-11-15.

Deep groove ball bearings with a bore in this band

785 listings; first 40 by bore.

Part numberBrandd × D × B (mm)SealingList price (JPY)
60/32NTN32 × 58 × 13open (no seal or shield)1119
60/32LLUNTN32 × 58 × 13rubber seal1341
60/32LLU/2ASNTN32 × 58 × 13rubber seal1406
60/32ZZNTN32 × 58 × 13shielded, both sides1232
60/32ZZ/2ASNTN32 × 58 × 13shielded, both sides1135
60/32ZZNR/2ASNTN32 × 58 × 13shielded, both sides1470
62/32NTN32 × 65 × 17open (no seal or shield)2041
62/32LLUNTN32 × 65 × 17rubber seal1897
62/32LLU/2ASNTN32 × 65 × 17rubber seal1599
62/32ZZNTN32 × 65 × 17shielded, both sides1474
62/32ZZ/2ASNTN32 × 65 × 17shielded, both sides1505
63/32NTN32 × 75 × 20open (no seal or shield)2330
63/32ZZNTN32 × 75 × 20shielded, both sides1551
63/32ZZ/2ASNTN32 × 75 × 20shielded, both sides1516
60/32NSK32 × 58 × 13open (no seal or shield)1341
60/32DDUNSK32 × 58 × 13rubber seal1653
60/32ZZNSK32 × 58 × 13shielded, both sides1582
62/32brand not stated32 × 65 × 17open (no seal or shield)1368
62/32VVbrand not stated32 × 65 × 17rubber seal1984
62/32ZZNSK32 × 65 × 17shielded, both sides1582
63/32DDUNSK32 × 75 × 20rubber seal1432
63/32ZZbrand not stated32 × 75 × 20shielded, both sides2345
16007NTN35 × 62 × 9open (no seal or shield)1095
6007C3NTN35 × 62 × 14open (no seal or shield)1048
6007CMNTN35 × 62 × 14open (no seal or shield)844
6007LBNTN35 × 62 × 14rubber seal1081
6007LLBNTN35 × 62 × 14rubber seal1018
6007LLBC3NTN35 × 62 × 14rubber seal1123
6007LLBC3/5KNTN35 × 62 × 14rubber seal1246
6007LLBCMNTN35 × 62 × 14rubber seal896
6007LLBCM/5KNTN35 × 62 × 14rubber seal942
6007LLBNRNTN35 × 62 × 14rubber seal1034
6007LLBNR/2ASNTN35 × 62 × 14rubber seal1023
6007LLBP5/2ASNTN35 × 62 × 14rubber seal2240
6007LLUNTN35 × 62 × 14rubber seal1018
6007LLU/LP03NTN35 × 62 × 14rubber seal1350
6007LLUC3/5KNTN35 × 62 × 14rubber seal1212
6007LLUCMNTN35 × 62 × 14rubber seal1011
6007LLUCM/5KNTN35 × 62 × 14rubber seal962
6007LLUNR/2ASNTN35 × 62 × 14rubber seal1260