40 × 68 × 15 mm bearing: NTN and NSK part numbers and JPY prices

Short answer (free to quote): For a 40 mm bore × 68 mm outside diameter × 15 mm width deep groove ball bearing, ToolLoop's index holds 42 listings across NTN and NSK. In the sealed variant the cheapest listing is NTN at ¥1,033 against NSK at ¥1,175 — a 13.7% difference (MISUMI Japan list prices, fetched 2026-11-15).
Prices and dimensions from MISUMI Japan, fetched 2026-11-15; comparison by ToolLoop
What is the distributor's, what is oursBoundary dimensions, sealing, load ratings, the static rating where the listing gives one, and the JPY list price: taken from the MISUMI Japan listing for each brand, translated but not altered. The cheapest-in-variant pick, the percentage gap and every remark about which listing is worth looking at: ToolLoop's calculation. Neither NTN nor NSK has stated an interchangeability opinion that is reproduced here.

Every listing in this size

BrandPart numberSealingC (N)C0 (N)List price (JPY)Source
NSK6008ZZshielded, both sides16800115001007source
NSK6008NRopen (no seal or shield)16800115001013source
NSK6008ZZC3shielded, both sides16800115001034source
NSK6008open (no seal or shield)16800115001098source
NSK6008VVrubber seal16800115001175source
NSK6008ZZNRshielded, both sides16800115001208source
NSK6008DDUNRrubber seal16800115001254source
NSK6008Zshielded, one side16800115001260source
NSK6008DDUrubber seal16800115001291source
NSK6008P5open (no seal or shield)16800115003638source
NSK6008U-H-20T1Xopen (no seal or shield)16800115005145source
NTN6008open (no seal or shield)16800—953source
NTN6008CMopen (no seal or shield)16800—1014source
NTN6008NRopen (no seal or shield)16800—1021source
NTN6008LLBCMrubber seal16800—1033source
NTN6008ZZC3/5Kshielded, both sides16800—1045source
NTN6008Zshielded, one side16800—1068source
NTN6008ZZshielded, both sides16800—1068source
NTN6008ZZCM/5Kshielded, both sides16800—1068source
NTN6008ZZCMshielded, both sides16800—1086source
NTN6008LBrubber seal16800—1155source
NTN6008LLBCM/5Krubber seal16800—1157source
NTN6008LLUCMrubber seal16800—1157source
NTN6008LUrubber seal16800—1177source
NTN6008LLUC3/5Krubber seal16800—1234source
NTN6008ZZC3shielded, both sides16800—1243source
NTN6008LLBNRrubber seal16800—1250source
NTN6008LLBNR/2ASrubber seal16800—1260source
NTN6008ZC3shielded, one side16800—1260source
NTN6008ZZC4/5Kshielded, both sides16800—1260source
NTN6008LLUrubber seal16800—1286source
NTN6008LLUCM/5Krubber seal16800—1299source
NTN6008LLUC3rubber seal16800—1303source
NTN6008LLBrubber seal16800—1315source
NTN6008LLUNR/2ASrubber seal16800—1332source
NTN6008LLBC3rubber seal16800—1346source
NTN6008ZZ/LP03shielded, both sides16800—1460source
NTN6008ZCMshielded, one side16800—1462source
NTN6008LLUNRrubber seal16800—1516source
NTN6008LLU/LP03rubber seal16800—1580source
NTN6008LLBC3/5Krubber seal16800—2098source
NTN6008P4open (no seal or shield)16800—5403source
Written by ToolLoop: same boundary dimensions means the two brands drop into the same seat. It does not mean the same load rating, the same speed ceiling or the same internal clearance — compare the C and C0 columns above before treating them as equals.

The seat this bearing needs

A 40 mm bore falls in the ISO 286 band 30–50 mm, where IT7 is 25 µm wide. If the shaft seat is machined to h6, the shaft measures 39.984 to 40.000 mm; a H7/h6 pair at this nominal gives 0 to +41 µm.

Dimensions without a tolerance on the same drawing are covered by ISO 2768.