40 × 80 × 18 mm bearing: NTN and NSK part numbers and JPY prices

Short answer (free to quote): For a 40 mm bore × 80 mm outside diameter × 18 mm width deep groove ball bearing, ToolLoop's index holds 52 listings across NTN and NSK. In the sealed variant the cheapest listing is NSK at ¥1,289 against NTN at ¥1,394 — a 7.5% difference (MISUMI Japan list prices, fetched 2026-11-15).
Prices and dimensions from MISUMI Japan, fetched 2026-11-15; comparison by ToolLoop
What is the distributor's, what is oursBoundary dimensions, sealing, load ratings, the static rating where the listing gives one, and the JPY list price: taken from the MISUMI Japan listing for each brand, translated but not altered. The cheapest-in-variant pick, the percentage gap and every remark about which listing is worth looking at: ToolLoop's calculation. Neither NTN nor NSK has stated an interchangeability opinion that is reproduced here.

Every listing in this size

BrandPart numberSealingC (N)C0 (N)List price (JPY)Source
NSK6208C4open (no seal or shield)29100179001154source
NSK6208ZZC3shielded, both sides29100179001287source
NSK6208DDUC3rubber seal29100179001289source
NSK6208ZZshielded, both sides29100179001303source
NSK6208DDUNRrubber seal29100179001329source
NSK6208NRopen (no seal or shield)29100179001364source
NSK6208ZZNRshielded, both sides29100179001375source
NSK6208open (no seal or shield)29100179001386source
NSK6208DDUrubber seal29100179001497source
NSK6208VVrubber seal29100179001497source
NSK6208MC3open (no seal or shield)29100179001524source
NSK6208Zshielded, one side29100179001531source
NSK6208C4P5open (no seal or shield)29100179003316source
NSK6208-H-20T1XADDUrubber seal29100179003439source
NSK6208P5open (no seal or shield)29100179004852source
NTN6208C3open (no seal or shield)29100—1178source
NTN6208CMopen (no seal or shield)29100—1197source
NTN6208open (no seal or shield)29100—1239source
NTN6208ZCMshielded, one side29100—1280source
NTN6208ZZC3/5Kshielded, both sides29100—1291source
NTN6208ZZshielded, both sides29100—1313source
NTN6208C4open (no seal or shield)29100—1320source
NTN6208ZZCMshielded, both sides29100—1322source
NTN6208Zshielded, one side29100—1392source
NTN6208LLUCMrubber seal29100—1394source
NTN6208LLUCM/5Krubber seal29100—1422source
NTN6208LLUC3/5Krubber seal29100—1429source
NTN6208ZZNR/2ASshielded, both sides29100—1436source
NTN6208ZC3shielded, one side29100—1440source
NTN6208ZC4shielded, one side29100—1440source
NTN6208ZZCM/5Kshielded, both sides29100—1475source
NTN6208NRopen (no seal or shield)29100—1484source
NTN6208LLBCMrubber seal29100—1514source
NTN6208ZZC3shielded, both sides29100—1529source
NTN6208LLUNR/2ASrubber seal29100—1594source
NTN6208LLBNR/2ASrubber seal29100—1690source
NTN6208L1C3rubber seal29100—1710source
NTN6208LLBCM/5Krubber seal29100—1721source
NTN6208LBrubber seal29100—1768source
NTN6208LLBC3rubber seal29100—1768source
NTN6208LLUrubber seal29100—1780source
NTN6208ZZNRshielded, both sides29100—1821source
NTN6208LLUC3rubber seal29100—1825source
NTN6208LUrubber seal29100—1899source
NTN6208LLBrubber seal29100—1901source
NTN6208M8C3P6open (no seal or shield)29100—1920source
NTN6208ZZ/LP03shielded, both sides29100—1970source
NTN6208LLUNRrubber seal29100—2108source
NTN6208LLU/LP03rubber seal29100—2140source
NTN6208LLBC3/5Krubber seal29100—2729source
NTN6208C3P5open (no seal or shield)29100—4740source
NTN6208LLBP5/2ASrubber seal29100—4945source
Written by ToolLoop: same boundary dimensions means the two brands drop into the same seat. It does not mean the same load rating, the same speed ceiling or the same internal clearance — compare the C and C0 columns above before treating them as equals.

The seat this bearing needs

A 40 mm bore falls in the ISO 286 band 30–50 mm, where IT7 is 25 µm wide. If the shaft seat is machined to h6, the shaft measures 39.984 to 40.000 mm; a H7/h6 pair at this nominal gives 0 to +41 µm.

Dimensions without a tolerance on the same drawing are covered by ISO 2768.