45 × 100 × 25 mm bearing: NTN and NSK part numbers and JPY prices

Short answer (free to quote): For a 45 mm bore × 100 mm outside diameter × 25 mm width deep groove ball bearing, ToolLoop's index holds 45 listings across NTN and NSK. In the open variant the cheapest listing is NSK at ¥1,766 against NTN at ¥2,501 — a 29.4% difference (MISUMI Japan list prices, fetched 2026-11-15).
Prices and dimensions from MISUMI Japan, fetched 2026-11-15; comparison by ToolLoop
What is the distributor's, what is oursBoundary dimensions, sealing, load ratings, the static rating where the listing gives one, and the JPY list price: taken from the MISUMI Japan listing for each brand, translated but not altered. The cheapest-in-variant pick, the percentage gap and every remark about which listing is worth looking at: ToolLoop's calculation. Neither NTN nor NSK has stated an interchangeability opinion that is reproduced here.

Every listing in this size

BrandPart numberSealingC (N)C0 (N)List price (JPY)Source
NSK6309C3Eopen (no seal or shield)53000320001766source
NSK6309NRopen (no seal or shield)53000320002413source
NSK6309C3open (no seal or shield)53000320002659source
NSK6309open (no seal or shield)53000320002833source
NSK6309DDUrubber seal53000320002855source
NSK6309ZZshielded, both sides53000320002857source
NSK6309ZZC3shielded, both sides53000320002986source
NSK6309ZZNRshielded, both sides53000320003071source
NSK6309MC3open (no seal or shield)53000320003078source
NSK6309VVrubber seal53000320003103source
NSK6309VVC3rubber seal53000320003165source
NSK6309Zshielded, one side53000320003299source
NSK6309L11DDUrubber seal53000320006820source
NSK6309P5open (no seal or shield)53000320007469source
NTN6309Zshielded, one side53000—2334source
NTN6309ZC3shielded, one side53000—2390source
NTN6309ZZC3/2ASshielded, both sides53000—2390source
NTN6309open (no seal or shield)53000—2501source
NTN6309CMopen (no seal or shield)53000—2545source
NTN6309LLUCMrubber seal53000—2619source
NTN6309LUrubber seal53000—2620source
NTN6309ZZC3/5Kshielded, both sides53000—2661source
NTN6309ZZNRshielded, both sides53000—2698source
NTN6309NRopen (no seal or shield)53000—2732source
NTN6309LLUCM/5Krubber seal53000—2784source
NTN6309C3open (no seal or shield)53000—2788source
NTN6309LLBrubber seal53000—2798source
NTN6309LLBCMrubber seal53000—2864source
NTN6309LLUC3/5Krubber seal53000—2887source
NTN6309ZZNR/2ASshielded, both sides53000—2892source
NTN6309LLBCM/5Krubber seal53000—2913source
NTN6309ZZCMshielded, both sides53000—2951source
NTN6309ZZCM/5Kshielded, both sides53000—2982source
NTN6309LLUC3rubber seal53000—3002source
NTN6309LLBC3rubber seal53000—3056source
NTN6309LLUrubber seal53000—3088source
NTN6309ZZshielded, both sides53000—3208source
NTN6309ZZC3shielded, both sides53000—3385source
NTN6309ZCMshielded, one side53000—3465source
NTN6309ZZC4shielded, both sides53000—3556source
NTN6309ZZC4/5Kshielded, both sides53000—3696source
NTN6309LLBNR/2ASrubber seal53000—4336source
NTN6309L1C3open (no seal or shield)53000—4620source
NTN6309LLUNR/2ASrubber seal53000—4620source
NTN6309ZZD2C3/5Kshielded, both sides53000—6620source
Written by ToolLoop: same boundary dimensions means the two brands drop into the same seat. It does not mean the same load rating, the same speed ceiling or the same internal clearance — compare the C and C0 columns above before treating them as equals.

The seat this bearing needs

A 45 mm bore falls in the ISO 286 band 30–50 mm, where IT7 is 25 µm wide. If the shaft seat is machined to h6, the shaft measures 44.984 to 45.000 mm; a H7/h6 pair at this nominal gives 0 to +41 µm.

Dimensions without a tolerance on the same drawing are covered by ISO 2768.