45 × 75 × 16 mm bearing: NTN and NSK part numbers and JPY prices

Short answer (free to quote): For a 45 mm bore × 75 mm outside diameter × 16 mm width deep groove ball bearing, ToolLoop's index holds 47 listings across NTN and NSK. In the open variant the cheapest listing is NSK at ¥1,006 against NTN at ¥1,167 — a 13.8% difference (MISUMI Japan list prices, fetched 2026-11-15).
Prices and dimensions from MISUMI Japan, fetched 2026-11-15; comparison by ToolLoop
What is the distributor's, what is oursBoundary dimensions, sealing, load ratings, the static rating where the listing gives one, and the JPY list price: taken from the MISUMI Japan listing for each brand, translated but not altered. The cheapest-in-variant pick, the percentage gap and every remark about which listing is worth looking at: ToolLoop's calculation. Neither NTN nor NSK has stated an interchangeability opinion that is reproduced here.

Every listing in this size

BrandPart numberSealingC (N)C0 (N)List price (JPY)Source
NSK6009C3Eopen (no seal or shield)20900152001006source
NSK6009ZZC3shielded, both sides20900152001125source
NSK6009ZZC3Eshielded, both sides20900152001155source
NSK6009ZZshielded, both sides20900152001302source
NSK6009DDUC3Erubber seal20900152001303source
NSK6009NRopen (no seal or shield)20900152001376source
NSK6009open (no seal or shield)20900152001422source
NSK6009DDUNRrubber seal20900152001472source
NSK6009DDUrubber seal20900152001490source
NSK6009VVrubber seal20900152001514source
NSK6009DUCMrubber seal20900152001525source
NSK6009Zshielded, one side20900152001528source
NSK6009ZZNRshielded, both sides20900152001561source
NSK6009P5open (no seal or shield)20900152003562source
NTN6009CMopen (no seal or shield)21000—1167source
NTN6009C3open (no seal or shield)21000—1238source
NTN6009LLBCMrubber seal21000—1251source
NTN6009LLUCMrubber seal21000—1251source
NTN6009ZC3shielded, one side21000—1254source
NTN6009ZZCMshielded, both sides21000—1269source
NTN6009ZZshielded, both sides21000—1361source
NTN6009ZZCM/5Kshielded, both sides21000—1368source
NTN6009LLBrubber seal21000—1398source
NTN6009LLUCM/5Krubber seal21000—1417source
NTN6009open (no seal or shield)21000—1418source
NTN6009ZZC3/5Kshielded, both sides21000—1420source
NTN6009ZZC4/5Kshielded, both sides21000—1460source
NTN6009ZZNR/2ASshielded, both sides21000—1474source
NTN6009LLBCM/5Krubber seal21000—1498source
NTN6009NRopen (no seal or shield)21000—1500source
NTN6009Zshielded, one side21000—1513source
NTN6009LBrubber seal21000—1519source
NTN6009LLUC3/5Krubber seal21000—1531source
NTN6009ZZC3shielded, both sides21000—1531source
NTN6009LUrubber seal21000—1580source
NTN6009LLBC3rubber seal21000—1595source
NTN6009LLBC3/5Krubber seal21000—1606source
NTN6009LLUNR/2ASrubber seal21000—1636source
NTN6009LLUrubber seal21000—1697source
NTN6009ZZ/LP03shielded, both sides21000—1730source
NTN6009LLUC3rubber seal21000—1776source
NTN6009ZZNRshielded, both sides21000—1838source
NTN6009LLB/LP03rubber seal21000—1880source
NTN6009LLUNRrubber seal21000—1972source
NTN6009ZCMshielded, one side21000—2395source
NTN6009P5open (no seal or shield)21000—3701source
NTN6009LLBP5/2ASrubber seal21000—5050source
Written by ToolLoop: same boundary dimensions means the two brands drop into the same seat. It does not mean the same load rating, the same speed ceiling or the same internal clearance — compare the C and C0 columns above before treating them as equals.

The seat this bearing needs

A 45 mm bore falls in the ISO 286 band 30–50 mm, where IT7 is 25 µm wide. If the shaft seat is machined to h6, the shaft measures 44.984 to 45.000 mm; a H7/h6 pair at this nominal gives 0 to +41 µm.

Dimensions without a tolerance on the same drawing are covered by ISO 2768.