45 × 85 × 19 mm bearing: NTN and NSK part numbers and JPY prices

Short answer (free to quote): For a 45 mm bore × 85 mm outside diameter × 19 mm width deep groove ball bearing, ToolLoop's index holds 42 listings across NTN and NSK. In the sealed variant the cheapest listing is NTN at ¥1,554 against NSK at ¥2,012 — a 29.5% difference (MISUMI Japan list prices, fetched 2026-11-15).
Prices and dimensions from MISUMI Japan, fetched 2026-11-15; comparison by ToolLoop
What is the distributor's, what is oursBoundary dimensions, sealing, load ratings, the static rating where the listing gives one, and the JPY list price: taken from the MISUMI Japan listing for each brand, translated but not altered. The cheapest-in-variant pick, the percentage gap and every remark about which listing is worth looking at: ToolLoop's calculation. Neither NTN nor NSK has stated an interchangeability opinion that is reproduced here.

Every listing in this size

BrandPart numberSealingC (N)C0 (N)List price (JPY)Source
NSK6209C4open (no seal or shield)31500204001372source
NSK6209ZZC3shielded, both sides31500204001401source
NSK6209ZZshielded, both sides31500204001558source
NSK6209ZZNRshielded, both sides31500204001684source
NSK6209Zshielded, one side31500204001948source
NSK6209DDUrubber seal31500204002012source
NSK6209Mopen (no seal or shield)31500204002133source
NSK6209L11DDUrubber seal31500204005219source
NSK6209P5open (no seal or shield)31500204005329source
NSK6209-H-20DDUrubber seal315002040024626source
NSK6209-H-20ZZshielded, both sides315002040024626source
NTN6209open (no seal or shield)32500—1476source
NTN6209CMopen (no seal or shield)32500—1496source
NTN6209C4open (no seal or shield)32500—1500source
NTN6209LLBCMrubber seal32500—1554source
NTN6209NRopen (no seal or shield)32500—1554source
NTN6209ZCMshielded, one side32500—1600source
NTN6209ZZshielded, both sides32500—1621source
NTN6209ZC3shielded, one side32500—1640source
NTN6209ZZ/2ASshielded, both sides32500—1640source
NTN6209ZZC4/5Kshielded, both sides32500—1640source
NTN6209C3open (no seal or shield)32500—1662source
NTN6209ZZCMshielded, both sides32500—1662source
NTN6209ZZNR/2ASshielded, both sides32500—1663source
NTN6209ZZC3shielded, both sides32500—1699source
NTN6209LUrubber seal32500—1770source
NTN6209ZZCM/5Kshielded, both sides32500—1780source
NTN6209Zshielded, one side32500—1785source
NTN6209LLUCM/5Krubber seal32500—1793source
NTN6209ZZC3/5Kshielded, both sides32500—1801source
NTN6209LLUCMrubber seal32500—1835source
NTN6209LLBCM/5Krubber seal32500—1848source
NTN6209LLUC3/5Krubber seal32500—1863source
NTN6209LLBrubber seal32500—1864source
NTN6209LLBC3/5Krubber seal32500—1913source
NTN6209LLUrubber seal32500—1923source
NTN6209LLUNR/2ASrubber seal32500—1960source
NTN6209LLUC3rubber seal32500—1964source
NTN6209LLBC3rubber seal32500—1975source
NTN6209LBrubber seal32500—2122source
NTN6209ZZNRshielded, both sides32500—2473source
NTN6209ZZP5/2ASshielded, both sides32500—5460source
Written by ToolLoop: same boundary dimensions means the two brands drop into the same seat. It does not mean the same load rating, the same speed ceiling or the same internal clearance — compare the C and C0 columns above before treating them as equals.

The seat this bearing needs

A 45 mm bore falls in the ISO 286 band 30–50 mm, where IT7 is 25 µm wide. If the shaft seat is machined to h6, the shaft measures 44.984 to 45.000 mm; a H7/h6 pair at this nominal gives 0 to +41 µm.

Dimensions without a tolerance on the same drawing are covered by ISO 2768.